Question about 2007 Ford Expedition EL XLT

Open Question

Sunroof not operating via overhead controls 1994 Ford Explorer. Was working prior to needing new Keys for vehicle

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there no power to sunroof and overhead console?


You need to check the relays, but the connection pigtail might have been disconnected somehow. Did you have any recent repairs to this vehicle?

Feb 14, 2016 | 2003 Ford Explorer Sport

1 Answer

2001 cadillac deville sunroof open and want close


Check the RAP fuse in the rear fuse box , this fuse powers the sunroof control module ! Fuse Block - Rear , Left rear of the passenger compartment, under the rear seat .
The sunroof module contains the logic for the opening and the closing of the sunroof. The sunroof motor assembly contains the reversible DC drive motor, the gear train, and the limit switch.
The sunroof module determines the sunroof motor direction based on inputs received from the overhead console sunroof switches. When the ignition switch is in the ON position or when retained accessory power (RAP) is active, voltage is applied to the sunroof module via the RAP relay. For a description and operation of the RAP system, refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power. The sunroof module controls the sunroof motor direction by changing the polarity of the applied voltage. The sunroof module remembers the sunroof position whenever the ignition switch is turned to the OFF position. The limit switch is used as an input to the sunroof module to indicate that the glass is fully closed, or in the comfort stop positions. The limit switch is grounded when the sunroof glass is in the fully closed or comfort stop positions, otherwise it is open.
The SLIDE CLOSE mode is initiated by moving and holding the sunroof slide switch (ROOF) forward. This applies a ground provided from the sunroof limit switch low reference circuit to the sunroof switch close vent signal input of the sunroof module. The sunroof module controls voltage to the control circuits of the sunroof motor. The sunroof motor will run until the limit switch contacts are closed. The closing of the limit switch will apply the sunroof limit switch low reference circuit to the sunroof limit switch soft stop signal circuit to the sunroof module, indicating the flush closed position has been reached. As the sunroof is approaching the close position the sunroof glass will force the wind deflector downward.
You need to have a factory scan tool hooked up an have it checked for DTC'S in the sunroof control module ! a code reader will not do this , a code reader will only check the engine codes for OBD 2 .
Important: The following must be completed before using the symptom tables.
  1. Perform Diagnostic System Check - Power Sunroof in order to verify that all of the following are true:
  2. ?€¢
    No DTCs are set.


    ?€¢
    The control modules can communicate via the serial data link.

  3. Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation
your better off taking to the dealer !

May 09, 2015 | 2001 Cadillac DeVille

1 Answer

We have a 2000 Ford Windstar that was in getting the transmission fixed. Since working on the transmission, the car won't start. We gave them both keys and they said they needed to get new keys from...


I am assuming that the vehicle ran prior to getting the transmission repaired. If so you should not need any new keys and the computer should be good. The shop doing the work has obviously done something wrong. If it did not run prior to taking it in for the tranny then it could be many things. Hard to tell without seeing the vehicle. If it was running prior to the work and it's still in their hands I would suggest you get it away from them ASAP.

May 11, 2011 | 2000 Ford Windstar

1 Answer

Want to program 4 new chip keys in1998 ford explorer


In order to program them yourself you will need 2 existing keys that are already programed to the vehicle. Step 1: Put the first key that starts it in the ignition and turn it to the run position then back to off and remove it. Step 2: Within 10 seconds repeat Step 1 with the second key that is programmed. Step 3: Within 10 seconds repeat Step 1 with the first new key and so on until you are on the last new key. Step 4: For the final key you will put it into the ignition and start the vehicle. The vehicle should start and all the keys should be programmed. Test out each key to make sure it starts the vehicle. If you don't have 2 existing keys you will have to take it to a Ford dealer and have them programmed. Also I'm not sure what the max amount of keys that can be programmed to a 98 Explorer is but I think its between 4 and 8.

Apr 07, 2011 | 1998 Ford Explorer

1 Answer

Don,t want to run or idle when cold


They put two different motors in the Explorer 4.0 overhead valve with vehicle Id code of( X) and the 4.0 single overhead Cam and a vehicle code of (E) If your vehicle has a E in the vehicle Id number I would replace the upper intake manifold gaskets. This particular Motor is very prone for the the upper Intake manifold gasket drying out and causing a large vacuum leak. The symptoms are engine will not Idle on dies on cold start up and after the engines reaches operating Temp idles fine .replace the upper intakes gaskets and I am sure you"ll be in great shape. Thanks for using fixya

Jan 07, 2011 | 1998 Ford Explorer

2 Answers

I have a ford explorer 1994 i lost the control remote, Installed a new alarm, but technician can not uninstall the factory alarm How can I do this? when new alarm is on, and opened the doors whit new...


Why not just get the factory PATS System working correctly. You can't remove the factory system,it's an integral part of you vehicles systems and processors

You can get new remotes and program them!!

May 26, 2010 | 1994 Ford Explorer Limited

1 Answer

1997 Ford Expedition - cruise control won't work. Need a diagram for the fuse block!Help!


Vehicles involved in the recall include the following:

1998-2002 Ford Ranger
1992-1997 Lincoln Town Car
1992-1997 Ford Expedition
1992-1997 Mercury Grand Marquis
1993-1998 Lincoln Mark VIII
1993-1995 Taurus SHO
1999-2001 Ford Explorer
1999-2001 Mercury Mountaineer
2001-2002 Ford Explorer Sport
2001-2002 Ford Explorer Sport Trac
1992-1993 E150-350 Vans
1997-2002 E150-350 vans
1993 Ford F-Series pickups
1993 Ford Bronco
1994 Mercury Capri
2003-2004 Ford F0150 Lightning
1995-2002 Ford F53 motor homes.

Apr 12, 2009 | 1997 Ford Expedition

1 Answer

1994 ford explorer


Did you have the key programmed to the vehicle? If not you will need to have another key (2 keys) and have them programmed by a ford dealer. Good Luck

Jan 04, 2009 | 1994 Ford Explorer Limited

Not finding what you are looking for?
2007 Ford Expedition EL XLT Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...