Question about 2005 Chevrolet Impala

Open Question

2005 chevy impala ignition switch instalation. How do you install one?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Fixe_You
  • 1800 Answers

SOURCE: 2005 chevy impala ignition switch

Ignition and Start Switch Replacement
Removal Procedure
2c23f8d.jpg Disconnect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.
Remove the steering column filler panel. Refer to Steering Column Filler Replacement .
Remove the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Remove the instrument panel (I/P) cluster trim panel. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Remove the ignition switch bolts.
Lower the ignition switch away from the instrument carrier.
Insert the key into the ignition lock cylinder. Turn the key to the ON/RUN position.
Depress the transaxle park/lock cable retainer to release. Pull to remove the park/lock cable from the ignition switch.
Important: The Passlock? electrical connector cannot be removed until the lock cylinder is removed.

Depress and hold the detent on the bottom of the ignition switch in order to release the ignition lock cylinder. Remove the ignition lock cylinder with the key.
d857e46.jpg Disconnect the Passlock? electrical connector.
Disconnect the electrical connectors.
4093e3a.jpg Important: Ignition switch lock cylinder that won't rotate or is seized.

Perform the following procedure if the ignition switch lock cylinder is seized or won't rotate.
12.1. Protect the immediate work area with suitable material such as clean shop towels or a clean fender cover.

12.2. Locate the surface for the ignition switch lock cylinder release button (2) on the plastic ignition switch housing and center punch a location (1) on the "rib" approximately 3/8 inch reward (toward the key entry end) from the cylinder release button.

12.3. Carefully drill a pilot hole through the plastic housing with a 1/8 inch drill bit.

12.4. Carefully drill a larger hole at the pilot location, and slightly into the ignition switch lock cylinder surface to break the release button retaining spring using a 9/32 inch drill bit.

12.5. Remove portions of the broken spring from the hole using a small suitable tool.

12.6. Grasp the ignition switch lock cylinder and remove it from the switch housing.

12.7. Remove any plastic "flash" from the drilling operation, and using compressed air blow out the ignition switch assembly.

12.8. Follow service manual procedures when cylinder cording is required. Refer to Key and Lock Cylinder Coding in General Information.

Installation Procedure
If the lock cylinder would not rotate or was seized, perform the following procedure:
1.1. Install the new ignition switch lock cylinder as required by rotating both the cylinder and the ignition switch to the ON position.

1.2. Push the ignition switch lock cylinder into the ignition switch housing until fully seated.

1.3. You may have to slightly depress the release button as the button passes by the 9/32-in hole previously drilled in the ignition switch housing.
9600af8.jpg Connect the electrical connectors.
Connect the Passlock? electrical connector.
Connect the park/lock cable to the ignition switchdd765ba.jpg Turn the key to the ON/RUN position. Install the ignition lock cylinder into the ignition switch. If you turned the key slightly while removing the lock cylinder, you may have to align the white colored ignition switch rotor (1) with the lock cylinder (2). You can rotate the ignition switch rotor (1) with your finger.
Remove the key
681874a.jpg Position the ignition switch to the instrument carrier.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

Install the ignition switch bolts.
Tighten

Tighten the bolts to 10 N?m (89 lb in).

Install the trim plate bezel to the I/P cluster. Refer to Trim Plate Bezel Replacement - Instrument Panel (I/P) Cluster .
Install the knee bolster bracket. Refer to Bracket Replacement - Knee Bolster .
Install the steering column filler panel. Refer to Steering Column Filler Replacement .
Connect the battery ground cable. Refer to Battery Negative Cable Disconnect and Connect Procedure in Engine Electrical.

rate me fix ya cuz this is the fix 100%

Posted on Aug 17, 2008

  • 4 Answers

SOURCE: radio unlock coed for chevy impala

• A module which communicates on the class 2 serial data circuit which supplies VIN information to the radio is replaced and not properly setup with the correct VIN information for that vehicle. The only way to unlock the radio is by using a scan tool.

Posted on May 15, 2009

  • 118 Answers

SOURCE: How do i change the Blower motor resistor on a 2005 chevy impala?

The blower motor resistor is located behind the glovebox mounted in the fan housing box under the dash.

Posted on Jul 20, 2009

adve1958
  • 246 Answers

SOURCE: 2005 Chevy Impala ignition switch stuck in off position

if it doesnt turn you have a worn out ignition cylinder, the only fix is to replace it, Code the ignition lock cylinder, if necessary

CAUTION:Perform the body control module (BCM) theft deterrent relearn procedure whenever you replace the ignition switch lock cylinder.

Posted on Sep 08, 2009

  • 1 Answer

SOURCE: installing ignition switch in 1990 chevy pickup

how to replace ignition switch in 1990 chev 1500 pickup long bed

Posted on Nov 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the purge valve solonoid


Shop for Where is the purge valve... on Google


2000?2001 Chevrolet Imp...
$22.04
Partsgeek.com 2000?2006 Chevrolet Imp...
$18.44
Partsgeek.com 2000 Chevy Impala Air Inje...
$80.95
Google Trusted Store1A Auto.c... 2000?02 Chevy Impala Air Inje...
$80.95
Google Trusted Store1A Auto.c... Standard 2005 Chevrolet Imp...
$26.69
Google Trusted StoreAutoParts... Search Results

    How To Install Replace Vapor Canister Purge Valve 3.4L ...

    ? 2:42
    https://www.youtube.com/watch?v=IPKnoxJCIWk
    Jul 9, 2014 - Uploaded by 1A Auto Parts
    http://www.1aauto.com/vapor-canister-purge-solenoid/i/1aemx00137 In ... How To Install Replace PCV Valve3.4L 2000-07 Chevy Monte Carlo ...

Dec 19, 2015 | 2000 Chevrolet Impala

1 Answer

How do I fix my 2005 chevy impala from shutting off on its own while driving it?after waiting for a few minutes it starts back up


check with your local chevy dealer,there is big recall on ignition switch,they will change it for free,and it only takes 90min to do it

Oct 06, 2014 | 2005 Chevrolet Impala

1 Answer

2005 Chevy impala brake pedal pulsation with brand new rotors installed


Is your ABS working properly? Under heavy braking the ABS should engage and 'pulse' the brakes on/off. It is normal to feel the brake petal flutter or pulse under your foot.

Under light braking there should be no pulsing as the ABS does not engage and you have changed the rotors and pads.

Nov 19, 2013 | 2005 Chevrolet Impala

1 Answer

I have a chevy impala 2001,i took it to the chevy house and they ran a dynostic and they told me it needed the ignition control module and the ignition swith,so i replaced them both but the car shows to be...


try this install the new key in the ignition switch. turn on the ignition switch to the on position for 10 minutes.when the system led lock light disappear.turn off the ignition switch for 5 seconds.then start the engine.still dont start.try this procedure few more times.if car still dont crank and you see the pad lock symbols.the dealership will have to reprogram the new key and body control module.

Apr 15, 2011 | 2003 Chevrolet Impala

2 Answers

2003 Chevy Impala periodically won't start


Try under the dash, attached to colum is a switch that the rod goes into from your ignition key switch, that may need to be adjusted tword your steering wheel just a touch, they go out of alignmnet from time to time

Sep 15, 2009 | 2003 Chevrolet Impala

3 Answers

2005 Chevy Impala ignition switch stuck in off position


Someone may have tried to steal the car and damaged the lock's internal pins. Replace the entire lock with new.

Sep 08, 2009 | 2005 Chevrolet Impala

2 Answers

Ignition Switch stuck in OFF position -Cannot Remove Key Cylinder


Yes the 2002 and 2005 are the same model and use the same lock.

2000-2005 Are all the same for anybody else needing similiar info.

Mar 30, 2009 | 2005 Chevrolet Impala

1 Answer

2005 chevrolet impala ignition swich


Even if you bypassed the switch, your steering would remain locked. In order to determine what is wrong with it, (other than the obvious) It will need to be taken apart. You will need a manual (such as Haynes, chilton etc) in order to do this safely and correctly.

Mar 24, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
2005 Chevrolet Impala Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...