Question about 1995 Mercedes-Benz SL-Class

1 Answer

I have a 1995 sl320 i can't get the gas door open. and when i unlock the car remotely the light flashes but the doors don't lock or unlock remotely.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

Inside the trunk there is a emergency fuel door release you can pull that will open the door. After you get it open look at the post that the locking pin goes through when the door is closed. Shoot some lubricant spray in to the hole the pin come out from and that should loosen up the pin to slide smoothly.They get stuck with age.

Posted on Sep 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a 1996 Subaru Impreza L 4dr 5speed AWD that runs and starts fine but when I was installing fog lights i noticed that there appears to be an alarm hooked up (it says "code alarm elite DM...


Battery Constant 12v+ Positive Wire (+): Black/Yellow
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Blue/Red
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Red
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Red/Yellow
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Red
Parking Light Positive Wire Location: Low In Drivers Kick Panel

Power Door Lock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Lock Negative Wire Location: To Drivers Door Only

Power Door Unlock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Unlock Negative Wire Location: To Drivers Door Only

Door Trigger Negative Wire (-): Red/White
Door Trigger Negative Wire Location: In Black Plug, Above Hood Release

Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A

Horn Negative Wire (-): Red/Green
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Black/Blue
Tachometer Wire Negative Wire Location: At ECM, Under Drivers Side Dash

Brake Light Positive Wire (+): White/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal

CODE ALARM SYSTEM

Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000

codealarmremote2.jpgBattery GP-23A

Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm onlyPress the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter "UNLOCK" button once OR turn the ignition switch to the "ON" position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.

Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button.
Press lock (left) button the remotes to be programmed. The door locks will cycle one time. Exit programming mode by releasing Programming button under dashboard and turning key to off.


codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.

Jan 05, 2011 | Subaru Impreza Cars & Trucks

1 Answer

I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction imp05keylessremote1.jpg
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

1 Answer

Doors not locking when open only when closed, relays cicking


You can't lock the car when any of the doors are open EXCEPT with the door "Lock" button on the driver's side door. The remote will not lock the car when any of the doors are open.

May 25, 2009 | 1995 Jeep Grand Cherokee

2 Answers

LED lights for locking and unlocking flash at the same


that system is part of D.A.S. 2( driver authorization system verson 2). the lights in the mirror will blink red when lock and green when unlock. during the self diagnoses portion they will blink simutanilusly when the remote key batteries are low and alternating when there is a malfunction with the key or other part of the driver authorization. it sounds like your remote key central locking batteries are low.

Apr 15, 2009 | 1995 Mercedes-Benz C-Class

1 Answer

Remote locks the doors but will not unlock doors or trunk Battery


It is entirely possible that the unlock button on the remote is worn such that it is not making contact. I've seen this happen many times, as the unlock button is pressed so much more than lock. You might try to reprogram the remote first before you look into getting a new remote. The procedure goes like this. Close and lock all doors Key in and out of the ignition 6 times, hazard lights should flash twice Turn key into accessory or on position Unlock and lock doors with drivers switch Press lock or unlock on remote Hazards should flash again to verify recognition turn key off  manually unlock door and then open and shut it.  you should then be able to test remote. 
The key to the procedure is doing step two quickly Hope this helps, if not you may need another remote or see dealer.

Apr 11, 2009 | 2004 Infiniti I35

3 Answers

Door lock 2004 jetta wagen


If remote locks and unlocks driver door but does not unlock passenger doors,then follow the advice above:
Get in the car using the key to unlock the doors. From the passenger side lock and unlock your doors using the button on the passenger door. Get out and the remote should now unlock all the doors with 2 presses.
Worked perfectly for me after several other suggestions (and dealer) failed.

Nov 07, 2008 | 2004 Volkswagen Jetta

1 Answer

Programming a 1995 toyota avalon key fob


To program a remote... note that you must not delay more than 10 seconds between any of the operations.

Driver's door open, all other doors closed, key removed from the ignition switch.

Insert key into ignitions switch, then remove it.

Press LOCK then UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times.

close and re-open drivers door.

Press LOCK and UNLOCK on the vehicle door lock control switch at 1 second intervals 5 times

Insert Key into ignition switch.

Switch ignition ON and OFF once to program a remote transmitter code while retaining the original codes or twice to program a remote transmitter code while erasing the original codes. three times to check how many remote transmitters are currently registered, or 5 times to erase all registered codes.

Remove Key from ignition switch.

System should now lock and unlock vehicle. Once, twice or five times depending which mode has been selected. It will lock and unlock one to four times slowly, to indicate the number of remote transmitters registered if you chose option 3.

Press and hold remote transmitter LOCK and UNLOCK buttons at the same time.

Press LOCK remote button for 1 second: System should now lock and unlock vehicle once to confirm, twice to indicate registration has failed.

NOTE: to exit programming mode, close drivers door or insert key in the ignition.

NOTE: a maximum of 4 remote transmitters can be programmed

Oct 13, 2008 | 1995 Toyota Avalon

2 Answers

Security system not working as it used to


i read this on the subaru tech bulletin page
i had the same problem - apparently i had inadvertently put the system into "valet" mode
to get back to normal, unlock with remote - open drivers door - hold down the unlock button on your remote for 2-3 sec - the flashing light will go out and your system should be back to normal
it's too bad the manual doesn't supply information about activating and deactivating "valet" mode
good luck

Oct 13, 2008 | 2001 Subaru Forester

2 Answers

Program keychain remote


enter car use power door to lock doors place key into switch & pull in & out until flashers flash then turn key to acc. hit any button on remote the flashers will flash turn key off & remove unlock doors with power door lock switch open door the remote sould be programed

May 18, 2008 | 1995 Nissan Maxima

Not finding what you are looking for?
1995 Mercedes-Benz SL-Class Logo

274 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...