Question about 2009 Mercedes-Benz C-Class

Open Question

How do I put a cold air intake in a smart car i have all the screws out of the stock one put i cant get it out their is not enough room!!

Posted by on

  • yadayada
    yadayada May 11, 2010

    SORRY ABOUT THAT BUT WHAT U ARE DOING ON THIS LITTLE ENGINE IS A HUGE WASTE OF TIME.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

After installing k&n cold air intake on my 2014 Sierra ,it bogs when you hit the gas. Does anyone know the problem?


The problem is you installed an expensive piece of junk in your car instead of just renewing your stock air filter element every year or 18 months to keep it clean and free flowing.

Take it up with K and N who told you what a great product it was for your vehicle and who will now tell you that your installation is faulty which in any case, it may well be.

But in any case just changing the intake air flow characteristics from stock can be enough to make your engine running poorly and no amount of fiddling with the replacement intake will remedy this kind of problem when it occurs.

Did you fall for the tiny HP gain shown in their videos. Well putting a vehicle on a Dyno with an old and dirty stock air filter is going to produce poor performance compared to a second Dyno test where a new air filter is installed regardless of whether it is a good factory stock item or a K and N product. By the way independent tests have shown clearly that the K and N air filters allow much more dirt to enter your intake than the efficient stock OEM air filters do. Yes, the filter is there to keep out the dirt particles.

Put the stock system back on with a new air filter element and your engine will run properly again.
.

Apr 03, 2016 | Cars & Trucks

1 Answer

I put a upgrade air intake why does it turn off when exselarate truck


To much air and not enough fuel, restore it to stock

Feb 23, 2012 | 1999 Ford Expedition

1 Answer

Put K&N cold air intake in audi its not cranking over now?


make sure everything that was plugged up to the stock air cleaner and box ansd make sure everything is plugged up properly

Feb 20, 2012 | Audi A4 Cars & Trucks

1 Answer

Installed an aftermarket air filter kit and now have a code of PO113


Have you tested your IAT (Intake Air Tempature sensor) ? Did you install in your new cold air intake? The P0113 code sets when it senses an air temp of -31 degrees F for more than 5 second . If you test your IAT with an ohm meter it should have continuity at room temp. the warmer it is the less resistance it should have. the colder it is the more resistance it should have. If you have no continuity the IAT is bad and needs replacing.

Jan 26, 2012 | 2011 Chevrolet Camaro

1 Answer

CEL came on for the car, says it is idleing too high/low. After I just put on a cold air intake. Cleared code and the CEL came back on the next day. Anyway I can turn the idle down manually?


There is no way for you to turn the idle down manually, it is all computer controlled. Do not adjust any screws on the throttle body, they are set from the factory. The only way you may be able to fix your idle problem with out getting rid of your cold air intake and replacing it with the factory is by removing both the positive and negative leads on the battery and holding them together for about 5 min while disconnected. This will reset the cars computer and may compensate for the intake. If this does not help you will need to remove the after market intake and put back in the stock one.

Feb 28, 2011 | 2006 Dodge Stratus

3 Answers

Idleing low on my chevy silverado 04


When swapping intakes you may left something unplugged or unhooked recheck the swap and connect any item left.

Jul 16, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

2 Answers

How to take out stock air intake for a saab 9000 turbo


depends if yours has the flat panal filter or the round type both can be changed for a k&n performance filter wear you never ever replace it again only clean and re-oil at every service
the round type is on the front lower side pass side 3 spring back clips hold the front cover on
the panal filter is squire and has 3 or 4 spring back clips just lift the lid and change

Jun 04, 2009 | 1991 Saab 9000

1 Answer

Dashboard removal... gets stuck on the steering wheel base


I can't help you with the srew, it takes what ever it takes to remove it, have you drop the steering column dowm by removing the column clamp on the bottom of it, you have to drop the column to get enough room.

Sep 26, 2008 | 1995 Chevrolet Blazer

Not finding what you are looking for?
2009 Mercedes-Benz C-Class Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...