Question about 2000 Chevrolet Camaro

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Posted on Sep 06, 2009

  • jaxbusbe Sep 06, 2009

    Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal goes to the floor but when i pump it it will come back


bad mc clutch
bad slave clutch.
can be either or both,
the hydralic clutch actuator has no adjustment other suz, older had cables, its no cable system as other states.
its auto adjusting
1: is Dot3/4 fluid leaking on either side of MC (clutch master cylinder)
2: is dot3/4 fluid leaking from the slave?
bingo fail for either leaking.
if no leaks the MC is bad, or not full of fluid.
3: does the fluid drop each weak, ( bingo for leaks)

Apr 14, 2013 | 2008 Suzuki Grand Vitara

2 Answers

I replaced the clutch master cylinder and the braided brake line in a 2000 camaro ss and I'm trying to bleed the system. I know how to do it but I've done the procedure 20 times and there is still no


You may have got a bad master cylinder.It happened to me before.I had to get 3 of them before i got a good one.Mine was on a full size jeep though.

Mar 21, 2013 | Cars & Trucks

1 Answer

Hi, my clutch stays to the floor. does the master or the slave push pedal up?


the clutch pressure plate return springs pushes the fluid back up the line through the slave and then the master to return the pedal. Both the Slave and the Master should be replaced at once.

Feb 04, 2011 | 1999 Chevrolet Camaro

1 Answer

Is there any way to adjust the clutch on 2006 Kia Spectra5?


YOU HAVE HYDRALIC CLUTCH WHICH IS A CLUTCH MASTER CYLINDER WITH SLAVE CYLINDER.IF YOU HAVING CLUTCH PROBLEMS.CLUTCH IS WORN AND SLIPPING OR YOU HAVE LOW FLUID LEVEL IN CLUTCH MASTER CYLINDER.WHICH CAUSES AIR GET IN HYDRALIC SYSTEM.CAUSING CLUTCH PROBLEMS.IF CLUTCH MASTER CYLINDER IS LOW ON FLUID.CHECK HYDRALIC LINE ON SLAVE CYLINDER TO CLUTCH MASTER CYLINDER FOR FLUID LEAKS.

Aug 03, 2010 | 2007 Kia Spectra5

1 Answer

Clutch pedal goes to floor and stays 1999 Nissan sentra 1.6 changed clutch presssure plate and throwout bearing surfaced flywheel has cable clutch have tried adjusting all ways


ON A 2000 MAX 6 CYLINDER HAS CLUTCH MASTER CYLINDER AND SLAVE CYLINDER, CHECK FLUID LEVEL AND BLEED CLUTCH SYSTEM AT SLAVE CYLINDER BLEEDER. HAVE NOT HEAR OF CABLE CLUTCH SYSTEM. ONLY HYDO.& LINKAGE. GOOD LUCK

Nov 05, 2009 | 2000 Nissan Maxima

2 Answers

Clutch pedal stays to the floor and car is now stuck in neutral. Can raise the pedal with hand but will not raise on it's own


clutch hydralics is gone, meaning you have a leak, check clutch master cylinder, see if its empty, if so refill and pump pedal sevarel time may have to lift by hand sometimes then look for a leak,most times it the slave cylinder,thats what pushs clutch fork to disengage clutch. hope this is helpful good luck.

Oct 15, 2009 | 2003 Pontiac Sunfire

2 Answers

Need to bleed clutch to get peddle


try to vacuum bleed the system at the master most hand vacuum kit come with adapters to fit over the master reservoir otherwise the system may need a new master or you may have a leak

Sep 04, 2009 | 1994 Dodge Stealth

2 Answers

Clutch pedal stuck to the floor stick shifter will not go into gear while truk is running


try pulling pedal up, does it drop str8 to the floor,if yes problem in hydralic clutch like clutch master cylinder or slave cylinder,if pdel stays up appears to be ok then the clutch may need replacing

Mar 06, 2009 | 1995 Ford F150 Styleside Regular Cab

1 Answer

Clutch pedle stays down


if you have a hydralic clutch usually the pedal staying on the floor indicates air in the clutch lines. if so check 4 leaks at the filler and at the slave cylinder. however just bleeding the clutch system may temporarily fix your issue

Jan 20, 2009 | 2004 Oldsmobile Alero

1 Answer

Clutch pedal won't disengage clutch


make sure fluid is full... then pump the pedal with it NOT RUNNING as many times really fast as you can.. try it after that, if it works then you need either a clutch MASTER cyliner and/or a SLAVE cylinder.. MOST likely being the slave cylinder. if the pumping action doesnt cause it to disengage then you have a burnt out clutch. The system is hydralic and takes regular DOT3 brake fluid in the small resevoir under the hood next to the brake master cylinder...
The slave cylinder being bad would mean you have to removed the transmission and install a new slave cylinder... thats the most common issue with those around that mileage...

Nov 24, 2008 | 1998 Chevrolet S-10 Pickup

Not finding what you are looking for?
2000 Chevrolet Camaro Logo

1,170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...