Question about 1998 Volvo V70

Open Question

Need to change inner tie rod ends on 2002 V70 T5 volvo

Any advice on changing these out would be greatly appreciated.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change power steering pump


Play in the steering wheel is likely from worn tie rod ends. Have your inner and outer tie rods checked. The outer tie rods are connected to the rod ends coming out of the rack on each side, and are connected to the wheels. The inner tie rods are not visible-but are on the rods under the protective boots on each end of the rack and pinion assembly.
You may need a new rack assembly, but first check if you just need new tie rods.

Nov 25, 2013 | 1997 Honda Accord

1 Answer

2002 FORD TAURUS INNER TIE ROD END


They screw on & then are cripped with a special tool

Dec 24, 2012 | 2002 Ford Taurus

1 Answer

MY VOLVO V70 HAS A SHUDDER BETWEEN 40 / 50 MPH , BUT IT IS NOT WHEEL BALANCE


brake rotors could be worn out.could have loose worn wheel bearings.could have worn tie rod ends or worn ball joints.

Oct 14, 2012 | 2003 Volvo V70

1 Answer

Inner tie rod removal


The first step in replacing the inner tie rod is to remove the tie rod end. It's basically a three step process, where you start by loosening the jam nut that's used to set the alignment (toe-in or toe-out). That jam nut determines how far up the inner tie rod the tie rod end is fixed. The tie rod end is hollow and threaded, so it can be screwed on or off the inner tie rod. Any procedure for removing a tie rod will start by telling you to count the turns you unscrew the tie rod end, something that I didn't do, and I'll save the explanation for the end:-) After you loosen the jam nut, you remove the cotter pin from the post on the outer tie rod ball joint, and unscrew the nut that holds the ball joint into the tapered fitting on the steering knuckle (video to right). After you pop the outer tie end free of the steering knuckle, you can unscrew the tie rod end. from the inner tie rod, but you need to grip it with something. Inner tie rods normally have some flat surfaces or a splined surface for grabbing with pliers. In this case, I needed two pairs of visegrips and a clamp to hold the visegrips on the inner tie rod from moving in order to get the outer tie rod end broken free and turning easy. That video is below. I happen to own the shop manuals for my Dodge Omni, so I was able to study the procedure for replacing the inner tie rod in detail. I didn't follow it for a couple reason. First, they show my type of power steering rack (Saginaw vs TRW) needs to be removed from the car to change the inner tie rod. That's a lot of extra work, not to mention the fact I buried one of the crossmember bolts in my unibody and flooring repair! So I went with an inner tie rod removal kit from Harbor Freight, manufactured by U.S. General (in Taiwan). The tool is very simple, basically a large steel tub with a snap in opening for a large crows foot insert on one end and a 1/2" socket drive on the other end. The kit is shown in the photo to the lower left (which I need to replace), and a video of the procedure is shown below. The kit wasn't quite right for my car, I had to use an oversized crows foot and the ball joint housing on the inner tie rod was too long, so the flats on the housing were barely held with the crows foot positioned by hand at the very end of the tool. But I got it out.

Dec 16, 2010 | 1992 Buick LeSabre

1 Answer

Front end shakes upon acceleration


when you accelerate the torque(twisting motion)is lifting the front of the car(hence wheelspin), taking the weight off the lower control arms(no weight = more movement)so when you coast, the full front end weight is on the front suspension = no shake....

Apr 25, 2010 | 1998 Volvo V70

1 Answer

Impact bent the right front tie rod. how can it be removed for straightening or replacing?


First loosen the jam nut with a 21mm wrench. Then use vise grips or whatever you have to make sure the rod can be turned that goes into the outer tie rod. Then remove the cotter pin and 17mm castle nut. Strike the hub where the tie rod goes through with a hammer repeatedly until the tie rod pops out of the hole.

Then simply unscrew the tie rod end and replace it. If the inner tie rod end is also damaged, or the rod is damaged you will need to replace them as well. Inner tie rods have a special tool to remove them, see your local auto parts store.

Remember, replacing an outer tie rod end changes your cars toe (alignment). You will require an alignment after replacing it, even if you think the car drives straight.

Good luck!

Nov 30, 2009 | 2002 Hyundai Accent

1 Answer

Replacing outer tie-rods on '98 volvo v70 wagon


try www.autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 18, 2009 | 1998 Volvo V70

1 Answer

Inner tie rod ends on a 2002 toyota celica


First, you do NOT have to remove the rack to replace the inner tie rod ends. Second, If you want a .pdf regarding the procedure, I'll be glad to send it to you. But, the tie rods just screw off. Whatyou WILL need to do is get a good front-end alignement after you replace the inner tie rod. If not, you will destroy your tires. Alignment is critical to minimize tire wear on Celicas.

Nov 12, 2008 | 2002 Toyota Celica

Not finding what you are looking for?
1998 Volvo V70 Logo

Related Topics:

171 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...