Question about 2005 Jeep Grand Cherokee

Open Question

05 jeep slap stick not working

Will go in drive ok but will not shift down or up i need to know how to fix this or how much it will cost to fix.

Posted by on

  • jameshuffine May 11, 2010

    Is it a standerd trasmission or automatic.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mecanica03
  • 881 Answers

SOURCE: sloppy shifting on 2007 jeep liberty

i think you go to dealer to reprogram the transm. by original programmer

Posted on Jul 05, 2009

  • 6 Answers

SOURCE: I have a 1987 jeep wrangler and it will not shift into 4 wheel dr

The front axle connects 4wd by vacuum. check the vacuum hoses that run to the actuator. Pay close attention to the vacuum hoses running underneath the battery as battery acid can eat thru those hose easily. Good Luck.

Posted on Jan 07, 2010

  • 4088 Answers

SOURCE: 1989 jeep wrangler wont shift gear and clutch gone loose

If the clutch system is hydraulic, check the clutch master cylinder for proper fluid level. If out or nearly so, look for signs of fluid leakage around the master cylinder, the hose down to the clutch slave cylinder, and the slave cylinder itself. If everything looks dry, fill the master cylinder with fresh fluid, bleed the air out of the system (like the brake system), and check that the clutch arm is moved by the clutch pedal properly. If all looks correct, try putting the transmission in gear with the engine running. Hope this gets you running!

Posted on Jan 10, 2010

  • 238 Answers

SOURCE: I have a 1989 jeep wrangler. yesterday, after the

Sounds like you are having a clutch problem. The sudden looseness in the clutch pedal indicates a problem with either the hydralic system, (slave or master or line) leaking or clutch pressure plate going out. Check your clutch fluid resevoir first, if low look for a leak under the vehicle, have a friend push the clutch and get underneath to find leak.

Posted on Jan 10, 2010

  • 99 Answers

SOURCE: I have an '05 Jeep

this is a bad shift control module it is part of the shifter it is about 700 in parts these are only available from a dealership get back with me if you want to try to change it your self it is hard to do.

Posted on Dec 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wont shift gears jeep


what jeep, and what year.
1946? willis jeep.
we cant guess what you have. no photos, no year.
no body class.
wont shift?
is it a stick shift or automatic
if auto, is the lever stuck?
or in drive car will not move.?
is stick shift, say so. and we work that end.
all cars are not the same,

Nov 09, 2016 | Jeep Cars & Trucks

2 Answers

Automatic transmission shifts down on its own


the kick down cable must have slack, at idle.
if not its bad. (end to end, something is wrong with it)
this cable is for passing gear.
you jam the throttle and the tranny then down shifts.
called, kickdown, detent and TV cable.
if the cable rusts it can in fact rust , pulled. and now in passing gear full time. or it can stick driving do to rust.
what i do is make sure the trans, end of cable the detent rod is not sticking, if that is ok, , get a new cable.

Mar 15, 2014 | 1997 Jeep Grand Cherokee

1 Answer

Why is the slap stick on my suv not working


I have an '04 Outlander and the manual slap stick stopped working. I also noticed the Drive light was not on when in auto drive. This is a common problem with this model and a relatively easy fix. Tools you will need are a small flat head and medium cross head scredriver, solder gun and electronic grade solder, small heat shrink tubing. Remove the entire center console - start at the rear by removing the 4 philips screws in the center arm rest compartment, remove the cover plate underneath the hand brake and the 2 side panels on either side at the front. Remove the shift knob (2 screws behind the small cover plate on the front of the knob - remove with small flat head screwdriver). Remove all remaining screws and the rear section, then slide the center section over the handbrake followed by the front section.

You will see a small switch on the shift lever with 3 wires (Black, Blue and Red). Most likely one or more have become detached, at this point it is best to unsolder any that are still attached because they will likely break in the near future! Remove any old solder and wire from the 3 contacts with the solder gun on the switch and tin each with fresh solder. Strip about 1/8" on each of the 3 wires and tin each with solder. Slide about 1/2-3/4" of the heat shrink tubing onto each wire. Solder the wires back to the swtich in this order:

Black - top
Blue - center
Red - bottom

Start at the top and work down, and after soldering each slide the heat shrink tubing over the solder joint and shrink by applying the solder gun - this will provide better mechanical support and help prevent future breakage.

Reassemble the center console in the reverse order of removal - make sure you have no screws left over!!

Good luck - hope this helps.

Oct 07, 2012 | Mitsubishi Outlander Cars & Trucks

1 Answer

2005 Altima SE is missing 3rd gear


I know this is an older post but I just replaced the solenoid in my 05 altima and the same thing with 3rd gear. I was wondering what you did to fix it?

Aug 15, 2012 | 2005 Nissan Altima 3.5 SE

1 Answer

Hello, I have 1992 jeep wrangler, i was feeling a slight sticking point half way up during the release of my clutch weeks ago and it seemed to go away. Yesterday my clutch pedal seemed to sit almost an...


Hey.This is just a long shot.The throwout bearing may be sticking.Its attached to the clutch fork and contacts the pressure plate.It slides along a shaft and the shaft may me sticking up,holding the bearing in the wrong spot.I have seen it happen.A VERY SMALL squirt of wd40 can fix it.You have to know where to put it.Not so much it gets on the clutch plate.Ask a friend or anyone that may know before you do it.This is your 1st option before you have to do any mechanical work on the car.It costs NOTHING.Check it before a workshop rips you off.Hope this helps you

Sep 21, 2010 | 1994 Jeep Wrangler

2 Answers

Will not move from 2nd gear help PLEASE?


Your transmission is in a "limp in" mode. There are 2 sensors that need replaced. Total cost should be less than $100. I had it happen to me on my 99 300m. The sensors limit the speed to about 25 mph and the RPM rev's high. Just get the sensors replaced.

Sep 18, 2009 | 1999 Chrysler 300M

1 Answer

2005 Jeep grand cherokee autoshift is not working.


This is not an auto shift or slap stick it is actually used to determine your top gear... its like putting your care in 1 or 2 gear

Jun 20, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Cant shift into first gear or reverse


You are likely correct...sounds like the synchro is shot or the shift fork is somewhat worn. Is fluid full?
As long as the clutch does not slip and is engaging and disengaging somewhere in the center to just below center of travel, it's OK.

Apr 22, 2009 | 1999 Jeep Wrangler

1 Answer

Inconsistant transmission problems on 2003 jeep gcl


Many times this is caused by either a sticking electronic shift solenoid in the transmission or the trans fluid and filter need to be replaced, has the trans been serviced, it should have been done at 60,000 miles.

Dec 01, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...