Question about 2001 Volkswagen Golf

Open Question

I HAVE A THROTTLE VALVE CONTROL UNIT AND THE PART NUMBER 06A 133 064 J ON IT BUT I NEED TO FIND OUT THE ENGINE SIZE AND CODE IT WILL FIT TO. CAN YOU HELP?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car is a 2006 Nissan Altima I need an electrical throttle control actuator and my engine code is p0507


code p 0507 refers to idle speed (ISC) system-rpm higher expected ===causes ---wiring---ISC actuator --IAC valve--throttle motor ---throttle valve tight /sticking---ECM
it also refers to idle air control (IAC) system --circuit low ===causes ---wiring short to ground ---IAC valve --ECM
I would be wary of getting the throttle control actuator as all of the other possible causes indicate that it may not be that that is faulty

Jul 24, 2017 | Nissan Cars & Trucks

1 Answer

Location of IAC valve on 2003 2.0 sohc engine and how to clean


idle control valve is the unit that fits to the intake, it has wires on a plug that fit into the unit. as you not put a model number i cannot say were it would be as there are meany engine designs but when you put the throttle down the sencore moves and tell the engine its position and how much fuel and air to add depending on its position.

Jun 20, 2017 | Cars & Trucks

1 Answer

2003 sta fe hyundai give code 121


P0121 HYUNDAI - Throttle/Pedal Position Sensor/Switch 'A' Circuit Range/Performance

Possible causes - Faulty throttle position sensor - Throttle position sensor harness is open or shorted - Throttle position sensor circuit poor electrical connection - Faulty Engine Control Module (ECM) What does this mean? When is the code detected? Malfunction is detected when an excessively low or high voltage from the sensor is sent to ECM. Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P0121 Hyundai Description The throttle position sensor (TPS) responds to the accelerator pedal movement. This sensor is a kind of potentiometer which transforms the throttle position into output voltage, and emits the voltage signal to the Engine Control Module (ECM). In addition, the sensor detects the opening and closing speed of the throttle valve and feeds the voltage signal to the ECM. Idle position of the throttle valve is determined by the ECM receiving the signal from the throttle position sensor. This sensor controls engine operation such as fuel cut. On the other hand, the Wide open and closed throttle position switch, which is built into the throttle position sensor unit, is not used for engine control.

Nov 20, 2016 | Hyundai Cars & Trucks

1 Answer

Will not stay crank


You need to have it analyzed with a scan tool that can check engine sensor data parameters . This problem could be from any number thing's . Could need throttle plate cleaning ,EGR valve pintle sticking , IAC - idle air control passages an seat carboned up , Mass air flow sensor dirty , An intake manifold vacuum leak .How does it run other then your stalling problem ? how many miles on the vehicle ? What make , model an year vehicle ? What size engine does it have ? Does it have electronic throttle control ? Is the check engine light on or any other lights ?

Oct 20, 2015 | Cars & Trucks

3 Answers

COULD THE GAS PEDAL CABLE CAUSE THIS CODED PO507 to be high


Extracted from Engine-Codes.com

Code P0507

Possible causes

- Dirty throttle body

- Electric throttle control actuator misadjusted or damaged

- Faulty Electric throttle control actuator

- Intake air leak

- Poor electrical connection to the Intake Air Control (IAC) valve


help.jpg What does this mean?

Tech notes

If there are no intake leaks, clean throttle body, adjust engine idle and erase engine code. If the code comes back you may have to replaced the Electric Throttle Control Actuator (Motor) to repair the problem.



There is a factory service bulletin for the following Chevrolet models:



2006-2008 Chevrolet Trail Blazer

2007-2008 Chevrolet Avalanche

2007-2008 Chevrolet Express

2007-2008 Chevrolet Silverado

2007-2008 Chevrolet Suburban

2007-2008 Chevrolet Tahoe

Chevrolet Factory Service Bulletin OBDII Code P0507


What does this mean?

When is the code detected?

Thi P0507 code sets when the Powertrain Control Module (PCM) detects an engine speed outside of the Idle Air Control (IAC) valve range of control.

Possible symptoms

- Engine Light ON (or Service Engine Soon Warning Light)

- Engine hard to start

- Rough or erratic idle speed

P0507 Chevrolet Description

The Idle Air Control (IAC) valve is a Powertrain Control Module (PCM) controlled stepper motor located on the throttle body. The stepper motor drives a valve pintle which protrudes into a passage that bypasses the throttle plates. The PCM commands the IAC valve pintle to extend to decrease the idle speed. The bypass air flow is reduced and the idle speed decreases as the pintle approaches its seat. The PCM retracts the IAC valve pintle away from its seat to increase the idle speed. The retracting of the IAC valve pintle allows more air to bypass the throttle plates. One of the PCMs uses for the IAC system is to maintain a desired idle speed. This DTC sets when the PCM detects an engine speed outside of the IAC\'s range of control.





Read more: http://engine-codes.com/p0507_chevrolet.html#ixzz3ObdI2chF

Jan 11, 2015 | 2001 Chevrolet Blazer

1 Answer

Engine light came out and give me the code P2135


P2135 FORD Description

Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement.


The throttle position sensor has the two sensors. These sensors are a kind of potentiometers which transform the throttle valve position into output voltage, and emit the voltage signal to the Engine Control Module (ECM). In addition, these sensors detect the opening and closing speed of the throttle valve and feed the voltage signals to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and the ECM controls the throttle control motor to make the throttle valve opening angle properly in response to driving condition


Read more: http://engine-codes.com/p2135_ford.html#ixzz2LBgiF38q

Feb 17, 2013 | 2005 Ford Explorer

1 Answer

Code p1506


P1506----Idle Air Control (IAC) Overspeed Error

Disconnect the Valve,if you get no change in idle
the valve is stuck or bad

Then clean or replace as required

Near base of throttle body (maybe,got nothing to go by)

You provided no info on vehicle problem
or any vehicle year,engine size nothing

Oct 06, 2012 | Cars & Trucks

2 Answers

My monte carlo has code p0507 what is it and how can i fix it


possible causes
- Dirty throttle body
- Electric throttle control actuator misadjusted or damaged
- Faulty Electric throttle control actuator
- Intake air leak
- Poor electrical connection to the Intake Air Control (IAC) valve
solution !!!
If there are no intake leaks, clean throttle body, adjust engine idle and erase engine code. If the code comes back you may have to replaced the Electric Throttle Control Actuator (Motor) to repair the problem.

Jan 28, 2011 | 2000 Chevrolet Monte Carlo

1 Answer

What is the 1987 pontiac fiero gt v6 check engine light code list?


CODE 12- NO DISTRIBUTOR REFERENCE PULSES ECM. CODE 13- OXYGEN CIRCUIT. CODE 14- COOLANT SENSOR HIGH TEMP CODE 15- COOLANT SENSOR LOW TEMP. CODE 21 - THROTTLE POSITION SENSOR VOLTAGE HIGH.CODE 22 - THROTTLE POSITION SENSOR VOLTAGE LOW.CODE - 23 MIXTURE CONTROL SOLENOID.FOR CARBURETOR ENGINE. CODE 24 -VECHICLE SPEED SENSOR. CODE 32 - BARO CIRCUIT LOW.CODE 32 - FUEL INJECTED EGR VALVE VACUUM SWITCH SHORTED TO GROUND.OR EGR VALVE SOLENOID CIRCUIT OPEN. CODE 33 - MAP SENSOR.CODE 34 - VACUUM SENSOR OR MAP SENSOR.CODE 35 - IDLE SPEED CONTROL. CODE 41 - EST CIRCUIT. CODE 42 - ELECTRONIC SPARK TIMING.CODE 43 - ELECTRONIC SPARK CONTROL UNIT. CODE 44 - LEAN EXHAUST.CODE 45 - RICH EXHAUST. CODE 51 - PROM OR MEM CAL.CODE 52 - CALPAK. CODE 53 -EGR VALVE CARBURETED ENGINE THE EGR VALVE VACUUM SENSOR HAS RECEIVED IMPROPER EGR VACUUM. CODE 54 - M C SOLENOID CARBURETED ENGINE MIXTURE CONTROL SOLENOID SHORTED OR FAULTY ECM.CODE 54- FUEL INJECTED ENGINE FUEL PUMP VOLTAGE IS LOW.CODE 55 - ECM MAKE SURE PCM GROUND CONNECTIONS ARE TIGHT.IF OKAY.REPLACE THE ECM.

Mar 27, 2010 | 1987 Pontiac Fiero

Not finding what you are looking for?
2001 Volkswagen Golf Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...