Question about 2004 Lexus RX 330

1 Answer

How to replace the right rear tail lightbulb rx330

I am able to get into the assembly box to replace the tail light but can't locate where the bulb is to replace...right rear tail light

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,111 Answers

Can you not see the bulb itself i believe they come out through the back

Posted on Sep 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear turn signal probem


Have you done any mods lately? Are you using the correct replacement bulbs? Make sure the wiring is not crossed.

Feb 02, 2015 | Cars & Trucks

1 Answer

How can I take off the tail light assembly to replace the bulb for the left tu


Open the trunk. In the left corner where the lamp assembly is, you should see two screw covers that cover the screws holding in the lamp assembly.

12_5_2012_6_45_21_pm.jpg

Remove these covers to find the screws, and unscrew them to pull the taillamp assembly out of the vehicle body. Disconnect the lamp wiring harness, turn the bulb socket counterclockwise to pull out the socket, revealing the light bulb. Then pull the bulb right out of the socket and replace it with a new bulb.

Replace the socket, turning it clockwise. Replace the taillight assembly. Check that the taillamp assembly tab, located at the bottom of the taillamp assembly, is aligned to the facia bracket before securing the screws.
12_5_2012_6_46_06_pm.jpg


Screw the taillamp assembly back into the vehicle body and replace the screw covers. Check to make sure the new bulb works properly.

Your owners manual specifies that the rear left turn lamp is a lamp with bulb number 3057K. You should be able to find them at any automotive store or from your dealer. Hope this helps.

Dec 05, 2012 | 2011 GMC Terrain

3 Answers

Tail lights do not work on a 2000 lexus rx 300 bulbs are fine, all other lights work fine


You may have a fried fuse. Look in your owners manual to find out which fuse it is in the fuse box diagram. If that is the problem make sure to use the same amperage fuse to replace the burned one with. I fried fuse is usually a sign that you have a short somewhere. But they can also fry for other reasons such as excess moisture somewhere. Sometimes they just burn from age and fatigue. It may solve it to just replace the fuse, but if there really is a short, the new fuse will fry too.

Dec 29, 2010 | 2000 Lexus RX 300

1 Answer

How to replace tail light on VW golf mk5 estate


Although you posted this question under a 03 VW Golf and you have a MKV. The best I can do is a MKIV set up. From the rear trunk there are access ports just for this job. The right port will be just above the light housing you will find a wire harness for the right assembly. Follow the harness and it will lead you to the assembly. Once located you can squeeze the two tabs and pull the circuit board where the bulbs are installed. Push on the bulb and twist anti-clockwise then pull out of the socket.

The left should be the same procedure and it is located behind your audio components.

NOTE: It's a good idea to wipe your hand and the glass bulb, leaving oily residue will cause early bulb failure once in operation.

May 30, 2010 | 2003 Volkswagen Golf

1 Answer

Left brake light dont work when brake peddel is applied


Replace the bulb,
1. Open the lift gate on the rear of your Blazer or drop it if you have the tail gate that folds down. Locate the screws on the inner edge of the lift gate frame. There are two screws--remove them with a Phillips screwdriver.
2. Slide the taillight assembly out of the rear of the truck, being careful to not break the locating tabs on the rear of the housing. Locate the bulb sockets on the rear of the taillight assembly.
3. Rotate the light bulb socket counterclockwise about a quarter turn to unlock it from the taillight assembly. Pull the socket straight out of the assembly with the bulb attached to it.
4. Remove the bulb from the socket by pulling it straight out of the socket. If you are removing the entire assembly from the truck, remove the remaining sockets from the rear of the taillight assembly, lay them aside and remove the assembly completely.
5. Reinstall everything in revers and don't for get to *** some grease to your socket before you place the new bulb in place and test the operation of the new bulb before you reinstall the tail light.
Thank you for using fixya and here is the bulb you need for the trail light.The 1999 Blazer uses a 3057 bulb available at most auto parts stores.

Apr 29, 2010 | 1999 Chevrolet Blazer

2 Answers

Replaced a rear tail light bulb and the warning light that indicates the bulb was bad has not reset and gone off


how do you remove the right tail light assembly in order to replace the top right bulb

Jan 23, 2010 | 2001 Lexus LS 430

2 Answers

How to replace right rear stop and tail light?


Should have acsess to lightbulbs in trunk of car.

Open trunk and remove any carpet or cover around light area.

Bulb should be in a socket,turn socket until it comes out of light lens.

Jan 11, 2010 | 2002 Jaguar X-Type

2 Answers

How do you change a brake light in a 97 accprd?


1. Open the trunk and remove the taillight cover by turning the knob.
2. Determine which of the two bulbs is burned out: tail/stoplight or turn
signal.
3. Remove the socket by turning it one-quarter turn counterclockwise.
4. Remove the burned out bulb from the socket by pulling it straight out of its socket.
5. Install the new bulb in the socket.
6. Reinstall the socket into the light assembly.
7. Test the lights to make sure the new bulb is working.
8. Reinstall the taillight assembly cover.

Nov 14, 2009 | 1997 Honda Accord

1 Answer

How to access tail light bulb in 2005 ford f-150


Drop the tailgate, on the inside of bed where tailgate closes are couple of screws.These hold the light assembly in the bed. remove the screws, then remove light assembly. The light bulb can be removed from back of the tail light assembly. Check to make sure the lightbulb work before you put the tail light back together. Good luck and hope this helps and don't forget to add some grease to the light socket to prevent corrosion. 

Jun 24, 2009 | 2005 Ford F-150

2 Answers

RX 330 - Replace tail light on 2004 Lexus RX330


On the 2004 RX330 there is no access panel for the tail lights on the tailgate. This is the procedure to replace the bulbs. You will need a screwdriver that is about 6 inches long. You are going to remove the top plastic panel to access the bulbs in the tail light assemblies. Open the tailgate. While it is open, go to the left hand side and you will see where the panel wraps around the edge. You can pull this edge down a bit and when you look in you will see at least one clip where the panel holds on. You want to stick the screwdriver in and pry the white plastic clip out. You do not want to pry the panel off the clip, but rather pry the clip out of it's hole in the door. It should pop of with some prying and pulling down of the panel. Once one clip is off, you can pull the panel off by pulling down on it in in series around it's border. Sometimes a clip will pop out of it's holder, you can easily place them back in. Try to not let the panel fall off as it will be held by a wire to the small lamp. If someone can hold this panel while you replace the bulb that is best, otherwise you can unplug the wire to fully remove the panel. Unplugging it may seem a little difficult tough as the clip that holds the plug in really has to be pressed hard. Once the panel is off, you can replace the bulb by removing it out of it's socket. Find the location you want to replace, and turn the assembly holding the bulb (it wil have wires on it) slightly counter clockwise. It should then just pull out and expose the bulb. In the case of a tail light, the bulb just pulls out. Push in a new bulb and then line up the socket and twist clockwise to lock. Make sure all your clips are on the panel, plug in the wire to the panel light, and line up the panel. Press in the panel, you will feel the clips slip back in their holes. Oh yeah, you may want to check that the lights work before you put the panel back on. As well , do not handle the bulbs with your hands ( I think halogen and led bulbs are more sensitive) but is good practice anyway for all bulbs. Hope this helps. Worked for me!

Jan 16, 2009 | 2004 Lexus RX 330

Not finding what you are looking for?
2004 Lexus RX 330 Logo

1,419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...