Question about 1991 Mazda 626

2 Answers

Mazda 626 1991 back brake ligths not working

Mazda 626 1991
left handdrive

have tested bulbs and working ok
have tested for power to the bulbs and get no reading
all other back lights work
fog light
side lights
reverse lights

cannot understand why no power to back stop lights?

Posted by on

  • noelarcher Sep 06, 2009

    sorry have checked fuse 15amp and tested fine,
    how do i check the brake pedal for power coming from it with the brake depressed?

  • noelarcher Sep 06, 2009

    where is the brake light switch?

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

Is the fuse for the brake lights OK?
Check for power to the brake light switch at the brake pedal and for power coming from it with brake pedal depressed.

Posted on Sep 06, 2009

Testimonial: "just a bit more information from me to help me more :)"

  • 498n Sep 07, 2009

    The brake light switch will be mounted above the brake pedal pad up behind the dash.It is turned off and on by the brake pedal.
    Look for wires going to a switch in this area.Some of the wires should have power in them with the brake pedal untouched and others should have power with the pedal depressed.


×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 69 Answers

I am probably too late for this one, I had previously posted a fix for this problem. But here we go again. If you have checked the fuses, brake switch and you are still having the problem, the you will need to replace what is called the multy function switch it is the same one that you turn your healights on and offm high beam and turn signal. Good luck

Posted on Feb 26, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 mazda 626,front left turn signal doesn't work (blinks rapidly on dash)Only when the headlights are on, 4 way emergency flashers work fine. Bulbs ok. changed flasher it's ok. ???


I hear what you are saying however....whenever there is a bulb that is not good....you will get rapid flashing on the dash. Replacing the bulb is cheap...do it as a test if nothing else.

Semper Fi,
Z

Apr 29, 2017 | Mazda Cars & Trucks

4 Answers

Brake lights not working on my 1985 ford f150 after I replaced the brake switch


disconnect turn signal switch wires @ column, put power to wires to brake lights. that cks wiring to lights. next put power to wires through turn signal to ck switch. Power runs from brake light switch to turnsignal switch, to lights.

Oct 18, 2014 | 1985 Ford F150

1 Answer

On 92 Mazda mx3 running lights in don't work but


check if power getting to bulbs, if is then the bulb holders may well be distorted due to heat and are not allowing bulbs to seat properly so renew the bulb holders , if no power to the bulb holders and the fuse is ok then its either a wiring fault , check the earth wire from the light cluster if ok them must be the switch

Oct 15, 2014 | 1992 Mazda MX-3

2 Answers

My left brake light/turn signal isn't working! I replaced the bulbs and turn signal flasher! Still not working! Its 2000 Chevy s10 blazer


If the other brake and turn lights are working the brake light and flasher units are ok . With a test light check at the bulb holder terminal and bulb holder body, test light should glow ,if not check from terminal to a metal part of panel away from the light body . If test light now glows the brake light body has a bad earth if the test still not glowing the power cable to the light is broken.

May 20, 2014 | Cars & Trucks

1 Answer

Im replacing a tail light circuit board on both rear lights, is their any special way to do this


just check accurately bulbs if you mixed it could happen like that, some cars for the brake lights use two contact bulbs some of them single contact, two contact bulbs can give two signals which one is used for brake ligths and another for taillight, so check the bulbs carefully

Apr 13, 2014 | Dodge Stratus Cars & Trucks

1 Answer

97 cad turn signal lift side and brake not working **** right is working


The problem could be in one fuse, bad ligth bulb, bad combination switch wich is the turn signal lever siwtch, or the combination of all this. Is the front left turn signal working, in order to find out if the turn signal switch is working check for power at the the cable in the corredpondent connector that way you eliminate the posibilty of the turn signal sitch if you have power at the connector also do the same at the stop ligth if there is no power you have problaby bad fuse, hope this help tou out.

May 13, 2012 | Cars & Trucks

1 Answer

2000 MAZDA 626 BRAKE LIGHT NOT ON


First check for blown fuse. If Ok check bulb, If ok use test light (computer safe led type)
Get someone to put on brake and earth test light lead to bold on vehicle and hold test light probe in centre of bulb holder. It should light up.
If not move earth lead to another bolt on vehcile and retest.
If light comes on in test light the bulb is broken.
If no light in test light the brake light switch connected to the brake pedal is broken. replace brake light switch.

Jun 12, 2011 | Mazda 626 Cars & Trucks

1 Answer

My reae left tail ligth won'r turn on? the rigth


Check the fuse in the fusebox inside for a blown fuse,the brake lights are working so check the plug going onto the back of the lamp for tightness,could be a loose connection.

Jul 10, 2009 | 2004 Hyundai Tiburon

2 Answers

My Brake lights don't work


2004 Rx8 kept blowing 15amp brake light fuse. Solution: wire going to rear lights was worn and frayed where it feeds through the left trunk lip on left side of trunk. This can be seen when you open the trunk lid. The wire routes by the trunk lid hinge. If the support connectors come loose, the wires are crunched by the hinge or lid. Re-splice, insulate, zip-tie, replace fuse and replace any blown bulbs.

Apr 13, 2009 | 2004 Mazda RX-8

1 Answer

Brake light on every time.


Hi,

Check the foot pedal switch first to see if is working correctly and not stuck, and that the pedal actually disconnects when returned.

If this is ok, you will have to trace the live feed back to the source, starting at the bulb, and working back.

Are you certain it is the brake light, and not a rear side light? These can be left on when the ignition is off, wheras brake lights usually can't

Jun 20, 2008 | 1991 Mazda 929

Not finding what you are looking for?
1991 Mazda 626 Logo

316 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...