Question about 1998 Ford Expedition

Open Question

1999 Ford Expedition when removing the transfer case do you need two torsion arm tools

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW TO REMOVE A LOWER LEFT CONTROL ARM AND TORSION BAR


jack the vehicle right up so that the the wheels are clear of the floor . Place vehicle on jack stands
release the tension on the torsion bar by removing the adjuster in the arm. you may have to use Stiltons or pipe wrench to get the last bit of tension out of the bar . remove and retainers and tap the bar out of the splines.of the lower control arm. mark the bar so that you will know which spline to use for reassembly
remove the lower control arm.

Mar 02, 2015 | 2004 Ford Explorer Sport Trac

1 Answer

In a 2000 ford expedition does the cross member under the transfer case need to be removed? to take the transfer case out . if so how do I remove the bars attach to it ?


First you need to measure the height from the ground to the frame on each side on level ground. Write those numbers down. If you follow the torsion bars to the crossmember, you will see arms or levers attached to them. Counter clockwise will lower them. Remove the bolts, then the torsion bars then the crossmember.

Aug 21, 2013 | 2000 Ford Expedition

1 Answer

How difficult it is replacing a transfer case for a 1999 ford expedition and will it be cheaper than rebuilding one


yes it would be cheaper to put a used transfer case in. its definately not someting you wanna do on ramps in the driveway

May 12, 2011 | 1999 Ford Expedition

2 Answers

What is the torson bar on jimmy and where can you get the part for it?


1995-2005 Models NOTE: The following procedure requires the use of the torsion bar unloader tool No. J-36202 or equivalent.
  1. Raise and safely support the vehicle.
  2. Remove the transmission shield, if equipped.
  3. Install a torsion bar unloader tool to relax the tension on the torsion bar adjusting arm screw; record the number of turns necessary to properly install the tool. Remove the adjusting screw and the unloader tool.
  4. Unfasten the lower link mount nut from one side, then disengage the torsion bars. NOTE: Note the direction of the forward end and side of the torsion bar being removed
  5. Remove the lower link nut from the opposite side.
  6. Remove the lower link mount, upper link mount nut, upper link mount and then unfasten the torsion bar from the frame.
To Install:
  1. Install the torsion bar and support.
  2. Install the upper link mount and mount nut.
    • Tighten the nut to 33 ft. lbs. (45 Nm) on 1995-96 models and 48 ft. lbs. (65 Nm) on 1997 and later models.
  3. Place a jack under the torsion bar to release tension, then install the lower link mount bushing and nut.
    • Tighten the nut to 13 ft. lbs. (18 Nm) on 1995 models, 50 ft. lbs. (68 Nm) on 1996-98 models and 37 ft. lbs. (50 Nm) on 1999 and later models.
  4. Install the torsion bar unloader tool and tighten the tool against the adjusting arm the same number turns recorded earlier, then remove the tool. This loads the torsion bars.
  5. Install the transmission shield, if removed.
  6. Remove the jackstands and lower the vehicle.
  7. Check and adjust the Z height as outlined in the wheel alignment portion of this section.
prev.gif next.gif

Jul 08, 2010 | 1997 GMC Jimmy

1 Answer

How to replace an a/c clutch on 1999 ford expedition


go to your local auto zone they have a loan tool progam they have that specialty tool (pulley remover) they also explain to you wat you need to do

Oct 26, 2009 | 1999 Ford Expedition

1 Answer

Replacing ball joints on 1999 Ford Expedition


U CAN REPLACE JUST THE BALL JOINT OR THEY COME WITH THE ARMS.DEPENDING ON MECHANICAL ABILITY AND TOOLS IT IS MUCH SIMPLER TO REPLACE THE ARMS

May 06, 2009 | 1999 Ford Expedition

1 Answer

2001 ford expedition broken wipers?


you need to remove the wiper arms first. thay must be in the highest position for removal. take your hand and move them to that point then remove the nut cover at the base of the arm and remove the nut, a wiper arm remover tool may be required if thay dont come off easy,this tool is available at your local auto parts store.then remove the panels that sorround the wiper arm studs from which you took the wiper arms from,these panels may have little plastic screw covers on them that need to be removed to reveal the screws that hold the panels down

Jan 12, 2009 | 2001 Ford Expedition

1 Answer

Arm rest


I havent got a clue. I deal strictly with Large screen televisions. Try asking one of the other experts.

Jul 05, 2008 | 1999 Ford Expedition

Not finding what you are looking for?
1998 Ford Expedition Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...