Question about 1992 Honda Accord

1 Answer

Rear brakes How do I put the new rear brakes back on? I'm having a problem with the hyd. unit compressing?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

You may have to turn it ......screw it back in as it goes in.

Posted on Sep 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake shoes from old rear axle not fitting on to the new rear axle 2002 durango


you have compress the caliper piston to get brake shoes back on.

Feb 05, 2013 | 2002 Dodge Durango

1 Answer

Rear rotor replacement for a 1985 mercadies benz 500 sel


YOU NEED TO SAFELY RAISE SUPPORT REAR OF VECHICLE ON JACKSTANDS. MAKE SURE VECHICLE PARKED ON SOLID LEVEL GROUND. YOU NEED TO SIPHON JUST A LITTLE BRAKE FLUID OUT OF THE MASTERCYLINDER.BECAUSE YOU NEED TO USE LARGE C - CLAMP TO COMPRESS FORCE PISTONS BACK IN THE CALIPER BORES USING LARGE C - CLAMP DOING THIS WILL ALLOW YOU ENOUGH ROOM INSTALL NEW REAR BRAKE PADS.TO REMOVE REAR PADS ONCE YOU COMPRESS PISTON BACK IN THE CYLINDER BORE. YOU CAN TO REMOVE REAR BRAKE PADS BY REMOVING RETAINING PINS IF EQUIPPED OR BRAKE PADS HELD IN PLACE BY RETAINING BOLTS.ONCE YOU HAVE NEW REAR BRAKE PADS INSTALLED.PLACE MASTERCYLINDER COVER BACK ON TOP OF MASTERCYLINDER THEN PUMP BRAKE PEDAL TO SEAT NEW REAR BRAKE PADS AGAINST THE ROTOR UNTIL BRAKE PEDAL FEEL FIRM AND SOLID.THEN RECHECK BRAKE FLUID LEVEL IN BRAKE MASTERCYLINDER ADD LITTLE MORE FLUID IF NEED DONT OVER FILL MASTERCYLINDER.

Sep 11, 2011 | Mercedes-Benz 500-Class Cars & Trucks

1 Answer

How do i remove the rear brake to replace the pads on my 2002 gmc 2500 4x4?


pull the caliper mounting bolts,hang it from a clothes hanger,compress the piston to make room for the new pads,put every thing back like it was, check brake fluid. (open bleader on caliper when compressing piston.)

Dec 22, 2010 | 2002 GMC Sierra 2500HD

1 Answer

Rear brake pads replace


Rent a tool from auto zone to help you compress the rear brake piston. It cannot be compressed with c clamp because the piston must be turned while it is compressed.
Autozone will charge you approx. $60 for the rental and then you get all your money back when you bring the tool back.
You need to compress the rear piston so you have room for the new, thicker pads.
The rest of the job is just like any other brake job. 1. remove one pin bolt and rotate caliper open to get to the pads. 2. compress the piston in with the tool 3. replace the pads. 4. assemble.

Oct 27, 2010 | 2008 Dodge Grand Caravan

3 Answers

Compressing the rear disc brake caliper on 2008 grand caravan


The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Mar 07, 2010 | Dodge Caravan Cars & Trucks

1 Answer

Replacing my rear brake pads. Cannot make the caliber open bigger to fit the new pads in.


hi had this problem myself i had to relese the hyd pressure and then bleed the brakes after

Nov 18, 2009 | 2000 Lincoln LS

1 Answer

How to replace rear brake pads


Jack up car, remove wheel. There are two bolts that hold the caliper on. Remove these. Caliper comes off, take old pads out. There is a special tool to compress the piston back into the caliper (do not use a C Clamp on the rears.) Put new pads back on, re-install the caliper, and put the wheel back on. Pump the brake pedal until it is firm. Done.

May 27, 2009 | 2006 Ford Focus

3 Answers

Cant compress piston on rear brake calipers


Use a caliper wind back tool which rotates the piston at the same time as pushing it back. Release the bleed screw to assist the wind back. If you use a brake hose clamp on the brake hose this will reduce the need to bleed the system.

Mar 23, 2009 | 2003 Volkswagen Passat

3 Answers

2005 malibu rear disk brakes


I didn't have a "cube tool", used a pair of channel locks. Worked great. Thanks.

Jun 19, 2008 | 2005 Chevrolet Malibu

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...