Question about 2000 Oldsmobile Intrigue

Open Question

How do you replace harmonic balancer on 2000 intrigue? are there any special tools needed ?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 oldsmobile crank sensor 3800 where is it


The sensor is on the front of the engine just to the side crankshaft harmonic balancer.It is very hard to get at and requires special tools to replace it properly.

Sep 21, 2011 | 1999 Oldsmobile Intrigue

1 Answer

Replace harmonic balancer 1996 mitsubishi 3000gt


mcdevito75 here, You"ll need speciall tools for this job, let your local shop do the job.

Jun 16, 2010 | 1996 Mitsubishi 3000GT

1 Answer

How to remove the dampening ring on a 1989 dodge dynasty. Iam replacing the water pump


there is a special harmonic balancer puller (and i do mean special) don't use a regular one or you will messup the harmonic balancer you can rent the tool at autozone it's free rental,,, they charge you for the tool but you get your money back when you return the tool works great

Feb 25, 2010 | 1989 Dodge Dynasty

1 Answer

How do you replace the harmonic balancer pulley on the 2000 oldsmobile intrigue


The short answer to your question is:

1. Raise the car on the passenger side and remove the front wheel.
2. Remove the belts on the harmonic balancer.
3. Remove the retaining bolt.
4. With a puller, jack the harmonic balancer off of the crank shaft. You can rent a puller at your local auto parts store. It is easiest to access the harmonic balancer through the fender, hence the need to remove the wheel.
5. You should also consider replacing the seal around the harmonic balancer to minimize the possibility of a leak later.
6. Install the new harmonic balancer and tighten the retaining bolt to the specified torque (I don't know this off the top of my head).
7. Replace the belts and wheel, and voila...mission accomplished.

This was a short answer to your question. You may wish to consult a repair manual for illustrations, torque specifications, additional instructions, etc. This job is not for the faint of heart. Good luck!

Feb 19, 2010 | 2000 Oldsmobile Intrigue

1 Answer

My Harmonic balancer is spaced about .25 inch off cars wall. 2000


There are special tools required to remove and install the damper. I would recommend a mechanic do the job that has the tools also it has to be tightened and loosened and re tightened in a certain way. The labor guide is 1.1 hours so don't be over charged. enjoy

Feb 15, 2010 | 2000 Ford Crown Victoria

2 Answers

Where is the crank sensor located on a 1999 oldsmobile intrigue 3.5 engine???? easy to replace or not...


usually all crankshaft sensors are located right next to the main drive pulley (Harmonic balancer). As far as being easy is concerned some are not so easy as some require the removal of the harmonic balancer to get to it.. but you might be lucky Gm is pretty good at making the Crankshaft sensor accessible without removing the harmonic balancer.

Dec 01, 2009 | Oldsmobile Intrigue Cars & Trucks

1 Answer

Crankshaft Position Sensor and Camshaft Position Sensor


REMOVE OR DISCONNECT

  1. Serpentine belt from the crankshaft pulley.
  2. Raise the vehicle on a hoist.
  3. Right front tire and wheel assembly.
  4. Right inner fender access cover.
  5. Using a 28 mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Crankshaft harmonic balancer using tool J 38192 or equivalent.
  7. Sensor electrical connector.
  8. Foreign object deflector.
  9. Sensor and pedestal from block face.
  10. Sensor from pedestal.
INSTALL OR CONNECT:

  1. Loosely install the crankshaft sensor on the pedestal.
  2. Position the sensor with pedestal attached on special Tool J 37089.
  3. Position the special tool on the crankshaft.
  4. Bolts to hold the pedestal to the block face, torque to 20-40 Nm (14-28 lb.ft).
  5. Torque the pedestal pinch bolt to 3-4 Nm (38-40 lb.in).
  6. Remove special tool J 37089.
  7. Place the special tool 37089 on the harmonic balancer and turn. If any vane of the harmonic balancer touches the tool, replace the balancer assembly.
  8. Balancer on the crankshaft.
    • Apply thread sealer (GM 1052080) or equivalent to the threads of the balancer bolt.
  1. Torque the crankshaft bolt to 140 Nm + 56°(104 lb.ft + 56°).
  2. Foreign object deflector.
  3. Electrical connector.
  4. Inner fender shield.
  5. Tire and wheel assembly, torque to 140 Nm (104 lb.ft).
  6. Lower the vehicle.
  7. Serpentine belt.

Jun 02, 2009 | 1994 Buick Regal Gran Sport

1 Answer

How to remove and replace harmonic balancer on 1990 honda accord 2.2 engine


You need a special tool to hold the harmonic balancer with while you break the center bolt loose. Once loose, should wiggle off.

Mar 07, 2009 | 1990 Honda Accord

4 Answers

Mitsubishi Eclipse Harmonic Balancer 3.0L Removal


There is a panel inside the wheel well that you can take off that gives you perfect access to the harmonic balancer. A special tool is required. i had my dad make one because he has access to whatever he needs at the factory. but you can get them at the dealer. i have no clue how much they cost. I can't see any way of doing it without the special tool. after you get the tool its pretty simple to get off. it takes alot of force to break the bolt loose though. i used the handle off my jack as a cheater bar. hope this helps...

Jan 08, 2009 | 2000 Mitsubishi Eclipse

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...