Question about 2002 Lexus IS 300

1 Answer

The window is bending in when it goes up - 2002 Lexus IS 300

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

It sounds like the window has jumped the track and is riding up the outside of the track. As the window moves up, it forces it to a flatter angle and "tips" it inward. No real solution other than removing the inner door panel and setting things straight. While it's open, check for broken pieces, missing screws, etc.

Posted on Sep 06, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The left power mirror is not working together with the window. Could it be fuses and which ones are they?

Check the door hinge area where the wiring harness goes from the door post to the door. After a while the wires can break from continuous bending. You may have to pull back a protective boot.

Jul 03, 2015 | Cars & Trucks

1 Answer

I have a 2003 dodge neon interface motor have you heard the pistons bending when the water pump goes out?

pistons are just blocks to fill up the hole. The rings do the sealing of the block or piston to maintain compression. When the water pump goes out then the engine overheats and the rings soften and break scoring the cylinder walls . In really bad cases the rings may seize and break the lands out of the pistons but pistons do not bend. Con ( connecting rods ) will bend if there is an excess of water allowed into the combustion chamber and when the piston comes up and there is not enough space left for the piston to go over TDC then the con rods will bend /break and if really bad will bend a crankshaft. It is an interference motor and if the cam belt breaks then the pistons will hit and bend the valve heads as the pistons hit the open valves

May 11, 2014 | Cars & Trucks

1 Answer

Driver side window goes down but not back up when you close the door

where the door bend there is a harness and some wires are cut

Dec 12, 2013 | 2006 Pontiac G6

1 Answer

My 1999 silhouette driver side power window generally goes down ok but when it goes up the window begins to lean forward and gets into a bind. Are there some guides that might be missing? I have already...

its not sat correctly in the guides, normally there will be a adjuster on the door genrally a 10mm bolt loosen it and correct the position, also check the inner window seal rubber that runs down inside the door sometimes the seals are offset when the regulater broke it bends the metal strip that hold the rubber in the correct position.

Jan 14, 2010 | 1999 Oldsmobile Silhouette

1 Answer

Locked keys in car

You have 3 options:

A: Use a coathanger to go over the top o the window, bending it down as you go, and bend the end so that you can catch the door handle enough to open it.

B: Buy or borrow a "slim jim" which parking lot attendants use when keys are locked in cars. It slides down the outside of the window and a hokk in the end catches a thin bar or rod that goes from the inside doorhandle to the lock. Takes some fiddling but not hard.

C: Call a locksmith for automobiles and watch him do the second item.

Oct 30, 2009 | 1997 Buick LeSabre

1 Answer

2000 range rover pasenger window does not set all the way

Ok any more there is not any adjustment for this problem what you have to do is roll the window down all the way and put your knee on the door (inside) right where the top of the window is and pull the top of the door tword you this will bend the door frame inward and also make your seal tighter.. Now dont over do it and bend the **** out of it just trial and error is what you have to do .. bend it just a little and see if you can put a dollar bill in the top of the door between the rubber and the door and pull it out .. to see if the seal is tighter .. try it before you start bending it too this way you can tell if you are helping .. thanks again Jerry ..

Feb 08, 2009 | 2000 Land Rover Range Rover

1 Answer

Need to know which fuse runs auto windows for 1996 jeep chereokee

the power windows work on a circuit breaker ...not a fuse. experience says to check the wiring that goes into the drivers door right where the harness bends ......more than likely a broken wire

Sep 26, 2008 | 1996 Jeep Grand Cherokee

1 Answer

Rear passenger window

You didn't say if the window doesn't work with both the switch at the drivers door and at the rear door. If it works at one and not at the other, then that switch is bad.
The windows all use the same fuse. Most likely the motor has froze up from corrosion, or the wire to it is broken. The wiring goes into the door by the hinges in a rubber convoluted hose, and it bends back and forth each time the door is opened and shut.

Jul 02, 2008 | 2003 Toyota Camry

Not finding what you are looking for?
2002 Lexus IS 300 Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts


Level 3 Expert

76691 Answers


Level 3 Expert

905 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides