Can't figure out how to re-instal,need picture

Due to poor spelling it is not possible to figure out what you are referring to.

Depiction is a form of non-verbal representation in which two-dimensional images (pictures) are regarded as viable substitutes for things seen, remembered or imagined. Basically, a picture maps an object to a two-dimensional scheme or picture plane. Pictures are made with various materials and techniques, such as painting, drawing, or prints (including photography and movies) mosaics, tapestries, stained glass, and collages of unusual and disparate elements. Occasionally pictures may occur in simple inkblots, accidental stains, peculiar clouds or a glimpse of the moon, but these are special cases. Sculpture and performances are sometimes said to depict but this arises where depiction is taken to include all reference that is not linguistic or notational. The bulk of research in depiction however deals only in pictures. While sculpture and performance clearly represent or refer, they do not strictly picture their objects.
Pictures may be factual or fictional, literal or metaphorical, realistic or idealised and in various combination. Idealised depiction is also termed schematic or stylised and extends to icons, diagrams and maps. Classes or styles of picture may abstract their objects by degrees, conversely, establish degrees of the concrete (usually called, a little confusingly, figuration or figurative, since the 'figurative' is then often quite literal). Stylisation can lead to the fully abstract picture, where reference is only to conditions for a picture plane - a severe exercise in self-reference and ultimately a sub-set of pattern.
But just how pictures function (i.e. how they can be viably substituted for three-dimensional objects etc.) is disputed. Philosophers, art historians and critics, perceptual psychologists and other researchers in the arts and social sciences have contributed to the debate and many of the most influential contributions have been interdisciplinary. Some key positions are briefly surveyed below.

Courtesy of Wickipedia.org.
You can go to that link for any further definitions you need.

Are you installing an engine that you didn't pull out? The best thing is to make sure you know where everything goes as your disconnecting them. Either by taking pictures or tagging. If you are putting an engine in that has been pulled out by someone else it would be almost impossible to show everything. Some connectors go on where you can't hardly see them let it alone take a picture of them. If you take your time and sort through things usually every connector is a little different and you should be able to figure out the electrical connectors. The hoses, If they were left intact should almost only reach one place. GOOD LUCK

Technical Instructions
See picture below
1. Remove door trim panel and water shield per
NOTE: Place a strip of masking tape along the edge of door before removing trim panel to prevent scratching the door with the trim panel removal tool.

2. Snap cable housing end from slot on inside door handle assembly and disconnect cable.
NOTE: Use care to prevent bending of cable housing retainer bracket.

3. Remove rear window channel retaining bolt to allow access to door latch.

4. Position a block (screwdriver handle) between the latch and the door inner panel and snap the cable housing end out of slot (towards inner panel) on door latch assembly and disconnect cable at latch.
NOTE: Use care when removing cable housing to avoid bending of the latch. Discard cable.

5. Hook up new cable at latch and snap cable housing end into slot.
NOTE: Make sure the cable housing is fully seated in the slot.

6. Apply a light film of Teflon grease to the barrel end of the cable. See Figure A.

7. Install return spring. See Figure A.
NOTE: Ensure that the push button rod is located between the spring and the door inner panel.

8. Install foam block at latch. See Figure A.

9. Position water shield over the return spring and install push pin to retain upper portion of water shield. See Figure B.
NOTE: Push pin goes in the same hole as the return spring.

10. Clean hands of grease before performing step 11.

11. Remove protective backing along the lower edges only of the water shield. See Figure A.

12. Install latch water shield at door latch. Pinch the exposed adhesive surfaces together to secure the water shield. Check to insure water shield is not showing through the door shut-face latch access hole. See Figure B.

13. Attach cable to inside door handle assembly and snap cable housing into slot.
NOTE: Make sure the cable housing is fully seated.

14. Check the gap as shown in remote control using a 3/16 drill bit shank end. The drill bit shank should fit in the gap without any clearance and a tight fit is preferred. See Figure C.

15. If the drill bit is too loose or does not fit, adjust by bending the cable bracket as required.

16. Place plastic wedge on remote bracket as shown. Wedge must fit with at least a light press fit for retention. See Figure D.

17. After installation, Apply a dab of special Teflon grease, supplied with the service cable to cable housing openings at inside handle end. The grease should surround and contact the cable all the way around, to seal the opening between the cable and the cable housing.

18. Check all latch functions to insure correct assembly of latch system. If the inside handle does not release properly, replace the inside handle remote release mechanism.

19. Reposition and install trim panel using new push pins if required.

Did you by chance mix up the shoes,adjuster etc? Short shoe (primary) will be closest to front of vehicle.(right side of backing plate.) Larger shoe to rear. Seen them put on backwards many times when changing from one side to the other. If you only took picture of drivers side, and your using that for reference, adjuster, shoes etc, will be wrong when you go to opposite side of truck. What year is this truck?

if i had a picture ,its worth a thousand words .

Good afternoon! Ive got you covered on this one! Have a great weekend!! I have enclosed figures for the diesel engine,the 8 valve gas and 16 valve gas. yours should be the 16 valve configuration as you will see in the figures.

try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

A manual will have pictures and everything.
Just replaced mine. Five bolts in bracket holding tension idler, A/C compressor (if applicable) and power steering pump must be removed to access 3 bolts in water pump. Just push aside enough to access remaining bolts. Email at [email protected] if additional info is needed. Also, diagram serpentine belt before removing. Took me at least 15 attempts and 20 minutes to figure out

i always get a chiltons manual from any local auto part stores. its a book that shows step by step instuctions to do about anything to your car.