Question about 2000 Ford Crown Victoria

1 Answer

BOUGHT EX-PATROL CAR, HAS ORINGINAL LINKAGE, HOW INSTALL

BOUGHT EX-PATROL CAR, HAS ORINGINAL LINKAGE, HOW DO I INSTALL........???????????? ( 2 METAL BARS FOOT LONG ONE WITH LOCK ATTACHED ...HELP)

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Check out this site just for your car:

http://www.crownvic.net/ubbthreads/ubbthreads.php

Posted on Sep 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my name is Sarah I just bought a 07/94 GQ NISSAN PATROL and I'm trying to find the engine number so I can register it can u help


No cannot help with that Sarah but if you go to one of the Nissan Patrol Forums and ask I am sure one of the guys there will help you out .
Try this one to start with in the link below and see how you go......................

Nissan Patrol GQ Y60 Ford Maverick

or this one

NissanPatrol com au Forum

Dec 15, 2015 | Nissan Cars & Trucks

1 Answer

How to turn idle down on Nissan patrol 99 turbo diesel 4.2


Idle is normally set for life but if you follow the linkage to the injector pump you will see it rests on a screw/bolt with a lock nut. Release the lock nut and turn the screw back until its what you want. Make sure the fast idle isn't caused by another fault like binding cable or linkage.

Dec 29, 2014 | Nissan Cars & Trucks

1 Answer

I've dismantled egr valve on 2006 nissan patrol zd30, there is a metal gasket and I cannot remember where it goes?


Metal gasket goes toward the intake & egr valve

Gasket first,egr next, then the bolts

If you took the egr apart, you may as well buy a new one

Can't clean it anyway

Aug 08, 2014 | 2006 Nissan Patrol 3.0

1 Answer

Shift Linkage for 1991 Mercury is loose


Your shifter bushings are worn out. Very easy fix. You can get shifter bushings from NAPA for about $2 ea, you need 4 of them. Drive the car onto ramps. Under the car there is a long rod that connects the shifter to the transmission. Unbolt the part connected to the shifter, remove old bushings (if they are still there), install new. Same for the where the shift rod connects to the transmission. 30 minute job, and it will shift great...Chris

Apr 16, 2013 | 1991 Mercury Capri

1 Answer

Hi my 1988 nissan patrol window wipers dont go in the high position,what would be the problem?


Hi,
The problem will be the wiper linkage, either the linkage connector are all broken and the motor needs adjustment! The connector are made of plastic and at the age of that patrol it might have been broken and needs a grease! U could access the linkage by removing the wiper motor and unscrew the wiper and wiper base! The easiest part is pulling it out... the hardest will be putting back! Don't worry, it takes time and patience and u could get it back again!

Jun 15, 2011 | Nissan King Cab Cars & Trucks

1 Answer

How to replace inside door handle on passenger on 1998 chevy silv


Remove screw from inside door grab handle. Remove door panel by carefully prying out plastic clips. Drill or chisel off pop rivets holding the handle on. Pull handle out far enough to disconnect linkage and remove handle. Install new handle and secure to metal panel with new pop rivets or sheet metal screws. It may be easier to reconnect linkages by removing the metal panel also.

Apr 11, 2009 | 1998 Chevrolet K1500

1 Answer

1999 CVPI Missing on 1 cylinder


My only question is if it's an "easy fix" why has she not done it...It certainly would be far easier to sell without the miss!

Apr 01, 2009 | 1999 Ford Crown Victoria

1 Answer

98 GOLF GL 2ND AND 4TH SHIFTING PROBLEMS I READ ONE BLOG QUESTION FROM 97 GOLF OWNER WITH SAME PROBLEM AND SOLLUTIONS WERE SYNCHRO CONE AND SHIFT LINKAGE ROD END. CAN EITHER ONE OF THESE SOLUTIONS BE DONE...


look inside engine compartment, locate the transmission has metal linkage arms with plastic round end connection in to metal half ball mechanism , play with system, move it back and forward, side to side, they are behind transmission and left side of car standing on front, by playing You will notice free play in one, that's the bad one, look in to getting all new

Jan 23, 2009 | 1997 Volkswagen Golf

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...