Question about 2003 Hyundai Tiburon

1 Answer

Wheel bearing how do you take off front wheel bearing on a 97 hyundai elantra

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,280 Answers

The front 'hub' bearing is 'pressed' out. You have to remove the steering knuckle from the vehicle and using a hydraulic press, replace the bearing by pressing out the old one and then pressing in the new one.

Posted on Sep 07, 2009

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 187 Answers

SOURCE: front wheel bearing

This job is more than a none mechanic is able to do easily.

Posted on May 09, 2009

  • 171 Answers

SOURCE: how to replace 2002 hyundai elantra hub and bearing

With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Posted on Apr 09, 2010

johnjohn2
  • 5763 Answers

SOURCE: how expensive is it to replace front wheel

It all depends where you live, the rate in ct is about 95.00 per hour and the time to replace a wheel bearing on this car is about two hours per side plus the parts and an aglinment,so it would cost about $400.00 in labor and the parts are not much, i would say for a good bearing about $30.00 and then the alignment which is about $69.99, you should shop around and try to get the best price. these bearings need to be pressed out and the new pressed in, heres a picture of the bearing , theres one on wheel, hope this is helpful.johnjohn2_70.jpg

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 04 hyundai elantra. When im driving slow (0-40mph) you can hear a grinding noise coming from the front driver side, but when i speed up on the highway or anything there is no more noise. it


This could be the brake pads dragging or it could be a wheel bearing. You can check one or the other. The wheel bearing is tested by jacking up the car with that wheel off the ground and see if you can rock the wheel side to side or up and down. The way to check the brakes is to take the wheel off and look at the brake pads.

Sep 14, 2014 | 2004 Hyundai Elantra

1 Answer

Diagram of front passenger wheel bearing on 2002 hyundai elantra gt


BETTER GET THE SERVICE MANUAL,IT WILL BE EASIER FOR YOU TO UNDERSTAND THE DIFFERENCE.

Mar 12, 2014 | Hyundai Cars & Trucks

1 Answer

How expensive is it to replace front wheel bearings on a 2003 hyundai elantra?


It all depends where you live, the rate in ct is about 95.00 per hour and the time to replace a wheel bearing on this car is about two hours per side plus the parts and an aglinment,so it would cost about $400.00 in labor and the parts are not much, i would say for a good bearing about $30.00 and then the alignment which is about $69.99, you should shop around and try to get the best price. these bearings need to be pressed out and the new pressed in, heres a picture of the bearing , theres one on wheel, hope this is helpful.johnjohn2_70.jpg

Feb 26, 2011 | Hyundai Motor 2003 Elantra

1 Answer

Ok so i have a 1998 1hyundai elantra and i was switching the front pessange wheel bearing but i cant get the old one out. The whole bearing isnt in the housing its just the outside edge, any ideas on how...


The wheel bearing on that one is pressed in. You will need to pull the knuckle and bring it to a machine shop or auto repair shop to have the old bearing pressed out and the new bearing pressed in.

Oct 01, 2010 | 1998 Hyundai Elantra

1 Answer

How to replace 2002 hyundai elantra hub and bearing


With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Apr 09, 2010 | Hyundai Motor 2002 Elantra

1 Answer

Front wheel bearing


This job is more than a none mechanic is able to do easily.

May 09, 2009 | 1998 Hyundai Tiburon

1 Answer

Bearing trouble


Ouch, get your wheel bearings checked. I had a 97 Hyundai and in the 3 years I had it, the front bearings had to be replaced twice and the rear once once.

Sep 28, 2008 | 1997 Hyundai Accent

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...