Question about 2003 Hyundai Tiburon

Open Question

Rear hub assembly 2003 tiburon

Where can I find an online free manual to assist with replacing rear huib assembly on a 2003 hyundai tiburon , v6, antilock brakes?

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai Tiburon: Replacing plastic cover that encases everything.


Call around to your local auto wrecker/salvage yards, and check ebay before you go to a Hyundai dealer.

Apr 19, 2010 | 2003 Hyundai Tiburon

1 Answer

03 hyundai tiburon serpentine belt change


You can go to autozone.com and register for free for free online repair manual for your vehicle. Also google images have pics. There are also more manuals here:
http://manualspace.com/manual/search/89-toyota-celica-gt-repair-manual-online-pdf.htm

Feb 06, 2010 | 2003 Hyundai Tiburon

1 Answer

What does it take to replace the front wheel bearings on a 2003 Tiburon


the front wheel bearings on your car are not sold except as a front wheel hub assembly with the bearing pre-installed, they run about $100.00 each, to replace them requires no special tools, all u do is remove the wheel, the brake caliper and the brake rotor and the hub nut, then the hub just slides off, u will most likely need a very large socket for the hub retaining nut.

Jul 05, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of Purge Control Valve on 2003 Hyundai Tiburon GT


Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Jun 09, 2009 | 2003 Hyundai Tiburon

1 Answer

Location of the Purge Control Valve for 2003 Hyundai Tiburon


There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Jun 06, 2009 | 2003 Hyundai Tiburon

1 Answer

I want to change rear wheel hub for 2000 Hyundai Tiburon.


Easy. go to http://www.hmaservice.com/ and register. Shop manuals, trouble shooting, wiring diagrams, etc.

May 18, 2009 | 2003 Hyundai Tiburon

2 Answers

Change front wheel bearings


u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Mar 12, 2009 | 2003 Hyundai Tiburon

1 Answer

2003 Tiburon 6 spd clutch replacement now tranny won't respond


Possibility, you may have intalled the clutch disk backwards.... if so, the disk hub is torqued against the crankshaft hub preventing engagement of the clutch. 2003 TIBUORN DUAL MASS FLYWHEEL AND CLUTCH DISC ASSEMBLY INSTALLATION PROCEDURE DESCRIPTION: The 2003 MY 2.7L Tiburon vehicle equipped with the 6-speed manual transaxle employs a dual mass flywheel system. The 2003 Tiburon Shop Manual does not show the clutch disc assembly with the dual mass flywheel. This bulletin provides information about how to assemble these components. NOTE Although it is possible to assemble the clutch disc with either side facing the flywheel surface, only the assembly of these two parts shown in this bulletin is correct.
PARTS ASSEMBLY:
  1. Attach the dual mass flywheel to the engine crankshaft assembly.
  2. Identify the clutch disc flange side and the collar side as shown. 0240025a.gif
  3. Install the collar side of the clutch disc on the dual mass flywheel surface so that the flange side is facing the pressure plate side as shown. 0240025b.gif
  4. Attach the pressure plate to the dual mass flywheel and complete assembly of the remaining components per the Shop Manual procedures. 0240025c.gif

Dec 14, 2008 | 2004 Hyundai Tiburon

1 Answer

2003 Hyundai Tiburon Gt rear brakes


hi not conversant with the tiberon in uk but will try to help ? if you remove the rear wheel then look at the brake disc (rotor) most hyundai rear discs on uk models are secured to the rear hub by 2x screws posidrive or tork heads ? if this is so on yours then no problem you will have to remove the caliper first from the carrier 2xbolts h/brake off then undo 2xbolts securing caliper carrier tosuspension stub assy your disc /s are most probably vented discs? or may be standard discs? remove the screws then you may have to hit disc from behind with hammer to jolt free as they are sometimes rusted on due to high temps and rain ideal conditions to create rust as you prob know? re assemble is reverse hope this helps ?

Oct 20, 2008 | 2003 Hyundai Tiburon

3 Answers

1998 tiburon 5 speed manuaL transmission


hey
try to use quaker state synthetic bleed multi vehicle atf

Jul 06, 2008 | Hyundai Motor 1999 Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...