Question about 1999 Jeep Grand Cherokee

2 Answers

How do you reconnect cables on rear passenger window regulator motor? The cable that pulls the window up is disconnected from window regulator. Where does this reconnect too?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 71 Answers

The cable you are describing is the window regulator cable. They generally fray and come apart, thus the reason the cable comes out. The only fix I am sorry to say is to replace the regulator assembly.
Wish I had a nicer answer

Posted on Sep 05, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 323 Answers

You need to replace the regulator assembly, there are no repair parts available for it.

Posted on Sep 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I manually put up the rear passenger window of my 2002 Chevy Malibu? I just need it up until tomorrow when I can get the parts to fix my motor and regulator?


Only thing you can do is unbolt the window from the regulator and stick a board or something inside the door to hold it up. No way to just pull it up, the cable on the regulator most likely broke and wrapped up in the motor.

Aug 17, 2011 | 1999 Chevrolet Malibu

1 Answer

Passenger power window will not go up


Hello, this either the window motor or the window regulator has came apart. the most common problem is the window regulator. the window regulator is cable driven. the cables will break causing the window not to operate. you will need to pull of the door panel and makes some visual inpections

Jul 08, 2011 | 2001 Chevrolet Silverado 1500

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

2 Answers

Rear window will not roll up. i removed the door panel and there was a cable that had been disconnected from the motor, my problem is that i cannot get the rear window to disconnect from the plastic lever...


There is a nylon peg that holds the window to the regulator.You need to use a 1/8 in.pin punch to remove the peg.But you have to get the window up far enough where the peg lines up with the hole in the regulator.You will have to replace the regulator.If you put the cable back on it will just fall back off.Hope this helps.Good luck.

Dec 19, 2009 | 2005 Chevrolet Malibu

1 Answer

I need instructions on how to replace power window motor for the front driver side window of a 2002 Grand Cherokee


Power Window Motor: Service and Repair
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
INSTALLATION
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

Oct 30, 2009 | 2002 Jeep Grand Cherokee

2 Answers

I have a 2001 buick le sabre. The rear widow does


That is the problem....however the cable spun off the spool and you need to buy the power window assy. On line it was a good fair price (about $35-50) it has 3 studs that holds it to the inside door and 2 bolts at the window that secures the assy to the window. All work can be completed in 30 mins..

Sep 09, 2009 | 2001 Buick LeSabre

1 Answer

Need to find a way to take off the drivers side window motor


Motor
  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door.
To install:
  1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  2. Connect the power window motor wiring.
  3. Connect the negative battery cable.
  4. Check window operation.
  5. Install the watershield and door trim panel.

Door Panel
  1. Disconnect the negative battery cable.
  2. Snap out the two door pull strap retaining screw covers. Remove the screws.

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


  1. Remove the two screws on the front and rear side of the front door trim panel.
  2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


  1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
  2. Disconnect the driver seat regulator control processor switch if equipped.
  3. Twist out the interior lamp wire assembly.
To install:
  1. Ensure that the plastic watershield is secured to the door .
  2. Position the front door trim panel to the door. Connect the interior lamp wiring.
  3. Align door lock side to its mating slide on the sheet metal.
  4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
  5. Connect the driver seat regulator control processor, if equipped.
  6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
  7. Install the two retaining screws and pull strap covers.
  8. Connect the negative battery cable.
053777a.gif

Aug 27, 2009 | 2000 Lincoln Town Car

1 Answer

I have a 1993 Ford Tempo and am having problems removing the motor from the door. I already have the door panel removed and the power disconnected from the motor.


remove the door panel and check to make sure the linkage to the lock assembly is still attached. I can't give an estimate because I don't know what is wrong at this point

are the locks manual or electric?i have seen most electric locks freeze up because of rust/.corrosion.the rubber accordian seal fails and moisture does it's job.there is no lubrication on the mechanism.it's basically a push pull magnet tube with a spiral grooved actuator rod.this is to assure no accidental vibration/jar induced movement.also means very difficult to budge when corroded.i have gotten a few to move by grabbing lock post with pliers and pulling hard.good luck!



Rear Door Window Regulator and Motor
Removal and Installation
Remove the rear door trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
Remove the door mounted speaker.
Remove the watershield.
NOTE:The glass must be lowered for this step.

NOTE:Some vehicles may use rivets to attach the glass to the regulator.

Remove the bolt that attaches the glass to the regulator.
Raise and support the rear door window glass to the full up position.

NOTE:Do not detach the door handle from the latch cable during this step.

Remove the rear inside door handle.
Remove the screw.
Disengage the inside door handle from the door.
If equipped, disconnect the power door lock rod from the back of the inside door handle.

Gain access to the power window motor electrical connector located in the front of the door.
Fig. 90: Identifying Power Window Motor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the power window motor electrical connector.
Press down on the connector tab.
Pull the connector upward and remove through the speaker opening in the door.
Disconnect the rear door window regulator and motor assembly from the door.
Remove the nuts.
Remove the screws.
Fig. 92: Disconnecting Rear Door Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_2.jpg
Remove the window regulator and motor assembly from the door.
Fig. 93: Removing Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_3.jpg

To install, reverse the removal procedure.

Jul 01, 2009 | Ford Tempo Cars & Trucks

1 Answer

Replacing rear passenger window


I ended up removing the regulator, replacing the window in its track and ordering a replacement regulator.
the information provided by FixYa was helpful in getting the window back in place but the main issue was 'restringing the cables' on the regulator - apparently difficult if not impossible to do, therefore the necessity to order the new part.

Mar 21, 2009 | 2004 Pontiac Grand Prix

1 Answer

Cables have become disconnected from power window regulator motor


you have too take the winwow guide rails out put it all together and put it back in in one peice

Mar 21, 2009 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...