Question about 2001 Chevrolet Malibu

Open Question

Car trys to start but will not stay running

Lights on dash
no security light on

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

5.3 wont stay running


Check your security light on the dash and see if it stays on or blinks with the key in on position. If so google how to reset the security.

Dec 02, 2013 | 1999 Chevrolet Tahoe

1 Answer

Light Security Stays on after code learned


that\'s the thing about new cars. they suck. all this electrical this, electrical that, you are sheit out of luck bud. junk it and buy something older that most people know how to fix.

Oct 24, 2013 | Cars & Trucks

1 Answer

Changed battery trimals and car starts but wont keep running do to secuity light


Best,Genuine and Simple Online business which Really Makes you a Millionaire ! visit :- http://bit.ly/xM9lTH

Feb 20, 2012 | 1993 Jeep Grand Cherokee

2 Answers

Van will start but not stay running 97 chevy venture


If it starts for 5 seconds out less, and you notice a security light on the dash, go to this link for answers. Gm are notorious for failing antitheft systems http://vatspasslockpasskeysecurityhelp.yolasite.com/

Oct 02, 2011 | 1997 Chevrolet Venture

1 Answer

Starts but wont stay running...idels for about 5 sec


Try to start the car. After it stalls, keep the key forward and look along the dash panel for a light that says "security" or a light that looks like a car with a padlock thru it. If you see this light, go to this link http://vatspasslockpasskeysecurityhelp.yolasite.com/

Aug 29, 2011 | 2000 Pontiac Grand Prix

2 Answers

1991 park avenue will start but shuts down it will not stay running. replaced fuel filter still will not stay running


Check to see if the security light illuminates on the dash when it is not starting. If the key is forward and the security light is on, you have a problem with your vats security system. If this is the case, check out this link http://newrockies.com/passkey.

Mar 29, 2011 | 1991 Buick Park Avenue

3 Answers

Car started an hour ago now wont turn over security light in dash came on and stays on


if the security light is on then it is the VATS system. the ignition switch is fine still.

Aug 15, 2010 | 1995 Chevrolet Camaro

2 Answers

Head and tail lights won't turn off when key is removed.


wires must have been trapped,shorted when engine was removed, check loom for damage

Jul 05, 2010 | 1997 Subaru Legacy

1 Answer

Battery is charged. Went to start car at the end of the day, and there is a mechanical clicking sound (all dash indicators light) but the starter motor won't engage, and car won't turnover. Bad...


Do this to check if it's a bad battery, turn head light's on and try to start it, if head light go to dim or off, bad battery not holding a charge, if light stay on ok, then this will take two people tap on the starter kinda hard with a hammer or something you can reach it with while some one hold's to key to start, if it start's bad starter or trys to turn engine replace it.

Jun 29, 2010 | 2001 Mercury Sable

1 Answer

How do I program my key for my 2006 Chevy Impala?


Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

May 20, 2009 | 2006 Chevrolet Impala

Not finding what you are looking for?
2001 Chevrolet Malibu Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...