Question about 2003 Honda Accord

Open Question

Turn signals are not working.

Turn signals (and hazards) are not working. which fuse should you check? There is not a clearly marked one.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 49 Answers

SOURCE: turn signals and hazards won't work

Was there any electrical issues other than this? Was there anything done to replace an electrical part or a stereo, gps, or other devices added to your car? Was a wire spliced or any wires cut that your aware of? Maybe the tail lights wiring have been altered to add as a source for connecting a trailer wiring harness? Try removing the **** shell around the ignition and carefully inspect the wiring in and around for loose, faulty or wires that may have been cut. Youll want to disconnect the battery first so you wont accidently create a short or spark that could create a bigger problem! Inspect your turn signal switch while you have the **** shell removed and make sure the parts are all intact and functioning, as well as the hazard switch. Could also be that theres simply a wire or wiring harness that had been disconnected while someone was working on another area related to the area where the problem is occuring. Hope this info is helpful or at least leads you in the direction of locating the problem.

Posted on Apr 18, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Turn singles and hazards are not working on my 2001 deville


I would replace the turn signal hazard combo switch.

Nov 28, 2016 | Cars & Trucks

3 Answers

TURN SIGNALS NOT WORKING


Turn signals are usually very reliable and problems mostly begin when a bulb is carelessly replaced. Other than this most problems are related to the hazard warning switch which tends to be used so infrequently the internal switch contacts become dull or dirty and so when it is operated causes turn signal problems, including them not working at all.

Usually spending a few minutes rapidly operating the hazard switch puts matters right.
It is also worth checking the fuse(s) before resorting to voltmeters and wiring diagrams.

Aug 10, 2015 | 1996 Jeep Grand Cherokee

3 Answers

Turn signals not working


all else on car works perfectly (other shoe drops??????)
waring 1: no scan tool, you will fail (99%)
is battery fully charged to 12.6vdc rested or at 10v?
all 4 corners dead?
not working means dead?, flashes too fast/slow or dim? or they stick on? (5 modes to fail not counting L/R and haz)
do the hazards work? (prime evidence and not stated)
most cars before 2007 have fuse marked TURN.
but not this car... its not at all like older cars....
did you scan it first after the fuse tests? any PCM scan tool.?
2009 WK jeep
the FSM chapter 8L shows the huge list of errors the lamps can fail. DTC errors.
in fact 8 blinker codes, ! DTC errors,

there is no fuse, just for turns, (trailer lamps fuse 19)

read this excerpt from the FSM book.

The turn signal system operates on battery current received on a fused ignition switch output (run) circuit so that the
turn signals will only operate with the ignition switch in the On position. The hazard warning system operates on
non-switched battery current received on a fused B(+) circuit so that the hazard warning remains operational regardless
of the ignition switch position. When the turn signal system is activated, the circuitry of the left multi-function
switch and the FCM will cause the selected (right or left) turn signal indicator, front park/turn signal lamp, front side
marker lamp and rear tail/stop/turn signal lamp to flash on and off. When the hazard warning system is activated,
the circuitry of the hazard warning switch and the FCM will cause both the right side and the left side turn signal
indicators, front park/turn signal lamps, front side marker lamps and rear tail/stop/turn signal lamps to flash on and
off. The Front Control Module (FCM) can also activate the hazard warning system lamps.
end quote)

the module front control MFC, runs this
and it uses fuse 18 , if 18 blows the module goes off line and vast things fail and huge numbers OF DTCs store.
and fuse 27 MFC
MFC needs these fuses good.
keep in mind nobody has MFC internal schematics...so........



this module drives left and right side front and rear.
electronic drivers, not fuses.
the MFC is here.
the fuses are 12,13,18, 20,27 that power MFC.


25812039-lb3yimx2pwhstnjl4tgwffiq-2-0.jpg ground this end.

Aug 07, 2015 | 2009 Jeep Grand Cherokee

1 Answer

The signal and the hazard lights are not working


as in all elect. issues, fuses first.
check fuses in all boxes or the one clearly marked Turn.

does no working mean dead, or stuck on. not blinking.
or blinking too fast or slow>?

box 1, fuse 17 and 19. usually both dont blow but can if
shorted out lamps or shorted wiring, or trailer hatch hacks, shorteed.

25580808-gqg4vgattcy132cyk4df3qpe-1-0.jpg if the fuse blows, again, the system TURNS is shorted out.
ask for help how to use a meter to find it
or get it serviced.

Mar 16, 2015 | 2004 Suzuki Aerio

1 Answer

Turn signal are not working fuse box


the fuse panel is under the dash on the drivers side check all the fuses.it could be the signal flasher there are two flashers one for the hazard lights and another one for the signal lights,they look the same.they are round and usually silver in colour some of them have a clear cover instead of a metal cover.

Apr 14, 2011 | 1987 Oldsmobile Ninety Eight

1 Answer

Question how to repair directional signal - the signals quit working after the hazard button was stuck "on". We have removed the fuse for the hazard & replaced the fuse for the signal but...


Some car and van turn signals will not work while the four way flashers are on. If the button is stuck, and you can't pull it out by hand. Take a plyers and only sqweeze hard enough on the handles while pulling, that you don't slip on the button and mark it up. Just a suggestion, put a rag on the button before putting the plyers on it. The blinkers should work after the button gets pulled out. When the button is pulled out and the turn signals still don't work, check both taillights and the turn signal lights at the front. Make sure they're not corroded (rusty).

Jan 23, 2011 | Honda Accord Cars & Trucks

3 Answers

Turn signals dont work


that could easily be just the fuse or the flasher unit. both are on the driver side under the dash

Mar 10, 2010 | 1991 Ford Tempo 4 Door

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

1 Answer

Haz flashers wont work but blinkers do


There are 2 seperate flashers 1 for turn signals and 1 for hazard.The hazard flasher is located in the convenance center the turn flasher in the fuse box. Also seperate fuse's for each. One battery circuit for hazard Ignition for turn signals.Check fuse for hazard,if good try swapping in the turn signal flasher and see if hazards work.They use the same flasher unit.

Aug 20, 2009 | 1993 GMC Safari

1 Answer

1993 mark VIII blower motr stopped working, Also the hazard and turn signals not working. I replaced the 30 green fuse. did not solve problem,but this 30 fuse controls both haz and blower. So it must be a...


Dont know whay the blower motor doesnt work, but that age with these cars (I have two 94 Marks) both have had the turn signal switch replaced for problems with hazards not working, wipers not shutting off, etc.
To check your climate control system: Press OFF and FLOOR at the same time, release, then hit AUTO. That will make it self-test. You will get 888 (ok) or an error code (024, 025, or such)

Jan 18, 2009 | 1993 Lincoln Mark VIII

Not finding what you are looking for?
2003 Honda Accord Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...