Question about 1992 Mazda 626

Open Question

What does it mean when the word hold comes up near the podometer

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do i have to reprogram saab 2.2 remote battery


I presume you mean you have changed battery in key.If so just hold key near door aqnd press button for a few seconds and should resetr itself

May 01, 2014 | Saab 9 3 Cars & Trucks

1 Answer

Power indicator


Near the shifter there is a button which selects either power or economy .the power button holds the gear longer before shifting

Jun 14, 2013 | 1998 Holden VT Commodore

1 Answer

What does it mean when the "Hold" indicator light comes up?


Hi, the hold light refers to the hold button on the shifter module. It means the transmission holds the lower gear revving up the rpms and won't shift to the higher gear. Seeing the light means the button has been engaged. Push it to turn it off.........

May 11, 2011 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

94 mazda 626. whats the purpose of the "HOLD" button. And how do i shut off the "HOLD" light?


if you mean the gearbox?? then their should be a button near the gearchange or on the T shift ,try that

Aug 12, 2010 | 1994 Mazda 626

1 Answer

What does it mean when the word "HOLD" appears blinking on my dashbord, I believe it has to do with the gears


Yes the HOLD light comes on when the computer detects a malfunction with the transmission....one quick flash of the hold light means a 01 code. six quick flashes would mean a 06 code. 5 long flashes would indicate a 50...6 long flashes would indicate a 60 code. Hope this helps.

Mar 14, 2010 | 1994 Mazda 929

1 Answer

2004 Jeep Grand Cherokee. Keeps stalling, engine


P0505 means the whole Idle Control system, not only the IAM. Check all related sensors (i.e. crankshaft sensor). Check with a voltmeter direct at the connector of the IAM if you get any signal. Remove the IAM from the TB, connect him, let someone switch your ignition key to ON. The IAM need to drive in/out for a short time to find the right position. Hold the IAM near a hard part, that they cant drive out completely! If IAM works fine, check the fuel pressure, check and clean your TB ( if not done yet). If that doesn't work, come back again please

Oct 25, 2009 | 2004 Jeep Grand Cherokee

2 Answers

Noisy front wheel bearing I would like to rerplace


a hydraulic press ,or go to a recon shop ,i was knocking one out and a splinter hit my mates eye ,nearly lost his eye ,HAVE THEM PRESSED IN AND OUT

Sep 20, 2009 | 2000 Ford Windstar

2 Answers

Dash warning light has come up on my vw eos, looks kinda like a horsehoe with an exclamation mark, any ideas?


if yellow this is most likely your tyre inflation indicator warning.
this means that one or more of your tyres has defated or inflated outside expected limits (do not worry)
1. check your tyre pressures are correct.
2. switch on the engine and let light come on.
3. press and hold the reset button with the same horseshoe icon which is situated near your gear lever in the middle console after several seconds the light should go and and your tyre pressure warning system is reset and ready for any change in prssure. if this does not work consult your nearest certified VW dealer they will be happy to assist.

Sep 16, 2009 | 2008 Volkswagen Eos

1 Answer

I need to change the driver side head lamp bulb I have have never done this before


Hello, this is a easy fix. Grab the black connector with one hand and hold the black rubber part in the middle near the connection. Pull gently on the connector while holding the rubber part near the middle, your goin to feel the headligh kinda move as you pull. Its probable going to be a little hard to get off, gently wiggle the connector and pull while holding. Once the connector comes off remove the rubber boot, now you will see a small bar push down (or up) on it to release it from the lock position. The headlight will come right out, not the position of the connectors when removing the light bulb, replacement light will only go in one way. Hope this is helpful.

Jan 10, 2009 | 2001 Nissan Altima

Not finding what you are looking for?
1992 Mazda 626 Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...