Question about 2001 Kia Optima

1 Answer

No fuel after replacing fuel pump all fuses are good no power to fuel pump

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 255 Answers

Check with test light at pump,
check wireing for break.

Posted on Sep 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse box diagram


Make sure the ground is good, that truck was known for a bad connector near the Trannie cross member. Find your plug at fuel pump,4 wires..2 black, gray and purple. Black and purple are for the float. Gray is power to pump, black with yellow is ground for pump. When key is turned grey wire gets power check good ground . If power and grounds are good replace pump if not fix ground or replace relay

Jan 27, 2014 | 1998 GMC Jimmy

1 Answer

No power to fuel pump 1997 s-10 blazer


Have you checked for continuity from the fuel pump fuse to the pump do this with the ignition off, you may have a break in the live cable, or take a voltmeter and check voltage at the pump.

Jan 06, 2013 | 1994 Chevrolet S-10

1 Answer

No power to fuel pump on a 1993 ford probe. all fuses are god,fuel pump relay is good and fuel cut of switch is good as well but still no power to pump?


If you actually have no power to the pump and all the fuses and relays are good check the wires for a short and if that is good replace the ignition switch. If you think the condition is no power to the pump because it doesn't seem to power up remove the pump and apply direct power to it to see if the pump is the problem.

Oct 10, 2011 | 1990 Ford F150

1 Answer

Fuel Pump Problem - checked-up the relay and found good; fuse good but still no power going to the fuel pump.


Use a multimeter to make sure wire to fuel pump hot, if it is its the fuel pump failure. Also check voltage at relay if it has power, also replace fuse just in case.

May 02, 2010 | 1997 Mercury Villager

3 Answers

No power to fuel pump car was running fine just quit repalced fuel pump no power to pump, car will start when spraying starting fluid in to intake, is there a fuse ? also replaced ECM, fuel filter,...


Check for 12 volts power at the fuel pump harness. If no power is going to the pump, check the fuel pump relay. Also, check the fuel pump inertia switch. Ford usually has it on either inside left or right rear trunk fenders.

Apr 09, 2010 | 1987 Ford Taurus

1 Answer

Fuel pump replacement


How to Replace a Fuel Pump

Parts:
1. Fuel Pump - $51.16

ff89027.jpg

DELPHI, ELECTRIC FUEL PUMP -- Meets Or Exceeds OEM Quality, Matches The Genuine Fit And Function

Tools:
1. 3/8 in. Drive Ratchet
2. Floor Jack
3. Multimeter
4. Jack Stand Set
5. Flat Head Screwdriver
6. Mallet Hammer
7. Socket Set

Steps:
Step 1 * Locate the fuel pump.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 * Have a friend turn the key to the“ON” position while you listen for a high pitched hiss/whine coming from the electric fuel pump.
o Tip: If the fuel pump is located in the fuel tank, you can open the fuel cap and listen to hear the fuel pump. The fuel pump should run (priming the system with fuel) for a couple of seconds. Once it stops, you should be able to start the vehicle.

Step 3 * If the fuel pump does not make a sound (run and prime the fuel system) check to see if there is a fuse that supplies power to the fuel pump and check its location.
o Tip: Check the owner’s manual for location of the fuse box and fuel pump fuse.

Step 4 * Once you have found the location of the fuel pump fuse, remove the fuse from its housing and check to see if it is blown.
o Tip: A blown fuse will usually have a metal strip connecting both tabs that“blows out” (the wire looks as if it has been chopped in half or broken).

Step 5 * If you noticed that the fuse was blown, replace the fuse with a new fuse of the same amperage and repeat step 2.

Step 6 * If the fuel pump now works, you do not need to replace it. However, you will need to find what caused the fuel pump fuse to blow. We strongly recommend that this is done through a certified shop, unless you have the tools and knowledge to test electrical systems and diagnose more in depth problems.

Step 7 * If the fuse wasn’t blown, it should be checked for power and ground at the fuel pump. If there is power and ground present then you will need to replace the fuel pump.
o Tip: On most vehicles you may need to lower the fuel tank to access the power and ground leads for the fuel pump.

Step 8 * Siphon or drain as much fuel as possible from the fuel tank. Disconnect any possible fuel lines from the fuel tank.

Step 9 * Remove any retaining straps or bolts holding the fuel tank to the frame.
o Tip: You may be able to access the fuel pump from the bottom of the back seat or the trunk of the vehicle.

Step 10 * Using a digital multi meter, turn the key to the“ON” position and check for power at the fuel pump. Touch the negative lead from the DMM to a good ground and the positive lead of the DMM to the power cable at the fuel pump. You should have a reading that is equal to battery power. If you do not have a reading at all, you will need to inspect the power side of the fuel pump.
o Tip: With the ground lead of the DMM still connected to a good ground, touch the power lead to the positive side of the battery, to each side of the fuse, and again to the fuel pump. Wherever you notice the voltage reading goes from battery voltage to 0 you will need to replace whatever wires and fuse are in between.

Step 11 * If you have noticed that the power and ground being supplied to the fuel pump are both good, then you will need to replace the fuel pump.
o Tip: To check for a good ground, place the negative lead from the DMM to the ground side of the fuel pump, and the positive lead of the DMM to the positive side of the battery. If the reading on the DMM is battery voltage then you have a good ground.

Step 12 * Remove any retaining rings or bolts that hold the fuel pump in the fuel tank.

Step 13 * Remove any electrical connections or fuel lines connected to the fuel pump. Replace the fuel pump.
o Tip: If equipped, inspect and replace strainer as needed.

Step 14 * Use reverse procedure to install fuel pump and assemble all components back to their original state.

Step 15 * Start the vehicle to verify repairs.


Good job (remember rated and comment this help).

Mar 03, 2010 | 1997 Nissan Pathfinder

1 Answer

Replaceing fuel pump


How to Replace a Fuel Pump
DIY & Save up to $219.24 (Complexity: Hard / Time: 3.2 hours)

Parts:
1. Fuel Pump - $140.07

Tools:
1. 3/8 in. Drive Ratchet - $7.55
2. Floor Jack - $145.54
3. Multimeter - $247.13
4. Jack Stand Set - $36.93
5. Flat Head Screwdriver - $3.14
6. Mallet Hammer - $6.83
7. Socket Set

Steps:
1 Locate the fuel pump.
- Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
2 Have a friend turn the key to the“ON” position while you listen for a high pitched hiss/whine coming from the electric fuel pump.
- Tip: If the fuel pump is located in the fuel tank, you can open the fuel cap and listen to hear the fuel pump. The fuel pump should run (priming the system with fuel) for a couple of seconds. Once it stops, you should be able to start the vehicle.
3 If the fuel pump does not make a sound (run and prime the fuel system) check to see if there is a fuse that supplies power to the fuel pump and check its location.
- Tip: Check the owner’s manual for location of the fuse box and fuel pump fuse.

4 Once you have found the location of the fuel pump fuse, remove the fuse from its housing and check to see if it is blown.
- Tip: A blown fuse will usually have a metal strip connecting both tabs that“blows out” (the wire looks as if it has been chopped in half or broken).

5 If you noticed that the fuse was blown, replace the fuse with a new fuse of the same amperage and repeat step 2.
6 If the fuel pump now works, you do not need to replace it. However, you will need to find what caused the fuel pump fuse to blow. We strongly recommend that this is done through a certified shop, unless you have the tools and knowledge to test electrical systems and diagnose more in depth problems.
7 If the fuse wasn’t blown, it should be checked for power and ground at the fuel pump. If there is power and ground present then you will need to replace the fuel pump.
- Tip: On most vehicles you may need to lower the fuel tank to access the power and ground leads for the fuel pump.

8 Siphon or drain as much fuel as possible from the fuel tank. Disconnect any possible fuel lines from the fuel tank.
9 Remove any retaining straps or bolts holding the fuel tank to the frame.
- Tip: You may be able to access the fuel pump from the bottom of the back seat or the trunk of the vehicle.

10 Using a digital multi meter, turn the key to the“ON” position and check for power at the fuel pump. Touch the negative lead from the DMM to a good ground and the positive lead of the DMM to the power cable at the fuel pump. You should have a reading that is equal to battery power. If you do not have a reading at all, you will need to inspect the power side of the fuel pump.
- Tip: With the ground lead of the DMM still connected to a good ground, touch the power lead to the positive side of the battery, to each side of the fuse, and again to the fuel pump. Wherever you notice the voltage reading goes from battery voltage to 0 you will need to replace whatever wires and fuse are in between.

11 If you have noticed that the power and ground being supplied to the fuel pump are both good, then you will need to replace the fuel pump.
- Tip: To check for a good ground, place the negative lead from the DMM to the ground side of the fuel pump, and the positive lead of the DMM to the positive side of the battery. If the reading on the DMM is battery voltage then you have a good ground.

12 Remove any retaining rings or bolts that hold the fuel pump in the fuel tank.
13 Remove any electrical connections or fuel lines connected to the fuel pump. Replace the fuel pump.
- Tip: If equipped, inspect and replace strainer as needed.

14 Use reverse procedure to install fuel pump and assemble all components back to their original state.
15 Start the vehicle to verify repairs.

Hope helps with this (remember rated this help) Good luck.

Feb 09, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

No main engine fuse, fuse pump fuse


this model dont have fuel pump fuse , the ecm supply power to pump, check EFI fuse 15amp , if good, then remove rear passenger seat, to check the fuel pump , give me for notice please

May 03, 2009 | Lexus ES 300 Cars & Trucks

1 Answer

New relay an new fuel pump no fire goin to fuel pump


Check fuel pump fuse, remember fuse send power to relay and relay sends power to pump, Check power wires to pump and make sure FUEL PUMP FUSE IS GOOD if not replace and take care of this problem. Good luck and thanks for using FIX YA.

Mar 25, 2009 | 1990 Ford F150

1 Answer

Do you know where or if a 2000 Mazda 626 has a fuel pump cut off switch. According to the parts store it doesn't have a fuel pump relay. I have replaced the fuel pump and the car still won't crank. I am...


Hello, I am going to make a few assumptions here. The vehicle has an electric fuel pump and you replaced it. The vehicle has fuel injection. The engine is actually cranking, just not starting, when you say "car still won't crank". You are getting fire to the spark plugs at the plug ends. You checked the fuel pump for power at the pump. No power, then you back traced the wire to the fuse block and checked the fuse to see if it was blown. If the fuse is good back trace the power to the ignition switch and/or ECM for power. You have power at the pump, check the ground and make sure it is connected properly. Will the pump run when someone turns the key on? Pump runs, check fuel manifold for pressure. No pressure, check the fuel filter for blockage, or replace it. Fuel pump doesn't run, new replacement pump is defective. There is usually some type of control module for the fuel pump on fuel injected vehicles. Good Luck, RAC

Mar 24, 2009 | 2000 Mazda 626

Not finding what you are looking for?
2001 Kia Optima Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76070 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...