Question about 1992 Ford F150 SuperCab

1 Answer

RV c6 transmisson stuck in park

While installing headers in my 1989 John deere chassie rv I had to bend the shift rod a little. While I had the rod disconnect I was able to shift through the gears at the tranny. When I connected the rod it would not shift, and will not move out of park even with the shift rod disconnedted.

Is it possiable that something came loose inside the transmission?
If so can it be fixed without removint the tranny?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,537 Answers

I think you may be fighting the shift interlock with the brake pedal. Remember, to shift out of Park you need to step on the brake.
You might need someone to hold down the brake pedal while you try to realign the rod from underneath.

Posted on Sep 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset pcm 1995 gmc 6.5 1ton chassie on rv


ONLY a guess but sounds like your battery is dead .

Oct 04, 2015 | GMC Cars & Trucks

1 Answer

93 Georgie boy Cruisemaster motorhom 93 Georgie boy Cruisemaster motorhome stuck in park i 93 Georgie boy Cruisemaster motorhome stuck in park any ideas on how to fix


As with most cars and trucks, if the shifter won't move out of park, one possible cause is a faulty brake switch or shift lock solenoid.
If the RV is on flat ground and the park pawl is not under heavy load, you may be able to shift out of park by unlocking the steering wheel but not turning the key to the on position. Make sure the parking brake is set before you try it.

Sep 18, 2015 | Cars & Trucks

1 Answer

Is there a wiring diagram for georgie boy; cruise master 11 RV?


follow link for the georgie boy forum , best place to ask i'd have thought
Georgie Boy Owners Club

Jun 07, 2014 | 2002 Chevrolet TrailBlazer

1 Answer

HAVE A 1989 FORD F-150 WITH AUTO TRANS THAT YOU CAN'T SHIFT OUT OF THE "PARK" POSITION AT THE STEERING COLUMN. THE TRANY CAN BE SHIFTED AT THE TRANS WHEN LINKAGE IS DICONNECTED.I THINK THE...


What trans? AOD? This is 1992 F Series, all I have.

Shift Controls, Automatic Transmission The transmission shift control linkage or cable transfers the transmission operating mode from the selector lever to the transmission. The indicated transmission position on the steering column is transferred to a shift lever on the bottom of the steering column. On vehicles equipped with cable-operated shift systems, the indicated position of the transmission selector lever is transferred to the transmission through the shift cane, then to the cable, and down to the transmission manual shift lever at the transmission. On vehicles equipped with shift rod assemblies, the rod transfers the indicated transmission selector level position through a bell crank assembly to a control rod. The control rod transfers the indicated position to the transmission assembly.
----------------------------------------------
Automatic Transmission Manual Linkage Adjustments
  1. With the engine stopped and the parking brake applied, place the transmission selector lever at the steering column in the D (DRIVE position) for C6 applications and in the (D) (OVERDRIVE position) for AOD and E4OD applications, and hold against the D or (D) stop by applying a three-pound force to the selector lever knob.
  1. Loosen the shift rod adjusting nut at point A. Refer to the following illustrations.
  1. Shift the manual lever at the transmission into the (D) (overdrive) position for E4OD, by moving the lever all the way rearward, then forward two detents.
  1. With the selector lever and transmission manual lever in the(D) position, tighten the nut at point A to 17-24 Nm (12-18 ft-lb) torque. Use care to prevent motion between the stud and rod.
  1. Remove the three-pound force from the steering column selector lever knob.
  1. Operate the shift lever in all positions to make certain that the manual lever at the transmission is in full detent in all gear ranges. Re-adjust the linkage if required.
  1. On F-Super Duty Chassis Cab and Motorhome and Commercial Chassis recheck for correct operation of the automatic transmission selector indicator (PRN(D)21). Refer to Section 11-04A, Steering Column, Shift Rod Within Tube. ani_caut.gif CAUTION: Under no circumstances will it be permissible to adjust linkage in any position other than the(D) position for E4OD applications.
---------------------
Automatic Transmission Shift Cable Adjustment
  1. From inside the vehicle, place the column shift select lever in the DRIVE position (C6) of the OVERDRIVE (AOD and E4OD). Hang a three-pound weight on the selector lever.
  1. Raise vehicle on a hoist.
  1. Remove the shift cable from the transmission lever ball stud.
  1. Pull down the lock tab on the shift cable body.
  1. Position the transmission shift lever in the DRIVE position (C6) or the OVERDRIVE position (AOD and E4OD). This is three detents from the front-most lever position with the first position counting as one.
  1. Connect the cable end fitting to the transmission lever ball stud.
  1. Push up on the lock tab to lock the cable in the correctly adjusted position.
  1. Lower vehicle down from hoist and remove the three-pound weight from the column shift select lever.
  1. After making the adjustment, check for park engagement. Check the transmission control lever in all detent positions with the engine running to make sure correct detent/transmission actions. Readjust if necessary.

Jun 21, 2011 | Ford F-150 Cars & Trucks

1 Answer

There is no parking brake, and "park" does not hold. it is a 1990 cruise air lll on a john deere chassis with a ford 460 engine.


The parking brake is activated by the shift lever. There is no parking paw in the transmission on these John Deere Chassis motor homes. The parking brake is the type that works a brake on the drive shaft. I ran into the same problem and just put a line lock on the brake line.

Sep 01, 2010 | Ford E-350 Super Duty Cars & Trucks

1 Answer

I replaced both batteries in this RV. An


Can you give me more details on the RV, such as chassis make ( Ford I'm guessing) year, and engine, and what make and model of the RV itself. The reason I ask for RV make as well is because some manufacturers of RV's use different battery isolators, set-ups etc., in their units.

Dec 04, 2009 | 1989 Ford Econoline

2 Answers

Transmission 1898 F-250


Re-check all cable, shift rods, and safety neutral switch for proper adjustment.

Dec 13, 2008 | 1997 Ford F250 SuperCab

Not finding what you are looking for?
1992 Ford F150 SuperCab Logo

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...