Question about 1994 Pontiac Bonneville

Open Question

How do I disengage the security system on my 1994 Pont Bonneville? It dies when I use the windows or door locks but its not the rear wondow defrost.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for security light in 96 pontiac bonneville??


Try using the door key to lock and un lock the drivers door. Pulling the fuse for the security system will guarantee the engine will never start.

Sep 29, 2016 | Pontiac Bonneville Cars & Trucks

1 Answer

How do you reset the security on '94 bonneville


assuming you dont have a remote and your key is good you can lock all the doors then unlock driver door with key should reset alarm system

Feb 14, 2011 | 1994 Pontiac Bonneville

2 Answers

Only the drivers door window and lock works on my 2000 bonneville none of the others work at either drivers door or any door


The power door locks and power windows in your vehicle are computer controlled. Each door has a computer module in it which operates the door lock actuators and the power window motors. All of the modules are connected together through the Class 2 data circuits. A scan tool capable of communicating with the body control computer systems in your car is required to properly diagnose and repair your door lock system.

Jan 24, 2011 | 2000 Pontiac Bonneville

1 Answer

94 pont grand prix how to disengage automatic locking when putting into gear


there is either a switch or key slot on shifter if no visual release you have to remove the cover and in shifter bse there will be a release

Jan 14, 2011 | 1994 Pontiac Grand Prix

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

1 Answer

00 pontiac bonneville right front, right


check the window lock switch on the drivers door armrest . It may have been pushed .

Feb 19, 2010 | 2000 Pontiac Bonneville

1 Answer

I have a 1994 4dr saturn and the rear drivers door will not open from the child lock being on how do i disengae it while the door is shut?


It'll be really hard to disengage it with the door shut as it's not designed that way. So I guess you aren't able to open the door from the outside at all. You'll have to take a jimmy and slide it into the window well to see if you can pop it from there

Sep 10, 2009 | 1994 Saturn Sl

1 Answer

My passenger door has no power,my security light is on constantly


Have lost power to the passenger side door. Without power system doesnt recognize door closed because of no power to door ajar switch which keeps dome light on. Security light stays on because without power to rest of systems supplied by fuse it cannot tell if doors and windows closed to engage security features. Most common is for power wire to break somewhere near where it leaves to main body and enters the door.

Apr 25, 2009 | 2003 Pontiac Bonneville

1 Answer

Car dies


check the wires leading to your rear window defroster, and do a general inspection of the reest of the wires that you feel comfortable with. make sure all connections are tight.

Apr 04, 2009 | 1994 Pontiac Bonneville

Not finding what you are looking for?
1994 Pontiac Bonneville Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...