Question about 2008 Dodge Avenger

Open Question

Cant find the spark plugs locations for a 2008 dodge avenger 2.4 liter

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2008 dodge avenger spark plug location and socket size.

  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Posted on Feb 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change the rear 3 plugso on a 2008 dodge avenger


2.5 liter?

The plenum will need to be removed in order the replace the rear spark plugs.

Apr 04, 2015 | 2008 Dodge Avenger

1 Answer

Spark plug gap 2008 avenger 6 cylinder


check your owners manual it there as well look under the hood its on a decal on the rad support or the underside of the hood

Aug 09, 2014 | 2008 Dodge Avenger

1 Answer

Where is the alternator fuse on a 2008 dodge avenger?


look in the fuse block, driver's side, forward corner of engine bay under the hood. I think the lid on the little box has the diagram underneath it, to locate the alternator fuse. Check all your fuses there, too.
I think the small plug-in connector with two wires on the alternator would be for the voltage regulator, wouldn't it?

Feb 14, 2012 | 2008 Dodge Avenger

1 Answer

What is the spark plug gap for a 2008 dodge avenger with a 4 cylinder?


There should be a data plate on the radiator support or a decal on the under side of the hood that has the reccomened plug gap.

May 27, 2011 | 2008 Dodge Avenger

1 Answer

Where are the spark plugs located in a 2008 dodge avenger?


They screw into the engine block. Open the hood and look for wires going to the block. Pull one wire away from the engine block. Below, is the spark plug.

Oct 11, 2009 | 2008 Dodge Avenger

1 Answer

Where is the oil drain plug in my 2008 Dodge


it will be at the lowest point of the oil pan

Sep 27, 2009 | 2008 Dodge Avenger

1 Answer

Im looking for the spark plugs in my 2008 doge avenger and i cant find them i will like to change them my self


The Spark plugs in your Avenger is good for 100,000 miles and you should not need to replace them unless there is a problem, which would be indicated by the Mill light on the dash. If you must, you can pick up the spark plugs at Auto Zone and they can give you the step by step instructions to replacing the spark plugs with common tools. Good luck. Note: It's common for the doge tech to reset the engine when doing a tune up to prevent any misfire that occur when new plugs are installed. 

Jul 16, 2009 | 2008 Dodge Avenger

4 Answers

2008 dodge avenger spark plug location and socket size.


  • 2008+ Dodge Avenger 2.4L 4cyl.
  • Remove plastic cover on top of engine, just pull on each corner for it is friction fit.
  • Once removed you will see 4 black spark plug covers with one hex type screw holding each.
  • Remove Hex screw and place aside, pull upward to remove plug boot from plug.
  • To remove the plug, use a 5/8 socket with a 6" extension. Once plug has been turned out all the way and you cannot get the plug up and out of the hole, just press the plug boot back on the plug and pull it back up.
  • Gap and replace 4 plugs with the same or equavalent type,. Drop plug down the hole and use socket to align and tighten until just snug, then torque to manufactures specifications.

Feb 14, 2009 | 2008 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...