Question about 2007 GMC Yukon Denali

Open Question

I need to remove the grill to replace headlight assemblies

I've removed the 2 upper screws and the one in the grill. The front cap assy seems to be retained at the bottom but I don't see fasteners. Can anyone help?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove headlight assembly on 2013 Dodge Journey


First, you need to disconnect the negative battery cable. Then loosen up the front fascia on the side where you are removing the headlight assembly. Remove the 4 push pins that fasten the upper grille to the FEM (Front End Module). You will then need to push the fascia and grille forward enough so that you can remove the three screws which hold the headlamp assy. to the FEM. Finally, you pull the assy. far enough away from the FEM to reach the headlampand dash wire connectors from the rear of the headlamp housing.

Jul 25, 2014 | 2009 Dodge Journey

1 Answer

How do i change the headlight on a clio 2005


1 Remove the front grill.


2 Remove the screws that secure the headlight assembly to the vehicle.


3 Unplug the wiring from the back of the headlight assembly. Then, gently pull the old headlight assembly from the vehicle and set it aside.


4 Replace the headlight assembly by inserting the new assembly into place and replacing the screws.


5 Insert the grill back into place and replace the screws to hold it in place.


From Chinasiony Electron

Aug 13, 2012 | 2005 Renault Clio 1.4

1 Answer

Installing a new headlight


pop hood..there is a star screw about 5 inches long on each side turn it counterclockwise to uninstall the headlight assembly. you may have to remove the grill piece 4 screws then remove turn signal assembly 1 screw on outside edge of van.once headlight assy removed turn headlight 1/4 turn to get to the head lamp bulb. install in reverse order

Jan 28, 2011 | 2005 Dodge Grand Caravan

1 Answer

Remove headlight assembly from a 2001 Dodge Ram


On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Apr 10, 2010 | 2004 Dodge Ram 1500

1 Answer

Headlights removal ford explorer 96


  1. Check that headlamp switch (11654) is in the off position.
  2. Lift hood (16612).
  3. Release latch and swing filler panel to left or right.
  4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
  5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
  6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal. 7056091.gif
Headlamp Assembly, Explorer
Removal and Installation
  1. Disconnect battery negative cable.
  2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
  3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
  4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
  5. Remove attaching screws (4) located across top of grille.
  6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
  7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
  8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
  9. Disconnect wiring from headlamp bulb socket.
  10. If replacing headlamp housing, remove retaining collar and bulb.
For installation, follow removal procedures in reverse order. Make sure to check headlamp aim. 568a220.gif

Apr 02, 2010 | 1996 Ford Explorer

3 Answers

Headlight


Well according to my mitchell manuel you don't have to.here is the procedure.
1. open the hood.
2.Remove the push-pin retainer's that secure the top of the upper facia and grill assembly to the upper tie bar to allow the upper facia and grill assembly to flex forward.
3. remove ther bolt and push-pin retainer that secures the top of the headlight assembly to the upper tie bar.
4. Gently pull the upper facia and grill assembly forward to access the bolt on the inboard side of the headlight assembly
5. Pull the headlamp assembly straight out to disengage the the snap in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the inboard assembly clears the front facia.
6. pull the assembly out and away from the veh.From there you'll be able to access bulbs.
be careful not to touch the bulb with fingers or oil in skin will blow bulb.
Good luck.

Aug 19, 2009 | 2004 Cadillac SRX

1 Answer

Replacing headlight assemblies in a 1994 chevrolet silverado


it is a very easy diy job. all you have to do is take the grill off by removing the signal lights and taking 5 to 6 screws out of the grill. pull the grill out of the way making sure to unhook the marker light wires. then on your headlight assemblies, unscrew the four 10millimeter screws on each then pull the assy. away and unhook your wires. install is the reverse of removal, its really easy. good luck

Jul 05, 2009 | 1994 Chevrolet C1500

1 Answer

How to take out the light assy on a 2004 Toytota sienna van.RH side. Do you have to take off the front cap (bumper)


Yes....herer is the steps to replacing it:

Headlight Assembly Removal & Installation Standard Headlights To Remove:
  1. Disconnect the battery ground cable.
  2. Remove the left and right front inner fenders. Fog light & headlight assembly (exploded view) toyota-06-00-5662.gif

  3. Remove the 8 screws and separate the front splash shield from the front bumper fascia.
  4. Remove the 5 push-pins from the top of the fascia grille.
  5. Release the retainers on the left and right sides of the front bumper fascia and pull the fascia toward the front of the vehicle.
  6. Disconnect the headlight assembly connectors.
  7. Remove the mounting bolt, 3 screws and headlight assembly.
  8. Turn all bulb sockets counterclockwise to remove.
To Install:
  1. Turn all bulb sockets clockwise to install.
  2. Align the retainers with the slots and install the front fascia.
  3. Install the 5 push-pins on top of the fascia grille.
  4. Install the front splash shield on the front bumper fascia with the 8 screws.
  5. Install the left and right front inner fenders.
  6. Connect the battery ground cable.
  7. Vehicles with power windows perform the following steps:
    • Turn the ignition switch on.
    • Open the power window halfway.
    • Close the window and continue to hold the switch up for at least 1 second after the window is closed.
    • Ensure that the auto up/down circuit is operating properly.
    • If the auto up/down circuit does not operate, disconnect the battery ground cable for 10 seconds.
    • Connect the battery ground cable.
    • Turn the ignition switch on.
    • Open the power window halfway.
    • Ensure that the auto up/down circuit is operating properly.
    • If the auto up/down circuit does not operate, turn the ignition switch on.
    • Open the power window halfway.
    • Close the window and continue to hold the switch up for at least 12 second after the window is closed.
  8. Vehicles with sliding roof system perform the following steps:
    • Turn the ignition switch on.
    • Press and hold the TILT UP switch until the glass tilts to the full up position. The glass will automatically tilt slightly down after it reaches the up position.
    • Release the switch.
    • If the sliding roof does not operate properly, replace the sliding roof ECU.

May 07, 2009 | 2004 Toyota Sienna

2 Answers

How to remove grill on 1998 Tahoe. Have to replace headlight assy.


THE TOP SCREWS ARE EASY. THEN THERES THE BOTTOM OF THE GRILL. REMOVE PARKING LIGHTS. THERE ARE 3 PLACES AT THE BOTTOM OF THE GRILL THAT HOLD IT. THERE ARE NO SCREWS OR BOLTS TO REMOVE. JUST 3 PLACES WITH PUSH BRACKETS. LEFT, RIGHT AND CENTER,,A LITTLE TRICKY BUT DONT GIVE UP. LIFT AND PULL THESE TABS/BRACKETS. THE BOTTOM CHROME SHOULD COME OUT A TAB AT A TIME. YOU WILL DO GOOD,,,,RIGHT? YES

Apr 27, 2009 | 2003 Chevrolet Tahoe

1 Answer

How to replace 1998 Ford Contour headlights (with diagram)


Step 1
Remove your Contour's front grille. You can do this by raising the hood and removing two screws that are located on top of the grille.

Step 2 Remove the headlight assembly. The headlight assembly is held into the front of your Contour by three screws. Two screws will be located on top of the assembly, and one on the bottom.

Step 3 Replace the headlight assembly, if necessary. If you are only changing individual bulbs, make sure you replace the correct bulbs. Each assembly holds three light bulbs, including the bright, dim and turn signal bulbs.

Step4 Replace the headlight assembly and reattach the three screws to hold it in place.

Step5 Replace the front grille of your Contour and the two screws that hold it onto the front of the car.


  • It is usually a good idea to replace bulbs together (in pairs). This will allow the bulbs to wear at the same rate.
  • If you choose to replace only the individual light bulbs, do not touch the new light bulbs. The contact of your skin on the bulbs will cause the light bulbs to burn out much sooner.

Let me know if you have any further questions.


Benjamin

Apr 26, 2009 | 1998 Ford Contour

Not finding what you are looking for?
2007 GMC Yukon Denali Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...