Question about 2002 Land Rover Freelander

Open Question

No brake lights fuses checked and bulbs new brakepedle switch fited

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 grand Cherokee Laredo v8 all my brake lights went out checked the bulbs fuse and brake switch all are good the tail and signal lights are good. what should I do nextto fix the problem


Have you checked the brake light fuse to see if there is power at the fuse and out of the fuse, also check the brake light switch for power in and out when the pedal is pressed, do that and get back to me.?

Oct 26, 2016 | 2000 Jeep Grand Cherokee Laredo

1 Answer

Head lights work brake lights don't, have changed brake switch and bulbs and checked fuses


When you say you checked the fuse, are you getting power in and out of it and the brake light switch ?

Jan 04, 2013 | 2003 Jeep Liberty

1 Answer

Brake light does not go on, fuse ok new bulbs stil no brake light when brakes are applied


check both fuse boxs if ok check the break light switch on stearing colum may be unpluged or bad

Jan 29, 2012 | 2000 GMC Sierra

1 Answer

No brake lights 2005 suzuki reno all other lights operational


Have you checked the fuse for the brake lights? if not do so and then check the brake light switch mounted to the brake pedal, then check bulbs. Even new bulbs can go out!
Check the manual for fuse location for the brake lights.

Feb 04, 2011 | Suzuki Reno Cars & Trucks

1 Answer

2004 f150 heritage. Third brake light works but tthe two lower brake lights won't work. New bulbs. Any ideas?


check fuses in both fuse panels, then check brake light switch third brake light works off of brake switch too but diferent wire

Oct 27, 2010 | 2004 Ford F150

2 Answers

Brake lights don't work


This sounds like a bad brake light switch, this switch is located on the bracket that holds brake pedal,you can test for power at switch,also if you remove connector and jump terminals with a wire and see if lights lite, if lights light then switch is bad,

May 27, 2010 | 2006 Hyundai Sonata

2 Answers

No brake lights 1990 ford f 150


First, check fuses. If the fuse for tail and brake lights is OK, check the bulbs. If they are OK, you need a new brake light switch, which attached to the brake pedal under the dash. The part should be less than $20. These are a common replacement item on older fords.

Dec 20, 2009 | 1990 Ford F150

3 Answers

Brake lights do not work All bulbs have been replaced.


Troubleshooting Procedures - Read Completely Before Beginning
(American Car) All Brake Lights Not Working
  • Check System Fuse: A fuse is used to protect the brake light circuit from amperage overload. If the fuse has failed it will not allow the electrical current to continue to the brake lights. To check the fuse, first locate the brake light system fuse in the fuse panel which is either under the dash or under the hood in the power distribution center. Connect the test light to a ground like an engine or dash bracket and turn the ignition key to the "on" position. Using the test light probe both sides of the fuse. If the test light illuminates on both sides the fuse is ok continue onto the next step. If one side of the fuse illuminates the fuse has failed and needs to be replaced. If the fuse fails as soon as it is replaced or when you apply the brake pedal the brake light electrical circuit is shorted to ground. Rarely a system short can occur, a car repair manual is needed to find the wiring schematic for the brake light circuit. Once the brake light wiring has been located inspect and repair as needed.
  • Check Brake Light Bulbs: All cars have three brake light bulbs that create the brake light illumination affect. If all of these brake light bulbs fail no brake light operation will occur. I know what you're thinking, you might say all three brake lights at once? But in reality one brake light went out at a time and you did not notice. People only tend to notice something when they almost run into the back of your car to help persuade them to inform you the brake lights aren't working. Remove any of the brake light bulbs to confirm the bulb is ok or burned. After the bulb has been removed inspect the filament and replace if failed. If the brake light bulbs are ok continue to the next step.
  • Checking the Brake Light Switch: A control switch is used to connect the brake light electrical circuit. This switch is located near the brake pedal lever. Basic switches have just two wires, power in and power out to the turn signal switch. Use a test light that is grounded and with the key in the "on" position test for power at one side (wire) of the switch, then press the brake pedal while testing the opposite side (wire). It should illuminate the test light, if electrical power is connected through the switch go to the next step. If no power is detected through the switch the brake light switch has failed and replacement is required. If your car is equipped with more than two wires integrated into the brake light switch a car repair manual is needed to locate the proper brake light circuit wiring.

Jul 07, 2009 | 2000 Jeep Grand Cherokee

2 Answers

My tail lights work but the brake lights do not


The first thing that I would check is the fuse. If the fuse it ok then check the bulbs. Sometimes when one bulb goes out then the whole circuit just kind of shuts down. If this does not fix your problem then you are looking at a bad brake light switch. This is the switch that is located at the top of the pedal and it completes the circuit for the brake lights to turn on.

Jun 10, 2009 | 2001 Dodge Dakota

Not finding what you are looking for?
2002 Land Rover Freelander Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...