Question about Mitsubishi Pickup

Open Question

I need to replace the clutch on my mitsibishi L200 4x4. I normally work from a haynes manual but no such luck with this car. Any ideas? I need to know what to unbolt to get the gear box to come out?

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Removing gearbox

Here's your book info is below...
Most auto parts stores carry Haynes Manuals. You can order them from Haynes if needed. Or...often they are carried in your local library.

I have done Ford and Toyota clutches using these books. Clutch replacement is not hard, just time consuming...And easier if you have a lift.

Note: If like many vehicles, don't forget to replace the engine rear main seal while you have access with the fly wheel off.

You can call Haynes and ask specifically if the book covers the repair you are attempting. I have called them to get more specific wiring diagrams not always provided with the books. Very helpful in providing tech data... I have a Haynes manual for all my vehicles...makes maintenance and repair much easier than researching every I need to do something to my vehicles.

Best of luck finding the information you need...

Here's your book info.

Saturn S-series Haynes Repair Manual Online covering all 1991 thru 2002 models of Saturn SL, SL1, SL2, SC, SC1, SC2, SW1 and SW2
Part Number #E87010
Haynes Repair Manual Online for the Saturn S-series covering all 1991 thru 2002 models of Saturn SL, SL1, SL2, SC, SC1, SC2, SW1 and SW2 has clear instructions and hundreds of photographs to help you perform anything from simple maintenance to basic repairs. Whether you're a beginner or a pro, you can save big with Haynes!
Complete coverage for your 1991 thru 2002 Saturn S-series (SL, SL1, SL2, SC, SC1, SC2, SW1 or SW2):

--Routine Maintenance
--Tune-up procedures
--Engine repair
--Cooling and heating
--Air Conditioning
--Fuel and exhaust
--Emissions control
--Suspension and steering
--Electrical systems
--Wiring diagrams

Dec 11, 2013 | 1993 Saturn SW1

1 Answer

2007 Equinox AWD doesn't work, message "Service AWD" on the dashboard is on. Diagnostics said the rear Clutch control module is not communicating, we replaced the module, still not communicating. Now we...

I'd go here and buy the manual, and STOP throwing money at it until you actually know whats can be very expensive that way.

Nov 01, 2013 | 2007 Chevrolet Equinox LS New Cars

1 Answer

I can not find an exploded diagram to show clutch and pressure plate replacement.where can I get one for a 1988 Chevy nova 1.6 liter 5 speed manual

Try HAYNES REPAIR is a very simple job on that type of vehicle if you have
a service lift or a good set of tall ramps,,,I am sure Haynes should have it but finding the same year model Is hard to say.......But most clutch jobs on rear wheel drives arent that hard if you have the
tools and a trans jack and a good safe way to raise the vehicle................If you cant find one I will give you easy step by step instructions.......I am certified...27 yrs of service work auto/ med. heavy of luck..........................................Metalpoet

Apr 26, 2011 | 1988 Chevrolet Nova

1 Answer

I just installed a new clutch in my 2006 hhr , now it wont start, when you turn the key the vehicle doesnt do anything and the control panel flashes service air bag, and engine power low? any ideas what...

is the batt at normal charge--also inspec for any wire disconnects in the process--neutral safety switch may have issues--do you have a haynes repair manual,chiltons etc

Nov 21, 2010 | 2006 Chevrolet HHR

1 Answer

How to remove a 2006 ford mustang clutch

You need to remove the transmission. My recommendation is to buy a Haynes workshop Manual and read the how to remove and replace clutch. It isn't a hard job but you will need to lift the car off the ground so as to access the gearbox, drive-shaft etc;
Good luck

Nov 12, 2010 | 2006 Ford Mustang

1 Answer

Clutch engaging when pedal is to the floor

need to find out if there is a clutch adjustment or you have to replace it give these websites a try and if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Feb 08, 2010 | 1993 Mazda MX-3

1 Answer

My clutch will not disengage do you think I only need to replace the clutch slave cylinder? Fiat Brava w reg

yes you may even have to replace the pressure plate give these websites a try and if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Nov 07, 2009 | 2006 Fiat 124

1 Answer

I need to replace a clutch on a 1991 isuzu impulse....i need somepicture along with detailed text one else seems to offer any help.

Good luck, this isnt something I would recommend doing for the first time. If you must then purchase a Chiltons/haynes manual and it will normally cover this

Aug 31, 2009 | 1991 Isuzu Impulse

1 Answer

1991 Chevy Cavalier Transaxle removal

you need to support need haynes repair manual. you have 58 steps to remove would be easier to have repair manual.

Apr 13, 2009 | 1991 Chevrolet Cavalier

1 Answer

Mitsibishi colt 97 stuck in 1st gear

Your link broke off. What might have happened is the car got stuck in 1st, and when you shifted to second, the link broke. Not too clued up on your car, but you probably need to drop the gearbox. On some cars you can take out the shifter without having to drop the box and still see if the link is broken. Good luck

Mar 18, 2009 | 2006 Mitsubishi Colt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,022 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides