Question about 1991 Peugeot 405

1 Answer

My petrol Peugeot 405 (1995) seems to be immobilised altho when I enter the code on the keypad the light goes green , turn the ignition it makes the immobilised noise and of course wont start. The battery was disconnected prior to this , also the alarm was going off until I switched it off under the bonnet. Why then is my code being accepted but the car not starting , is there a reset? IT is a 1995 even tho this site only let me choose 1991?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 49 Answers

Have you tried turning the alarm back on so that it goes off again, lock and unlock the car with your fob now, then enter the code. This is because it might still be in the standard immobiliser mode.

Posted on Dec 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot 406 1.9td will not start when the code is placed on the keypad of the immobiliser. both red and green lights are on the keypad and sometimes it will start perfect any solutions greatly appriciated?


you could try resrtting the key pad by unplugging it for 15 mins and then plugging it back in mate






if this helps let me know


cheers
big mike

Apr 30, 2011 | 1989 Peugeot 405

1 Answer

I have a peugeot partner van 1997, and I want to bye pass the immobiliser, as the van will not start. The red and green light are staying on. do you have any suggestions please? It is with a mecahnical...


Leave it for half an hour with the ignition on and door closed, it should re set (this happens when the wrong code is used for more than 3 times) check for a sticking button, sometimes they go sticky with a lot of use, if you do get the green light just umplug the keyboard when running and it disables the system. If you cannot get the green light try leaving the battery off overnight with the lights switched on then connect the battery, if still no with the ignition on and someone in the car spark the earth lead to the battery untill the green light comes on.

Apr 13, 2010 | 1991 Peugeot 405

2 Answers

Peugeot 406 hdi electronic immobiliser warning


The ignition key may be defective or in need of a battery to generate the code needed to disarm the immobilizer. Hope this helps!

Mar 05, 2010 | 2005 Peugeot 405

1 Answer

My peugeot 306 wont start with the key


hello it sound like ign switch to me if you check voltage at key swictch going in at out when you turn the key to crank if you dont see power on cramking wire then its defently the swicth the thats were i would start hope this helps Thunderboltz

Jan 31, 2010 | 1991 Peugeot 405

2 Answers

The car will not start as it seems immobiliser is a problem


could be your crank sensor has failed.

usually it is behind or near the main crank pulley, not sure on your car's exact location.

Try disconnecting the battery for 10 minutes to reset the ecu and see if it restarts.

Oct 23, 2009 | Peugeot 405 Cars & Trucks

3 Answers

Peugeot 406 hdi executive 2002 will not start


immobiliser problem main dealer me thinks

Aug 18, 2009 | Peugeot 406 Cars & Trucks

1 Answer

I have a peugeot 406 hdi executive with no handbook.The car wont start,I think i have immobiliser problem and i need to enter code into keypad.Where is the keypad located?


this car has no key pad as to new, after 1999 all pads are gone and its done through your key, is it cranking over ok, i suspect a faulty lift pump, you have to listen for a wine when you turn the key on, its the lift pump under rear seat.

Aug 16, 2009 | 2006 Peugeot 604

2 Answers

Peugeot 406 immobiliser keypad will not accept code


hi, on your keypad, when key turned on, do have the red and green light on.
if so its locked out, will not start even with correct code.
need to know that first
and diesel or petrol.
i know your car is before a 1999 what year is it

May 17, 2009 | 2000 Ford Escort

1 Answer

Wont start


Hi
Had a similar problem with my x type 2.5 petrol, only had the car 1 day went to start it nothing happend all the lights came up on the dash but the engine wouldn't start and the immobiliser light stayed on. Spoke to Jaguar they had no idea and I couldn't get it to them. After disconnecting the battery trying to reset the immobiliser phoned and auto locksmith they came out and discovered the end of the key with the blade had lost it's coding and the immobiliser was not disarming, they reprogrammed the key and the car started no problem. As far as i know there is no way past the immobiliser. Hope this helps.

Aug 11, 2008 | 2002 Jaguar X-Type

2 Answers

Citroen zx immobiliser 1400cc petrol 1996


hi i am a mechanic and i have read your problem i think it might be your EARTH STRAP

Jul 11, 2008 | Peugeot 505 Cars & Trucks

Not finding what you are looking for?
1991 Peugeot 405 Logo

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...