Question about 2006 Ford Merkur Scorpio

Open Question

Mondeo tdci 52 plate had flywheel changed and now it cutts out when hot ive been told its sensor

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ive got ford mondeo tdci 54 plate.. ive just had the dual mass flywheel replaced but now the clutch is playing up it goes stiff and wont go into gear, could this be it needs clutch fluid??


Angela, I'll be honest I'm confused. It shows "problem with Toytoa Celica" but you mention a Ford Mondeo in your post. Just to be sure we're talking about a Ford Mondeo that had the flywheel replaced, correct? Chances are if they replaced the flywheel you normally would always replace the clutch disk with it. If this is a hydraulic clutch system you don't typically have to open the hydraulic system to swap out the flywheel and clutch on a car. This would lead me to believe clutch fluid isn't your answer, but I would at least make sure you check it. If they DID have to open the system the clutch needs to have the air bled out of the hydraulic lines.

Nov 24, 2012 | 2002 Toyota Celica

2 Answers

I have a 53 plate mondeo ghia X 130bhp tdci modelwith approx 145K miles on the clock. It has been cutting out when driving,twice today on the way to work & on the way back! Just been serviced,new...


Ive a 03 mondeo ghia x, 2l tdci,130bhp have then same cutting out problem, had new battery, new injectors and recoded still the problem is there any1 no y, diognostics test done which was injectors but still no luck same as b4

Mar 29, 2012 | Ford Mondeo Cars & Trucks

1 Answer

Hi there how do i take the fly wheel and pressur-plate off my 1997 ford mondeo engine i finding it hard how ive takeing gearbox off. hope you can help thanks


after you remove the gearbox the clutch pressure plate normally unbolts from the flywheel then the flywheel unbolts from the crankshaft...........hope this helps............cheers.

Jul 08, 2011 | Ford Focus Cars & Trucks

1 Answer

MONDEO TDCI 2.0L CUTS OUT UNDER ACCELERATION AND THE DEISEL PLUG LIGHT FLASHES.ENGINE RESTARTS IMMEDIATELY.NEW CLUTCH AND FLYWHEEL SENSOR FITTED RECENTLY


There has to be a loose connection somewhere. Being pulled apart under hard acceleration. Do you have any OBDII codes stored? This will lead you to your fault. Hope this helps...

Mar 10, 2011 | Ford Taurus X Cars & Trucks

2 Answers

Dual mass fly wheel


did u git the timin rite-now the flywheel fits as replacement correct-do u hav a repair manual!

Aug 16, 2009 | Ford Focus Cars & Trucks

1 Answer

Will a 2003 mondeo tdci engine fit into a 2002 mondeo tdci


They should be. The SVT Models stay Very Consistent on the Motors.

Jan 21, 2009 | 2002 Ford SVT Focus

1 Answer

Mondeo tdci


hi there, you will need a diagnostic check carried out to locate the exact fault, most garages have the equipment to carry out these checks so you won't need to visit your ford agent, a common fault on the engines is the camshaft sensor these cost around £20 and are very easy to replace, however once you have it tested you will now your exact fault, hope this helps

Oct 23, 2008 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...