Question about 2001 Chevrolet Silverado 1500

2 Answers

Knock sensor bank 2 sensor were is located? I can't find it, please help me locate the knock sensor ?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

V6 or V8? On 4.8, 5.3 and 6.0 it is under the intake. You have to remove the intake manifold.

Posted on Sep 07, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Expert
  • 205 Answers

Knock sensor Bank 1 & 2 !!!!!!!!!
These little doodads are supposed to adjust the timing when the engine "knocks" apparently. They are essentially microphones - your onboard ECM (computer) uses them to adjust the fuel/timing to avoid piston "knock" .The bad news - the (sensor) dealer cost is too expensive depending upon the wickedness of your local dealer. The labor? Probably a million or so.
They are mostly mounted either in the Air intake, throttle body or as in toyota UNDER the FUEL INTAKE.

Posted on Sep 07, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knock sensor for 2007 Saturn outlook. I can't pass emissions test!


Check engine light on ? What code ? There are many different (DTC'S) - diagnostic trouble codes that can set for knock sensors ! There all don't mean that you replace the sensor .
DTC P0324: Knock Sensor (KS) Module Performance
DTC P0325: Knock Sensor (KS) Circuit Bank 1
DTC P0326: Knock Sensor (KS) Performance
DTC P0327: Knock Sensor (KS) Circuit Low Bank 1
DTC P0328: Knock Sensor (KS) Circuit High Bank 1
DTC P0330: Knock Sensor (KS) Circuit Bank 2
DTC P0332: Knock Sensor (KS) Circuit Low Bank 2
DTC P0333: Knock Sensor (KS) Circuit High Bank 2

The knock sensor (KS) system enables the control module to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The sensors are located below each cylinder head on the engine block. The KS produces an AC voltage signal that varies depending on the vibration level during engine operation. The control module adjusts the spark timing based on the amplitude and the frequency of the KS signal. The control module receives the KS signal through 2 isolated signal circuits. The control module learns a minimum KS noise level at idle and uses calibrated values for the rest of the RPM range. The control module should monitor a normal KS signal within the noise channel.
Knock Sensor Replacement - Bank 1
Remove the exhaust manifold lower heat shield. Refer to Exhaust Manifold Lower Heat Shield Replacement.
Disconnect the engine wiring harness electrical connector (1) from the bank 1 knock sensor (2).
Loosen the knock sensor bolt and remove the knock sensor.
Knock Sensor Replacement - Bank 2
Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
Remove the engine oil filter. Refer to Engine Oil and Oil Filter Replacement .
Lower the vehicle.
Disconnect the engine wiring harness electrical connector (2) from the bank 2 knock sensor (3).
Loosen the knock sensor bolt and remove the knock sensor.

Nov 12, 2016 | Saturn Cars & Trucks

1 Answer

Where is the knock sensor located


This vehical has two knock sensors bank 1 and bank 2 ! bank 2 sensor screws into the side of the engine block closest to the firewall. and it is above the crank sensor. Knock Sensor (KS) Bank 1 sensor is on front side of engine block right of the oil filter and on the other side of knock sensor is the oil pressure sending unit.

Dec 26, 2014 | 2005 Saturn Relay

1 Answer

I am workimg on my 2000 nissan quest. it cranks and turns over but will not start. it is throwing codes P0340 twice and P0325. we replaced the distributor cap and rotor and still nothing. probably goi


P0325 Knock Sensor 1 Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
P0326 Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)
P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
P0329 Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)
P0330 Knock Sensor 2 Circuit (Bank 2) -Circuit Malfunction
P0331 Knock Sensor 2 Circuit Range/Performance (Bank 2)
P0332 Knock Sensor 2 Circuit Low Input (Bank 2)
P0333 Knock Sensor 2 Circuit High Input (Bank 2)
P0334 Knock Sensor 2 Circuit Input Intermittent (Bank 2)
P0335 Crankshaft Position Sensor -Circuit Malfunction
P0336 Crankshaft Position Sensor -Range/Performance
P0337 Crankshaft Position Sensor -Low Input
P0338 Crankshaft Position Sensor -High Input
P0339 Crankshaft Position Sensor -Intermittent
P0340 Camshaft Position Sensor A Circuit (Bank 1 or Single Sensor) -Circuit Malfunction
sorry would a play with this to know for sure ,check the wiring plugs onto the sensors to make sure their not full of oil or corroded

Aug 07, 2014 | 2000 Nissan Quest

1 Answer

Circuit bank 2


Knock sensors are on the side of the engine block under the intake manifold. Bank 2 would be the sensor closest to the transmission above the starter as I recall.

May 24, 2014 | 1998 Volvo S70

1 Answer

Where is my knock sensor bank 2 located at on my jaguar x-type? (2002, 2.5 cylinder v6)


There are two knock sensors located on top of the Engine, approximately in the middle of the 4 cylinders at each bank.
To get access to the sensors the black plastic engine cover with the "Jaguar V8" imprinted on has to be removed.

There are two types of knock sensors.
The "old" ones that are of a "screw-in barrel type" and the newer ones that are just bolted on.

I describe the replacement of the bolt-on type knock sensor on Bank 2 in the following documentation on a 1999 XJ8 AJ27 engine.

Be careful!
Knock sensors are piezo electric devices that are very sensitive! If dropped, over-torqued or struck they will probably be destroyed.
As knock sensors are sensitive to a sudden temperature change they are also easily fractured by steam blasting a hot engine.
So handle the knock sensors with great care and let the engine always cool before fitting a new sensor!

Feb 20, 2012 | 2002 Jaguar X-Type

1 Answer

Where is knock msensor bank 2 on 04 2500 series 6.0 located


They are Located UNDER Intake Manifold !! #1 bank in Front #2 Back.

  1. Remove the intake manifold.
  2. Gently pry up the rubber covers.
  3. Disconnect the knock sensor electrical connectors.
    1. Remove the knock sensors.
    INSTALLATION PROCEDURE

    NOTE: Refer to Fastener Notice in Service PrecautionsInstall the knock sensors. Tighten Tighten the sensor to 20 N.m (15 lb ft)
    1. Connect the knock sensor electrical connectors.
    2. Push down on the rubber covers.
    3. Install the intake manifold.

Oct 08, 2009 | 2003 GMC Sierra

4 Answers

Knock Sensor


Knock Sensors are located below the intake manifold or intake plenum and mounted to the block. They are circular and have a bolt at the center. On V6s,8s etc. and flat styled motors, they will have two knock sensors (bank 1 and 2). Bank 1 or 2 relate to V6s/8s/10s etc., or flat styled motors which have two separate heads and exhaust manifolds. Each manifold is a bank, so if there are two manifolds there are two banks. Hopefully this helps

Sep 07, 2009 | 2002 Chevrolet Silverado 2500HD

1 Answer

I own a 2003 Chevrolet Express 3500 cargo van. The check engine light came on and the local hardware store, break out box indicates that the knock sensor circuit is the problem, bank 2. Which side of the...


OK, bank2 is the side where the #2 piston is on. Usually its the pasanger side. To be sure open the hood and see which cylinder head is more forward than the other. the cylinder head set back is the bank 2 side. The knock sensor is located on the bank side of the block. You dont need a special tool. only a wrench. Make sure you clear all codes after installation of sensor.

Jul 23, 2009 | Chevrolet Express Cars & Trucks

1 Answer

Knock sensor location


if its a cmfi or csefi injection system theres 2 knock sensors 1 on each side of engine block,1 under the left bank of block,the other under right bank of block,tbi inj. theres 1 in front of starter.

May 27, 2009 | 1994 Chevrolet C1500

Not finding what you are looking for?
Cars & Trucks Logo

899 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...