Question about 1983 Ford Fairmont

Open Question

How to remove Radiator fan pulley - 1983 Ford Fairmont

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: how do i remove fan

there are 8 10mm. bolts 4 on top 2 on each side this is a two part shroud also pull out trans dipstick and oil dip stick .it still wont be easy to get out you have to finagle the shroud out .are u doing water pump

Posted on Jan 30, 2009

Ad
Ford007
  • 131 Answers

SOURCE: i believe the bearing on my waterpump is bad.

You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off.

Posted on Mar 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 dodge intrepid sxt 3.5 over heated replaced the thermostat and still over heats might be water pump where is it located and what is in volved in fixing this


The water pump is located in the front of the engine & is driven by the timing belt. So if you go in there you might as well replace the belt and tensioners if needed.
Drain the cooling system (turn the radiator drain 1 full turn only)
  1. Remove the upper radiator hose
  2. Remove the top radiator support
  3. Remove the two 10mm head bolts from either side of the radiator and gently pull the top of the radiator forward to gain a little more room
  4. Remove the four 10mm head bolts holding the cooling fan module to the radiator . Remove the four clip nuts and the cooling fan electrical connector and lift the fan module out of the vehicle
  5. Loosen and remove the drive belts and remove the three 13mm head bolts holding the alternator belt tensioner pulley to the timing cover
  6. Remove the three piece timing belt cover (the lowest piece can be accessed through the crankshaft pulley by turning the pulley and removing the bolts)
  7. turn the crankshaft pulley and line up the timing marks on top dead center
  8. Remove the timing belt tensioner two 13mm bolts and remove the tensioner (If the tensioner pulley wheel is made of plastic you will want to purchase a revised steel tensioner pulley) . Put the tensioner in a suitable vise to compress it and install a small allen wrench from the front to hold it in place (close the vise slowly to compress the tensioner)
  9. (If need be) Remove the plastic tensioner pulley (the 15mm head attaching bolt can be removed without removing the crankshaft pulley)
  10. The timing belt can easily be slipped under/around the crankshaft pulley by slightly bending it to the outside of the timing belt housing on the drivers side and working it with your hand through the crankshaft pulley . No excessive force is needed to do this and be sure to clean the area well prior to installing the new belt
  11. With the belt removed , remove and replace the water pump . Coat the gasket with a little RTV silicone and clean the gasket mating surface well
  12. Install the timing belt in the opposite direction as removed . Make sure that all the timing marks are lined up .
  13. Reinstall the timing belt tensioner

    Note: There are several different length bolts used, so pay attention to where they are removed from, they must be installed in the same placement.

    I hope this information was helpful.

Sep 17, 2011 | 2003 Dodge Intrepid

1 Answer

How to replace a radiator on a1994 toyota land cruiser


dak408_129.gif

  1. Disconnect battery ground cable.
  2. Drain engine coolant.
  3. Remove battery and tray,
  4. Remove radiator grille
  5. Disconnect No. 3 water bypass hose.
  6. Disconnect radiator inlet hose.
  7. Disconnect coolant reservoir hose.
  8. Loosen water pump pulley mounting bolts.
  9. Loosen lock, pivot and adjusting bolts of alternator and remove drive belts.
  10. Disconnect oil cooler hose from clamp on fan shroud, then remove shroud.
  11. Remove water pump pulley mounting nuts.
  12. Remove fan with fluid coupling, water pump pulley and fan shroud.
  13. Disconnect transmission oil cooler hoses.
  14. Disconnect radiator outlet hose.
  15. Remove radiator brackets, then the radiator.
  16. Reverse procedure to install.

Dec 11, 2010 | 1994 Toyota Land Cruiser

1 Answer

Installing water pump in 97 cavalier 2.2


Hi. Here's the proceudere on how to replace the water pump of your 97 Chevy Cavalier.


•1
Drain the cooling system. Place a large oil drain container under the drain fitting located on the bottom of the radiator. Turn the drain fitting counterclockwise until fluid is draining from the radiator. Use a pair of pliers to turn the drain fitting if you cannot turn it by hand. Turn the fitting clockwise to tighten it after all of the fluid has drained from the radiator.
•2
Remove the cooling fan. Disconnect the electrical connection from the fan motor. Remove the bolts holding the fan assembly to the radiator support with a ratchet wrench. Pull the fan assembly up from the engine compartment and remove it.
•3
Remove the serpentine belt. Place a wrench over the belt tensioner and rotate the tensioner to release the tension on the belt. Pull the belt off the pulleys and remove it from the vehicle.
•4
Remove the water pump pulley. Place a screwdriver behind the pulley to lock it in place while removing the pulley mounting bolts with a ratchet wrench.
•5
Disconnect the coolant hoses running to the water pump.
•6
Remove the water pump mounting bolts with a ratchet wrench or wrench and remove the water pump from the vehicle.
•7
Clean the mating surfaces of the engine block and new water pump with a towel saturated with lacquer thinner.
•8
Apply a thin layer of RTV sealer to both sides of the new water pump gasket and place the gasket on the new water pump.
•9
Place the water pump against the engine block and finger tighten the water pump mounting bolts to hold the pump in place. Tighten the bolts with a torque wrench to 18 foot-pounds.
•10
Place the pulley on the water pump and install the water pump pulley mounting bolts with a ratchet wrench.
•11
Attach any hoses previously disconnected from the water pump.
•12
Install the serpentine belt. Route the belt over the pulleys according to the routing diagram in the engine compartment. Place a wrench over the belt tensioner and rotate the tensioner to tighten the tension on the belt.
•13
Install the cooling fan. Gently lower the cooling fan in position and install the mounting bolts attaching the fan assembly to the radiator support with a ratchet wrench. Attach the electrical connection to the fan motor.
•14
Refill the cooling system to the appropriate level, start the vehicle and check for leaks around the water pump.

All the best!

Nov 10, 2010 | 1997 Chevrolet Cavalier

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

1 Answer

Can't pull the radiator uot of my 1999 BMW 528i, t...


You gotta remove the fan and shround. Fan nut is 1.250" wrench. Fan nut is left handed thread. this means rightey loosey, lefty tightey. Go get the special tool to hold the fan pulley bolt heads. While you are turning the fan nut clockwise to loosen the special tool holds two of the fan pulley bolt heads to keep the fan pulley still. And voila, off comes the fan. then you can remove the shroud with it. Then you can remove the radiator. Fun job. I've got it down to 8 minutes.

May 19, 2010 | 1999 BMW 5 Series

1 Answer

How do i change a water pump on 1996 grand cherokee limited V8


I'll assume you have a 4.0l

The 4.0L engine is equipped with a reverse rotation (counterclockwise) water pump. The word REVERSE is stamped or imprinted on the cover of the viscous fan drive and on the inner side of t he fan. The letter R is stamped onto the water pump impeller. When replacing water pump, ensure proper pump is installed. Installation of the wrong water pump will cause engine overheating.

NOTE:On models with 4.0 L engine, front grill must be removed to access radiator draincock. Draining cooling system can be accomplished by removing drain plug from side of block as well as by loosening radiator draincock. Drain plug is located on lower left side of engine block.

Disconnect negative battery cable. Drain cooling system. Disconnect electric cooling fan connector. Remove electric cooling fan and electric fan shroud assembly (if equipped).
Loosen, but do not remove, 4 water pump pulley-to-water pump hub bolts and 4 viscous fan-to-idler pulley nuts. Remove accessory drive belt. Remove 4 viscous fan to idler pulley nuts, and remove fan and shroud together.
Remove 4 water pump pulley bolts and remove pulley. Remove power steering pump and bracket. Disconnect heater hoses and lower radiator hose at water pump. Remove 4 water pump retaining bolts. Remove water pump.

to install just reverse procedures

Apr 05, 2010 | 1996 Jeep Grand Cherokee

1 Answer

I believe the bearing on my waterpump is bad. while driving the fan began rubbing the shroud and eventually wedged against the waterpump pulley. before removing the radiator,shroud and hoses i checked...


You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off.

Feb 22, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How to change water pump (1997 sonoma)


The text below is from the GM Service manual 4.3L V6 Engine
Water Pump Replacement (4.3L)
Removal Procedure
Drain the cooling system. Refer to Draining and Filling Cooling System .
Loosen the water pump pulley bolts.
Remove the cooling fan and clutch assembly.

Tools Required
J 46406 Fan Clutch Wrench

Removal Procedure
Remove the upper fan shroud.
Remove the fan clutch from the water pump in a counterclockwise direction using the J 46406 .
Remove the fan clutch assembly.
Remove the drive belt. Refer to Drive Belt Replacement Remove the water pump pulley mounting bolts.
Remove the water pump pulley.
Remove the radiator outlet hose clamp from the water pump.
Remove radiator outlet hose from the water pump.
Remove the water pump mounting bolts.
Remove the water pump from the engine.
Remove the water pump gaskets.
Clean the water pump gasket mating surfaces.
Installation Procedure
Install the water pump gaskets.
Install the water pump to the engine.
Apply a sealer (GM P/N 12346004) to the bolt threads.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Install the water pump mounting bolts.
Tighten
Tighten the mounting bolts to 41 N·m (30 lb ft).
Install the radiator outlet hose to the water pump.
Install the water pump pulley.
Install the water pump pulley bolts.
Tighten
Tighten the water pump pulley bolts to 25 N·m (18 lb ft).
Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical - 4.3L.
Install the fan clutch assembly.
Fill the radiator cooling system. Refer to Draining and Filling Cooling System .
Inspect the cooling system for leaks.

Oct 01, 2009 | 1997 GMC Sonoma

1 Answer

F150 1990 waterpump replacrment where do I start


5.0L, 5.8L and 7.5L Engines
See Figures 1, 2, 3, 4 and 5


0900c15280262ad7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Removing the pulley from the water pump shaft may be easier if you use belt tension to hold the pulley


0900c15280262ad8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Loosen the clamp and remove the hoses at the water pump


0900c15280262ad9.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: Unbolt the water pump from the timing chain cover


0900c15280262ada.jpg enlarge_icon.gifenlarge_tooltip.gif : Remove the water pump from the timing chain cover

: Make sure the gasket mating surfaces are clean and dry
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts securing the fan shroud to the radiator, if so equipped and position the shroud over the fan.
  2. Disconnect the lower radiator hose, heater hose and by-pass hose at the water pump. Remove the drive belt(s), fan, fan spacer and pulley. Remove the fan shroud, if so equipped.
  3. Loosen the alternator pivot bolt and the bolt attaching the alternator adjusting arm to the water pump. If applicable, remove the power steering pump bracket from the water pump and position it out of the way.
t may be easier to remove the pulley from the water pump shaft by using belt tension to hold the pulley prior to removal.
  1. Remove the bolts securing the water pump to the timing chain cover and remove the water pump.
To install:
  1. Coat a new gasket with sealer and install the water pump. Tighten the bolts to 18 ft. lbs. (24 Nm).
  2. Install the power steering pump bracket.
  3. Connect the lower radiator hose, heater hose and by-pass hose at the water pump.
  4. Install the fan shroud, if so equipped.
  5. Install the pulley, fan spacer, fan and drive belt(s).
  6. Fill the cooling system.

Apr 07, 2009 | 1990 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...