Question about GMC Sierra 1500

1 Answer

1997 gmc sierra 5 liter 2wd pickup steering column switch[directionals,hazzards,etc]not functioning. IS replacing it DIY a tough job?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 144 Answers

FOR THE DIY IT IS A RELATIVELY EASY TASK. THE STEERING COLUMN COVERS WILL NEED TO BE REMOVED FOR ACCESS TO SWITCH. THESE SCREWS ARE LOCATED IN BOTTOM OF LOWER COVER. HOPE THIS HELPS!!

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The audio controls and the horn will not work on my steering wheel of my 2005 gmc sierra 2500 hd


Wiring in the steering column to the switches in the steering wheel may be compromised, or the switches are possibly faulty and will have to be replaced. This is not a job for the DIYer as there is a real hazard messing with the air bag in the wheel.

Jul 31, 2017 | GMC Cars & Trucks

2 Answers

Where is the bcm located in a 97 gmc Sierra?


Try searching "bcm location GMC Sierra 97"

Jun 16, 2015 | 1997 GMC Sierra

1 Answer

2009 GMC Sierra horn started honking on it's own


the split ring in steering column is a ground to horn relay if wire touch ground or pad is compress horn will be active
hope it helps

Mar 31, 2014 | 2008 GMC Sierra 1500 2WD

1 Answer

Cruise control does not work on my 97 chevy 1500 pickup truck


No it would not be a fuse, the cruise is not fused directly.

Mar 22, 2012 | 1997 GMC Sierra

1 Answer

I need an Illustrated Parts Break down for a 1989 GMC Sierra 1500. 350 w/ PS/PB loaded. Steering column Removal Repair or Replace


Hi.

Below you get all the parts breakdown for GMC Sierra 1500, including steering column assembly:

1500 SIERRA

Here diagrams for all 1989 GMC trucks.

If you need to take apart the steering column you will also need wiring. below the color codes and wiring tips:

GMC SIERRA 1988-2005 VEHICLE WIRING

Regards.

Ginko

Aug 31, 2011 | GMC C1500 Cars & Trucks

1 Answer

How to replace ignition key in 1997 gmc sierra 2500,,tack and speedo don't work but all other gauges work


for the ignition key you have to take off the two plastic covers on the steering column. (three torx screws) remove the ignition switch and it is righ there. your speedometer has a direct cable into the transmission and should be a fairly easy repair

Sep 17, 2009 | 1997 GMC Sierra

1 Answer

Air bag light won't go off


It likely is a bad passenger air bag. Did you try switching it back to off on the switch,and unhooking the battery for 5 minutes.

May 30, 2009 | 1997 GMC Sierra

1 Answer

1997 GMC Sierra Ignition Switch Replacement


take off the cover on the top and bottom of the steering column just behind the wheel. pop the tilt lever out simply just by grabbing it and give it a good tug. then once you have the new switch and you get in there your going to need an inverted torx socket to remove the small bolts that hold the switch to the column. do not move the gear on the new switch make sure it lines up exactly as the old one did!!!!!!!!!!!!

Feb 16, 2009 | 1997 GMC Sierra

1 Answer

Diagram for replacing an ignition switch for 1998 gmc pickup


>>>>FIRST disable the air bag system
You'll need to remove the upper and lower steering column covers.
Also all the trim under the drivers side, kneee bolster, etc...
The ignition switch has 2 screws holding it on.
Remove those screws and all related wiring harness.
Then the switch.
Here is the procedure from GM......

Place the multifunction lever in the center or the OFF position.
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.

Disconnect the battery negative cable.
Disable the SIR system.
Remove the steering wheel inflator module.
Remove the horn plunger contact.
Remove the steering wheel.
Remove the tilt wheel lever.
Remove the ignition lock cylinder. Remove the upper steering column trim cover.
Couldnt find a diagram. Hope this helps.

Jan 01, 2009 | 1998 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...