Question about 1997 Saturn SL

Open Question

I need to install my vent window on the back door of my car and the window does not have instructions with it.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 ford explorer rear window removal


Hi there:

  1. Remove the door trim panel and speaker if applicable.
  2. Remove the screw from the division bar. Remove the inside belt weatherstrip(s) if equipped.
  3. Remove the 2 vent window attaching screws from the front edge of the door.
  4. Lower the glass and pull the glass out of the run retainer near the vent window division bar, just enough to allow the removal of the vent window, if equipped.
  5. Push the front edge of the glass downward and remove the rear glass run retainer from the door.
  6. If equipped with retaining rivets, remove them carefully. Otherwise, remove the glass from the channel using Glass and Channel Removal Tool 2900. Remove the glass through the belt opening if possible.

To install:
  1. Install the glass spacer and retainer into the retention holes.
  2. Install the glass into the door, position on the bracket and align the retaining holes.
  3. Carefully install the retaining rivets or equivalent.
  4. Raise the glass to the full closed position.
  5. Install the rear glass run retainer and glass run. Install the inside belt weatherstrip(s).
  6. Check for smooth operation before installing the trim panel.



Hope this helps.

Feb 28, 2013 | 1998 Ford Explorer

1 Answer

Its a 2000 se passenger window trys to roll down but will not and back vent windows will not open


Sounds like bad master switch in the drivers door or the wiring in that door jamb. Try holding the control to move the vent window while moving the rubber containing the wiring to the door with the door open if something moves back there its a wire ready to break. if so pull the boot and check/repair the wire

Nov 16, 2010 | 2000 Dodge Grand Caravan

1 Answer

Need to know how to replace driver window in 1988 bronco. window has a side vent.


you will need to take off door panel and roll the window down. You should be able to look inside and see the tracks it rolls up and down on. disconnect from tracks and pull old window out the top of door, slide new window in and hook to tracks, should be very easy to install on such an older truck.

May 18, 2010 | 1988 Ford Bronco

1 Answer

I need to install a window in my vw polo. It is the back seat pasanger side window, i have already purchased it and have the inside panel off. My issue is fitting the window inplace without it smashing,...


We don't have Polo in the States but it would be the same design as a Golf or even a Jetta, even a Passat.
  1. Remove nuts from glass clamping jaws, press jaws apart, an access port would reveal both nuts at the same level
  2. Lower door glass into door, pull window channel (Window rubber gasket) out of door frame and remove center connector (metal channel strip that separates vent window. A screw on top and a hex head screw at bottom)
  3. Pull door glass upward, tilt toward front and lift out of window slot
  4. Install in the reverse order of removal
Note: Clamping jaw hex nuts torque spec.......10Nm (7ft-lb)

May 04, 2010 | 1998 Volkswagen Golf

1 Answer

We accidently had the door shut on my friends 95 fork truck, and the keys were still in ignition. We had to break the ventglass window, how do we replace that? window


1st. Remove door trim panel by removing the screw retaining the armrest section of the trim panel to the door inner panel and remove armrest.
2nd. Remove the screw retaining inside door handle and remove the handle.
3rd. On vehicles with manual operated window cranks remove the screws retaining the crank, then remove the crank and washer.
4.th On vehicles with power windows, remove the power window switch panel by inserting a thin blade screwdriver between the bezel abd the trim panel, at either side of the bezel. Then carefully pry the bezel from the trim panel and the housing assembly will snap out. Remove the retaining screws from the bottom side of the connector and remove the switch assembly from the connector.
5th Remove door lock control knob on models rquiped with.
6th On models with power door locks, remove the switch housing assembly from the panel by inserting thin blade screwdriver into the spring tab slot located at the top and bottom of the switch housing. Apply pressure and the assembly will pop out. Disconnect the housing from the wirring assembly connector by separating the lock fingers.
7th. If equipped with power outside rear view mirror, remove the switch housing bezel by removing the two retaining bezel nuts and the bezel.
8th. Remove the screw retaining division bar to inner door panel.
9th.Remove the screws retaining vent window assembly to the leading edge of the door.
10th. Lower the door glass to the bottom of its travel.
11th. Pull the glass run out of the upper run retainer next to the vent window division bar. Pull the glass run out just far enough to allow the vent window assembly to be removed.
12th Tilt the vent window and the division bar assembly toward rear of the door. Carefully guide the assembly up and out of the door.
13th. Remove the two upper pivot-to-vent frame screws.
14th. Remove the retaining nut and tension spring from the vent vindow lower oivot.
15. Separate the vent glass retainer and the pivot stops from the vent frame and weatherstripping assembly.
16th. Installation is reverse of the removal procedure. The pivot tension spring should be adjusted so the vent will remain open at higway speeds. Be sure the front door window spacer is in place when installing the vent window and division bar assembly.

I know it is hard to picture it but this is best I can explain with out picture.

Feb 23, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

How to install a window 2004 nissan 350z coupe?


Remove inner panel carefully. find 2 black circle stickers and raise glass to access 2 screws holding glass. Door vent does not need to be removed.

Jan 30, 2010 | 2004 Nissan 350Z

1 Answer

Replacing a rear vent window on a 98 Cavalier


do you mean the quarter light glass ,if so then have to remove the big glass first ,then the rear window runner /channel

Jan 08, 2010 | 1998 Chevrolet Cavalier

2 Answers

Need to replace a broken window on rear passenger 1999 jeep chero


This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Sep 09, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Installation instructions to replace drver mirror on 2006 Sebring


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Mar 28, 2009 | 2006 Chrysler Sebring

1 Answer

Vent window repair.


To replace the window seal, you first have to remove the vent window assembly from the door. After it is removed, the nut and spring on the bottom of the window has to be removed. Then remove the glass and frame from the vent assembly frame. Then gently remove the rubber off of the frame and install the new one after you replace the top vent bar seals. Reverse the window removal procedures to reinstall the glass and frame. The top vent bar seals requires a special tool to remove and replace the rivets you get with the replacement seal. You need to replace the top vent bar seal before reinstalling the new vent window rubber. When I replaced my top vent seals, it was fairly easy with my removal/installation tool.

Oct 03, 2008 | 1965 Ford Mustang

Not finding what you are looking for?
1997 Saturn SL Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...