Question about 2000 Dodge Caravan

1 Answer

Wipers inop new multifunction switch new wiper motor still dont work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

There is a relay in the fuse panel located next to the battery in the engine compartment. you will find the wiper relay there. replace it

Posted on Sep 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper control module location on a 2000 f250


Did you check the wiper relay's in the under hood fuse box ? There are two ,wiper run/park relay & wiper high low relay ! Also ,did you check fuse's ? fuse # 11 - 30amp location cental juction box . The wiper switch is a input to the GEM module . Generic electronic module . The module in most cases isn't the problem ! Learning how to test these electronic systems is , people do not know how to test so they just replace parts . What they should do is take the vehicle to ford certified Technician who has the knowledge and testing equipment to find an fix it .

The generic electronic module (GEM) receives inputs from the following:
  • multifunction switch
  • anti-lock brake control module (vehicle speed signal [VSS])
  • ignition switch
The GEM uses these inputs to control the outputs to the following:
  • windshield wiper high/low relay
  • windshield wiper run/park relay
  • windshield washer relay
  • rear wiper motor relay
  • rear window washer relay

  • GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1240 Wiper Washer Rear Pump Relay Circuit Failure GEM GO to Pinpoint Test K . B1241 Wiper Washer Rear Pump Relay Circuit Short to Battery + GEM GO to Pinpoint Test K . B1342 ECU is Defective GEM CLEAR the DTCs. REPEAT the GEM self-test. If DTC B1342 is retrieved, INSTALL a new GEM. REFER to Section 419-10 . B1431 Wiper Brake/Run Relay Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers stay on continuously, GO to Pinpoint Test C . B1432 Wiper Brake/Run Relay Circuit Short to Battery GEM GO to Pinpoint Test B . B1434 Wiper Hi/Low Speed Relay Coil Circuit Failure GEM GO to Pinpoint Test D . B1436 Wiper Hi/Low Speed Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test D . B1438 Wiper Mode Select Switch Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If both the windshield and rear window wipers are inoperative, GO to Pinpoint Test L . B1441 Wiper Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test C . B1446 Wiper Park Sense Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
    If the speed dependent interval mode does not operate correctly, GO to Pinpoint Test G .
    If both windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1450 Wiper Wash/Delay Switch Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
    If the wash and wipe function does not operate correctly, GO to Pinpoint Test F .
    If both the windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1453 Wiper Wash/Delay Switch Circuit Short to Ground GEM If the windshield wipers stay on continuously, GO to Pinpoint Test C .
    If the wash and wipe function does not operate correctly, GO to Pinpoint Test F . B1458 Wiper Washer Pump Motor Relay Circuit Failure GEM GO to Pinpoint Test F . B1460 Wiper Washer Pump Motor Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test F . B1473 Wiper Low Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
    If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E . B1475 Accessory Delay Relay Contact Short to Battery GEM REFER to Section 501-11 . B1476 Wiper High Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
    If the intermittent windshield wiper does not operate correctly, GO to Pinpoint Test E . B1611 Rear Wiper Mode Switch Circuit Failure GEM GO to Pinpoint Test H . B1614 Rear Wiper Mode Switch Circuit Short to Ground GEM GO to Pinpoint Test I . B1820 Rear Wiper Motor Up Relay Circuit Short to Battery + GEM GO to Pinpoint Test H . B1839 Rear Wiper Motor Circuit Failure GEM GO to Pinpoint Test H . - All other DTCs. GEM REFER to Section 419-10

Jun 06, 2017 | Ford F-250 Cars & Trucks

1 Answer

2005 ford escape wiper and washer has no power. cant hear it engage when on but was working a week ago. how can i troubleshoot it and find the fuse


Hi Justin , Do you know what a SJB - smart junction box is and where it is located on you escape ?
Windshield Wiper Operation
The smart junction box (SJB) supplies power to the multifunction switch from the SJB fuse 25 (20A) when the ignition switch is in the ON or ACC position. The multifunction switch supplies power to the windshield wiper motor for the HIGH or LOW/INTERMITTENT input, depending on the multifunction switch position selected. The SJB also supplies power directly to the windshield wiper motor from fuse 25 (20A) when the ignition switch is in the ON or ACC position for RUN/PARK operation. When the multifunction switch is in the LOW, HIGH, or INTERMITTENT position, power is supplied to the windshield wiper motor, which moves the wipers off the park position. Once the wipers are off the park position, an internal switch in the windshield wiper motor switches to the run/park position which directs power to the wiper switch then back to the wiper motor. This maintains power to the windshield wiper motor to complete the wipe cycle. When the cycle is complete, the internal switch in the windshield wiper motor switches back to the park position. If the multifunction switch is in the LOW or HIGH position, power is supplied from the multifunction switch and another wipe cycle starts. If the multifunction switch is in the INTERMITTENT position, the windshield wipers remain parked until the internal relay in the multifunction switch supplies power to the windshield wiper motor. The internal relay supplies power after a time delay that is determined by the 1 of 9 intermittent switch settings.

Jan 08, 2017 | 2005 Ford Escape

3 Answers

My f250 2003 wipers and pump dont work iv replaced switch and wiper moter fuses are good the 2 i could locate for wipers


Have you done a Probe Test on the vehicle? A Probe Light Tester can help you locate a short in your cars electrical system. To learn what a Probe Tester is and How to use it, watch the following video: https://www.youtube.com/watch?v=tXzKcEyIOq8

Dec 22, 2015 | Cars & Trucks

2 Answers

Where is the windshield wiper fuse located in the fuse box on a 06 crown victoria


drivers side inner fender under the hood, look in the owners manual for the number and amps. some are marked under the lid itself

Mar 19, 2015 | 2006 Ford Crown Victoria

2 Answers

Where is the fuse box for the wipers


It is under the dash panel right hand side , kick panel ? Fuse F1.1 10amp . an fuse F1.113 30 amp.
Visual Inspection Chart Mechanical Electrical
  • Windshield washer hoses
  • Wiper linkage
  • Multifunction switch
  • CJB fuses:
    • 1 (10A)
    • 38 (25A)
    • 113 (30A)
  • Circuitry
  • Windshield wiper motor
  • The windshield wipers are inoperative
  • Multifunction switch.
  • Circuitry.
  • Ignition switch.
  • Windshield wiper motor.
  • Go To Pinpoint Test A .
PINPOINT TEST A: THE WINDSHIELD WIPERS ARE INOPERATIVE Test Step Result / Action to Take A1 CHECK CIRCUITS 65 (DG) AND 1002 (BK/PK) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Key in ON position.
  • Measure the voltage between windshield wiper C125 pin 5, circuit 65 (DG), harness side and ground; and between windshield wiper motor C125 pin 8, circuit 1002 (BK/PK), harness side and ground.
    s3j~tr~en~file=a0039065.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to A2 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A2 CHECK CIRCUITS 57 (BK) AND 875 (BK/LB) FOR OPENS
  • Key in OFF position.
  • Measure the resistance between windshield wiper C125 pin 6, circuit 57 (BK), harness side and ground; and between windshield wiper motor C125 pin 3, circuit 875 (BK/LB), harness side and ground.
    s3j~tr~en~file=a0037610.gif~gen~ref.gif
  • Are the resistances less than 5 ohms?
Yes
GO to A3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A3 CHECK THE MULTIFUNCTION SWITCH
  • Disconnect: Multifunction Switch C202a.
  • Carry out the multifunction switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multifunction switch pass the component test?
Yes
GO to A4 .

No
INSTALL a new multifunction switch. REFER to Section 211-05 . A4 CHECK CIRCUIT 57 (BK) FOR OPEN
  • Measure the resistance between C202a pin 4, circuit 57 (BK), harness side and ground.
    s3j~tr~en~file=a0045222.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A5 .

No
REPAIR the circuit. TEST the system for normal operation. A5 CHECK CIRCUITS 56 (DB/OG), 58 (WH), 61 (YE/RD), AND 63 (RD) FOR OPENS
  • Using the following table, measure the resistance between the multifunction switch C202a harness side and the windshield wiper motor C125 harness side:

    Multifunction Switch C202a Windshield Wiper Motor C125 pin 7, circuit 56 (DB/OG) pin 10, circuit 56 (DB/OG) pin 3, circuit 58 (WH) pin 11, circuit 58 (WH) pin 5, circuit 61 (YE/RD) pin 1, circuit 61 (YE/RD) pin 1, circuit 63 (RD) pin 9, circuit 63 (RD)

    s3j~tr~en~file=a0045221.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to A6 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. A6 CHECK FOR CORRECT WIPER MOTOR OPERATION
  • Disconnect all wiper motor connectors.
  • Check for:
    • corrosion
    • pushed-out pins
  • Connect all wiper motor connectors and make sure they seat correctly.
  • Operate the system and verify the concern is still present.
  • Is the concern still present?
Yes
GO to A7 .

No
The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation. A7 CHECK THE WINDSHIELD WIPER MOTOR
  • Key in OFF position.
  • Disconnect: Windshield Wiper Motor C125.
  • Carry out the windshield wiper motor component test as described in this section.
  • Did the windshield wiper motor pass the component test?
Yes
The system is operating correctly at this time. Concern may have been caused by binding or incorrect pivot arm adjustment. REFER to Windshield Wiper Blade and Pivot Arm Adjustment in this section. TEST the system for normal operation.

No
INSTALL a new windshield wiper motor. REFER to Windshield Wiper Motor in this section. Hope this helps !

Feb 16, 2015 | 2002 Ford Expedition

2 Answers

Wiper dont work wiper motor is new but still does not work


Check power and ground circuits at wiper motor to see if they are there, key on, wiper switch on if not check BCM output for the wiper you may have to take it into a shop for that to scan to see if the output is there from the BCM as this controls the wiper through the multifunction switch.

May 01, 2014 | 1999 Plymouth Grand Voyager

1 Answer

Wiper dont work


Check all your fuses and breakers first. With the ignition turned to run check that you have power at the WCM, wiper control module, check the multifunction switch the wipers run off of, check wiper motor or linkage under the plastic cowling under the wiper blades, comes off easily with a few screws and clips.

Mar 16, 2013 | 1997 Mercury Grand Marquis

2 Answers

Rear wiper stopped working


my 2004 expedition had same problem, if you take apart the shaft that goes thru the glass it will be full of dirt, clean ,lubricate and reinstall, you may have to replace the O-ring on the shaft. a 20 minute job, very easy fix

Feb 25, 2009 | 2004 Ford Expedition

Not finding what you are looking for?
2000 Dodge Caravan Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...