Question about 1988 Nissan Maxima

Open Question

How do i install left and right drive axels on my 1998 nissan maxium

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace right front axel seal 2001 pathfinder


Hi,if you are talking about the drive shaft cv boot,there is a vidio on you tube showing how to change the drive shaft same perseger,hope this is helpfull,all the best,its a easy fix.

Oct 03, 2015 | 2001 Nissan Pathfinder

1 Answer

I have a 1992 nissan terrano only my left rear wheel is getting power in 4WD


C clip that retains axel is broken or came off. Or the axel is bad.

Jan 12, 2014 | Nissan Cars & Trucks

2 Answers

My 1998 hyundai excel glx has a clicking sound front left wheel when turning


that would most likely be your drive axel when they go bad they click when you turn the steering wheel

Feb 04, 2013 | Cars & Trucks

1 Answer

2004 nissan maxium code u1000


Trouble Code: U1000

Controller Area Network Line Malfunction

Possible Causes:


CAN connector is damaged or is disconnectedCAN communication line is open, shorted to ground or to powerOne of the modules is shorted and pulling the CAN voltage low

Jan 27, 2013 | 2004 Nissan Maxima

1 Answer

Need to replace speed sensor on a 1998 nissan quest mini van


the sensor is located on the trans housing above the right axel where it inters the trans

Jul 25, 2012 | 1998 Nissan Quest

1 Answer

Need radio wiring diagram


Below is the diagram you requested, courtesy of: http://the12volt.com



1998 Nissan Frontier Stereo Wiring


Constant 12V+ Pink

Switched 12V+ Blue

Ground Gray

Illumination Red/Blue

Dimmer Red/Yellow

Antenna Right Front

Front Speakers 6 1/2" Doors

Left Front (+) Pink

Left Front (-) Blue

Right Front (+) White

Right Front (-) Black

Rear Speakers 5" Side Panels

Left Rear (+) Light Green

Left Rear (-) Purple

Right Rear (+) Blue

Right Rear (-) Pink

Feb 25, 2011 | 1998 Nissan Frontier

1 Answer

Heard clunking from front end when 4 wheel was engaged and now no 4 wheel drive


if your truck has cvaxels which is only if it is independent front end your cv axel is bad. if you have straight axel it sounds like you have a bad universil joint its right behind your hub where the brake system is check both sides

Feb 02, 2011 | 1998 Dodge Ram 1500 4WD

1 Answer

I'am trying to take the transaxle out of the transmission to fix an oil leak


Remove the wheel cover and loosen the drive axel hub nut. loosen the the wheel lug nuts raise the vehicle and support it well. NOTE: you will have to be working under the car be very careful. remove the drive axel hub nut. To prevent the hub from turning, insert a screwdriver thru the brake caliper and into one of the cooling slots on the rotor. remove the control arm-to-steering knuckle. Check for the ABS sensor and remove it out of your way. Separate the drive axel from the hub. If stuck remove the brake caliper and rotor. Push the axel out of the hub with a puller or you can use a good solid broom handle and drive it out. If you are removing the right side axel you will need a slide hammer and adaptor to separate the axel from the trans. If you are removing the left side, carefully pry the axel out of the trans. with a large pry-bar positioned between the inner CV joint and the trans. case. Use the subframe as a pivot point. Hold the CV joints so they do not separate inside the rubber if going to reuse them. Lubricate the new seal with multi-purpose grease before you install it.

May 05, 2010 | 2001 Chevrolet Impala

2 Answers

My idler pulley is making a squeaky light grinding niose.


Any Auto Parts store or even a Wallmart may have a WD 40. I would first try to spray this behind or right where you see the Axel of this Idle pulley.
Unfortunately it may be getting old and dried out.
If you have any grease or even - sounds funny - Vaseline - try smearing this on where the Axel meet's the round pulley.
Blessings,
A/V Guy

Nov 19, 2009 | 1998 Nissan Maxima

1 Answer

1998 pontiac gtp ,


remove the right side wheel
seperate the ball joint
you may have to remove the stablizer bar link
remove the drive axle nut 32mm or 1 5/16
slide the front of the axle back through the hub bearing
then pop the axle out of the transmission
then install your new axle and reassemble

Jul 17, 2008 | 1999 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...