- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
SERVICE STEERING SYS
Refer to Variable Effort Steering System Description and Operation in Variable Effort Steering
Your best bet , take it to the dealer .
Variable Effort Steering System Description and Operation
The Variable Effort Steering (VES) System varies the amount of effort to steer the vehicle as wheel speed changes or lateral acceleration occurs. The Electronic Brake Control Module (EBCM) controls an actuator located in the steering rack and pinion. The actuator consists of an electromagnetic coil and a pintle valve which moves in and out of the rack and pinion's input fluid orifice, regulating power steering fluid flow. The EBCM commands current from 0-1 amp to the VES actuator which varies the amount of effort to steer the vehicle. At low speeds, 1 amp of current is commanded to the VES actuator and the pintle valve is fully retracted which provides maximum fluid flow and maximum steering assist for easy turning and parking maneuvers. At high speeds, no current is commanded and the pintle valve moves closer to the orifice, decreasing fluid flow, providing firmer steering (road feel) and directional stability. The VES system uses the steering wheel position sensor input to calculate lateral acceleration during abrupt driving maneuvers. The system also uses the Antilock Brake System (ABS) wheel speed sensor inputs to determine vehicle speed. The EBCM is constantly monitoring these inputs to achieve the desired current to the VES actuator. The EBCM has the ability to detect malfunctions in the VES actuator or the circuits to the actuator. Any malfunctions detected will cause the VES outputs to be disabled and the EBCM will command the Driver Information Center (DIC) to display the SERVICE STEERING SYSTEM warning message via a class 2 serial data circuit.
Step
Action
Yes
No
Schematic Reference: Steering Assist Schematics
1
Install a scan tool.
Does the scan tool turn ON?
Go to Step 2
Go to Scan Tool Does Not Power Up in Data Link Communications
2
Turn ON the ignition, with the engine OFF.
Attempt to establish communication with the EBCM.
Does the scan tool communicate with the EBCM?
Go to Step 3
Go to Scan Tool Does Not Communicate with Class 2 Device in Data Link Communications
3
Select the ABS Diagnostic Trouble Codes function on the scan tool.
Does the scan tool display any DRP/ABS/TCS or VSES DTCs?
Go to Diagnostic System Check - ABS in Antilock Brake System
Go to Step 4
4
Does the scan tool display any DTCs which begin with a "U"?
Go to Diagnostic Trouble Code (DTC) List in Data Link Communications
Go to Step 5
5
Does the scan tool display "DTC C0450?"
Go to Diagnostic Trouble Code (DTC) List
System OK
Some fixya user told me a website reliable-store it is very good.. I used it to repair my shredder it had some spark issue which wasn't easily fixed. you can go the re and try
Do you know if your vehicle has --------------------------------------------------------------------------------
Power Steering System (w/o Electro-Hydraulic Steering) or
Variable Effort Steering System
The variable effort steering (VES) system or MAGNASTEER® varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking maneuvers. Steering effort is increased at higher speeds to provide firmer steering for increased road feel and directional stability. The electronic brake control module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and set a DTC.
Are there any other lights lit on the dash ? ABS ?
DTC C0450 Steering Assist Control Solenoid/Motor/Actuator Circuit could have a diagnostic trouble code !
The electronic brake control module (EBCM) commands current from 0-1 amp to the variable effort steering (VES) actuator, depending on vehicle speed. At low speeds, 1 amp of current is commanded to the actuator and the actuator valve is fully closed. A speed increases, less current is commanded to the actuator and the valve opens, allowing pressure to bleed off through a power steering fluid orifice. The EBCM monitors and compares the Commanded and Feedback Current parameters to detect malfunctions in the VES system.
Or you could have a bad steering rack !
Charging System/Generator Fault
Refer to Charging System Description and Operation in Engine Electrical
Alternator problem maybe !
The electrical power management (EPM) system is designed to monitor and control the charging system and send diagnostic messages to alert the driver of possible problems with the battery and generator. This EPM system primarily utilizes existing on-board computer capability to maximize the effectiveness of the generator, to manage the load, improve battery state-of-charge (SOC) and life, and minimize the system's impact on fuel economy. The EPM system performs 3 basic functions:
• It monitors the battery voltage and estimates the battery condition.
• It takes corrective actions by adjusting the regulated voltage.
• It performs diagnostics and driver notification.
The power steering pump has nothing to do with it .
Variable Effort Steering System Description and Operation
The Variable Effort Steering (VES) system or MAGNASTEER?® Varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking Maneuvers. Steering effort is increased at higher speeds to provide firmer steering (road feel) and directional stability. The Electronic Brake Control Module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and setting a DTC.
Your best bet is take your vehicle to a GM dealer or a ASE certified repair shop that knows about this system .
This is a very complex system an if you don't work on these systems all the time , I suggest you take it to a ASE certified repair shop that does !
The Variable Effort Steering (VES) system or MAGNASTEER?® Varies the amount of effort required to steer the vehicle as vehicle speed changes. At low speeds, the system provides minimal steering effort for easy turning and parking Maneuvers. Steering effort is increased at higher speeds to provide firmer steering (road feel) and directional stability. The Electronic Brake Control Module (EBCM) controls a bi-directional magnetic rotary actuator located in the steering rack and pinion. The EBCM varies the steering assist by adjusting the current flow through the actuator to achieve a given level of effort to steer the vehicle. The VES system accomplishes this by adding or subtracting torque on the input shaft to the rack and pinion. The main component of the system is an electromagnetic actuator, which consists of a multiple-pole ring-style permanent magnet, a pole piece, and an electromagnetic coil assembly. The VES system uses the ABS wheel speed sensor inputs to determine vehicle speed. When the EBCM senses wheel speed, it commands a current to the VES actuator that is most appropriate for each speed. The EBCM commands current from negative two amps to positive three amps to the actuator, which is polarized. At low speeds, a negative current is commanded, which assists steering. At medium speeds no current is commanded and steering is assisted by hydraulics only. At high speeds, a positive current is commanded, which creates steering resistance. Ignition voltage and ground are provided through the EBCM. The EBCM has the ability to detect malfunctions in the actuator or the circuits to the actuator. Any malfunctions detected will cause the system to ramp to zero amps and steering will be assisted by hydraulics only and setting a DTC - diagnostic trouble code !
my radio keeps reading amp error when I plug it in
×