Question about 1997 Chevrolet Malibu

1 Answer

The power steering pump pulley is broken, but can not remove it with out taking out center bolt, which way does it loosen? toward the engine compartment or toward the radiator

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Pulley is pressed on

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

How do I fix a broken power steering belt without having to pull the engine??


Shouldn't have to. All belts can be replaced without pulling the engine. On some, you may have to remove other belts in order to get the first one on the crank pulley and fitted, and then put the other belt or belts on. Is the broken belt stuck somewhere? Loosening the power steering pump to swing it toward the engine for belt removal can be tricky on some Chryslers-don't know about your PT. On a Chrysler Cirrus you have to loosen 3 bolts and one is on the back side of the pump bracket.

Dec 12, 2012 | 2009 Chrysler PT Cruiser

1 Answer

What do i do to get new belt on


FOR THE 3.0L ENGINE IF YOU REPLACE AC BELT LOOSEN TOP IDLER PULLEY CENTER BOLT. IF YOU REPLACING ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTMENT BOLT AND PIVOT BOLT.IF REPLACING POWER STEERING PUMP BELT LOOSEN POWER STEERING PUMP ADJUSTMENT BOLT AND MOUNTING BOLTS.****** FOR THE 2.4L ENGINE TO REMOVE POWER STEERING BELT LOOSEN TOP IDLER PULLEY.FOR ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTER BOLT, PIVOT AND MOUNTING BOLTS.FOR AC COMPRESSOR LOOSEN LOWER IDLER PULLEY.

Oct 07, 2010 | 1996 Nissan Pickup

1 Answer

Belt routing for 2000 ford escourt


The belt routing is often found on a sticker, under the hood. But, the best I can do is instructions on how to change the belts, step by step:
REMOVAL & INSTALLATION 1.8L Engines ALTERNATOR AND WATER PUMP BELT
  1. Riase the front of the car and support it with safety stands.
  2. Loosen the alternator adjusting bolt.
  3. If necessary, remove the power steering drive belt .
  4. Loosen the alternator mounting bolt.
  5. Remove the alternator and water pump drive belt. To install:
  6. Install the alternator and water pump drive belt.
  7. Adjust the belt tension.
  8. If removed, install the power steering pump belt.
  9. Tighten the alternator adjusting bolt to 14–19 ft. lbs. (19–25 Nm).
  10. Tighten the alternator mounting bolt to 27–38 ft. lbs. (37–52 Nm).
  11. Lower the vehicle.
POWER STEERING PUMP BELT
  1. Raise and safely support the vehicle.
  2. Loosen the power steering pump mounting bolt and nuts.
  3. Remove the drive belt. To install:
  4. Install the belt and adjust the tension.
  5. Tighten the power steering pump mounting nut, located near the adjusting bolt, to 27–38 ft. lbs. (37–52 Nm).
  6. Tighten the pump mounting bolt behind the pulley to 27–40 ft. lbs. (36–54 Nm), and the remaining pump mounting nut to 23–34 ft. lbs. (31–46 Nm).
  7. Lower the vehicle.
1.9L and 2.0L SOHC Engines
  1. Insert a 3?8 in. drive ratchet or a breaker bar in the hole on the automatic tensioner, then pull the tool toward the front of the vehicle.
  2. While releasing the belt tension, remove the drive belt from the tensioner pulley and slip it off the remaining accessory pulleys. Fig. 1: Insert a 3?8 in. drive ratchet or breaker bar into the hole of the automatic tensioner 90981p74.jpg
    Fig. 2: Pull the breaker bar or ratchet toward the front of the vehicle to relieve belt tension 90981p75.jpg
    Fig. 3: Once the tension has been released, remove the belt from the pulleys and the vehicle 90981p76.jpg
    To install:
  3. Position the drive belt over the accessory pulleys.
  4. Insert the 3?8 in. drive ratchet or breaker bar into the hole of the automatic tensioner, then pull the tool toward the front of the vehicle.
  5. While holding the tool in this position, slip the drive belt behind the tensioner pulley and release the tool.
  6. Remove the tool from the automatic tensioner.
  7. Check that all V-grooves make proper contact with the pulley.
2.0L DOHC Engines
  1. Raise the car and safely support it with jackstands.
  2. Use a 13mm wrench to rotate the tensioner clockwise.
  3. Remove the drive belt from the pulleys. To install:
  4. Position the belt on the pulleys.
  5. Use a 13mm wrench to rotate the tensioner clockwise.
  6. Route the belt as shown in the illustration and release the tensioner.
  7. Lower the car.
  8. Run the engine for a few minutes to seat the belt in the pulley grooves.
prev.gif next.gif

Sep 03, 2010 | Ford Escort Cars & Trucks

1 Answer

I need to replace my 2007 Honda Odyssey Power Sterring Pump? How hard is this and would it be better for me to take it to someone to have it done?


Not that bad to do, loosen nut on center of pulley before removing belt, this way it will hold pulley while loosening nut, after that remove belt, remove both power steering hoses, now remove pulley and both mounting bolt to power steering pump, install new pump in reverse order.

Jun 14, 2010 | 2007 Honda Odyssey

1 Answer

How to change the fan belts on 1993 Nissan Quest Minivan


First go to Nissan's help forum page. Use this link: http://x.nissanhelp.com/forums/index.php

You can get a free login and download up to two files a day using the free login. You want the MA maintenance file of your vans manual. This will include the belt tensions and placement.
You will need to remove the plastic cover on the passenger side of the engine to be able to access the belt tensioners on the alt. and power steering pump. Nissan likes to use the same basic tensioners on most of their stuff. The air pump and air conditioner use idler pulleys, you loosen the bolt in the middle of the pulley enough to allow the pulley to move, no more. there is a bolt with its length toward the center of this pulley, when you loosen this bolt the pulley will start to move down and loosen the belt. repeat this process for both the air pump and the air conditioner. The alt. and power steering you loosen the bolt that secures the tensioner, than you can back off the long bolt in the tensioner to loosen and remove the belts.

I usually check each new built with the old one for length and label its sleeve by function as I take each one off. Makes matching them up when you put them back on much easier.

Sep 05, 2009 | 1994 Nissan Quest

2 Answers

Can't get A/C belt around pulleys on my 01 Chevy Tracker 2.5 V6



Removal & Installation

1.6L Engine
A/C Compressor Belt
  1. Disconnect the negative battery cable.
  2. Loosen the A/C compressor mounting bolts.
  3. Pivot the A/C compressor towards the engine in order to relieve the tension on the belt.
  4. Remove the A/C compressor drive belt from the pulleys.

To install:
  1. Properly route and install the A/C compressor drive belt on the A/C compressor, the power steering (if equipped), and the crankshaft pulleys.
  2. Adjust the A/C compressor drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the A/C compressor mounting bolts to 13-20 f t. lbs. (18-28 Nm).
  4. Connect the negative battery cable.

Alternator Belt
  1. Disconnect the negative battery cable.
  2. Remove the power steering pump and the A/C compressor drive belt.
  3. Loosen the generator mounting bolts.
  4. Pivot the generator towards the engine and remove the accessory drive belt.

To install:
  1. Properly route and install the generator drive belt on the pulleys.
  2. Adjust the alternator drive belt to obtain 6-8 mm (0.24-0.32 in) deflection for a used belt or 5-6 mm (0.20-0.24 in) deflection for a new belt.
  3. Tighten the generator mounting bolts to 17 ft. lbs. (23 Nm).
  4. Install the power steering and the A/C compressor drive belt.
  5. Connect the negative battery cable.

Power Steering Pump Belt
  1. Disconnect the negative battery cable.
  2. Loosen the power steering pump mounting bolts.
  3. Pivot the power steering pump towards the engine in order to relieve the tension on the belt.
  4. Remove the power steering pump drive belt from the pulleys.

To install:
  1. Properly route and install the power steering pump drive belt on the power steering pump and the crankshaft pulleys.
  2. Adjust the power steering pump drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
  3. Tighten the power steering pump mounting bolts to 22 ft. lbs. (30 Nm).
  4. Connect the negative battery cable.

Apr 26, 2009 | 2001 Chevrolet Tracker

1 Answer

Removing a 1987 ford tempo power steering pump


I believe you have 2 beltson this engine. One for the alternator, a short skinny one. Loosening the alternator bolts and pulling the alternator towards the front of the car, and then tightening the adjusting bolt.
The other belt runs the power steering, a/c compressor and water pump. I think it has an idler pulley with a jack screw adjusting screw. loosen the screw to releive belt tension. good luck

Jan 10, 2009 | 1987 Ford Tempo

4 Answers

Change Belts on 1997 Kia Sportage


This is the KIA tech site. Free to register and use. It lists the repair tech manuals, Sevice Bulletins, How-to's, and troubleshooting guides the factory trained repair guys use:
http://www.kiatechinfo.com/index.asp

Sep 26, 2008 | 1997 Kia Sportage

1 Answer

Loosen tension on serpent belt


Hi rdt,
The tensioner is on a spring arm, no need to take it off.
  • Get a 14mm or 9/16" socket and a long handled ratchet or breaker bar.
  • Get the belt around all the pulleys except the A/C compressor or Alternator.
  • The tensioner pulley is near the Alternator toward the center of the engine. It's on a spring loaded arm. Get your socket on the center nut of this pulley.
  • Slowly pull the ratchet toward the center of the engine. The pulley will pivot on the arm allowing you to get the belt on the final pulley.
  • Slowly release the tension.
  • You're done
Mike

Jul 19, 2008 | 2002 Kia Optima

Not finding what you are looking for?
1997 Chevrolet Malibu Logo

Related Topics:

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...