Question about 1997 Jeep Tj

1 Answer

High idle speed

4cyl with performance header and throttle body spacer.... High idle speed 1700 + or - a couple hundred. Won't settle down.
How do I get it to cooperate and what should the idle speed be for a 4cyl?
Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

700 rpm or so. Have you checked for vac leaks?

Posted on Sep 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why won't it idle above 1000 rpm?


no supposed to idle higher than that , usually even less .

Sep 24, 2015 | 2006 Ford Five Hundred

2 Answers

Code p0507


possible causes are:

Dirty throttle body
Electric throttle control actuator incorrectly adjusted/faulty/damaged
Air leak on Intake
Poor electrical connection to the Intake Air Control valve

P0507 KIA Idle Air Control IAC System RPM Higher Than Expected

May 14, 2014 | 2003 Kia Sedona

1 Answer

Every time i start my car it sounds like the revs are high then settles to normal revs what is causing this


If the idle speed is above 2000 RPM then drops down to normal, the common cause is a faulty idle air control valve or a dirty throttle body.

Jul 04, 2013 | Cars & Trucks

1 Answer

Hi i have a code reading P0506 for a 06 GMC Envoy XL any recomondations


{: ) DTC P0506 Idle Speed Low
The usual cause is an excessive carbon build-up on the throttle body. If this is the case, I suggest you have your throttle body cleaned and perform an idle relearn procedure using a GM scan tool. The idle relearn or reset procedure is very important, otherwise this code may still remain even after a throttle body clean.
In a similar fashion, if the ECM/PCM (engine control module) of a high mileage vehicle is replaced and/or reprogrammed without performing the Throttle/Idle Learn procedure, the ECM/PCM may no longer compensate for existing carbon build up in the throttle body, causing it to return with a similar concern as well as DTCs P0121, P0506, and/or P0507.
There are other conditions that can also affect or reduce idle speed by increasing engine load like incorrect torque converter clutch (TCC) operation, accessories that require additional torque to operate, restricted exhaust, and mechanical conditions that limit engine speed.

Aug 02, 2011 | 2006 GMC Envoy

1 Answer

Idling problem toyota altis


Either there is a vacuum leak causing the high idle, or
the IACV is bad or being controlled by the computer to make idle speed too high:

To change the IACV refer to the following:
Idle Speed Control (Idle Air Control) Valve Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the throttle body. Idle speed control valve toy_cor-04-18-1187.gif

  3. Remove the 3 mounting screws from the throttle body. Remove the idle speed control valve and gasket.
To Install:
  1. Using a new gasket install the idle speed control valve on the throttle body with the 3 mounting screws.
    • Tighten 33 inch lbs. (3.7 Nm).
  2. Install the throttle body.
prev.gif next.gif

Jul 16, 2010 | 2004 Toyota Corolla

2 Answers

I want to move my car speed up . it stop at 110 but i want it to go 120 ford five hundred


Dont you know THE TOP SPEED is 110 so stick with it as speed kills and it could be someone you NO

Sep 24, 2009 | 2006 Ford Five Hundred

2 Answers

1997 chevy want alot of horsepower and speed


Just a note, if this is an unaltered system, it should contain a sequential fuel injection system, which does not use a conventional throttle body. It uses a spider system instead, which is much different than the pre 1996 models.

Jun 07, 2009 | 1997 Chevrolet K1500

3 Answers

Engine revving itself.


some times when you put performance parts you have to adjust the gas flow to the engine and check you IDLE CONTROL VALVE that would cause reving on your car and your friends car also

Apr 26, 2009 | 1996 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...