Question about 1996 Lincoln Town Car

1 Answer

I have a water leak inder the intake manifold how do you replace that line?

Posted by on

  • Darell Gholston
    Darell Gholston Sep 09, 2009

    You have to remove the intake to replace that one. Or if you have the patience to remove the alternator and if possible remove the clamp from the water line just behind the water pump. You can then snake another line from the heater core down through the back of the engine, after removing the metal pipe and replacing the hose there behind the water pump, like I said if you have the patience. I wish i had tried this before taking my intake off, its easier said than do though.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 532 Answers

You have to pull off the intake,its a steel line with a short piece of rubber line attached to it on the front side of the engine,you can almost see it just behind the alternator.

Posted on Sep 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 ford taurus,lopes when first started,when cold.


intake manifoold leak check all vacuum lines replace all vacuum lines if look cracked ,spark plugs could be fouled out by leaking fuel injectors, clean fuel injectors,replace fuel filter,replace air filter,replace spark plugs and wires,do tune up see if it helps if not.could have leaking intake manifold gasket or leaking egr valve,use engine vacuum gauge check engine vacuum for intake manifold gasket leaks.

Sep 23, 2012 | Ford Cars & Trucks

Tip

Intake Manifold gasket replacement and/or leaking= Ford


Intake Manifold gasket~

Replacing intake manifold gasket:
Replacing the intake manifold gasket, I used the tube kind, it's a make it youself for about $6 (it's blue and the consistancy of toothpaste) follow directions carefully! You can get a tube at Autozone or any car parts store. Has been working great. Just ask the cashier for the make it yourself kind of intake manifold gasket. Sorry, I don't remember the name of it, it's been that long...lol...

As for the Intake Manifold leaking coolant....It could, but shouldn't. One of the largest problems I've seen for coolant to leak out the Intake Manifold has been due to pressure in the system somewhere... Check the classic area:
Water pump- look for either water seapage and/or coolant. You'll know if it is because you will see real water either coming out of the water pump leak hole or under the thermostat. Most of the time coolant will pool where your heater hose runs in the intake manifold.

Mentioning heater hose. Check for leaks, holes, and/or cracked heater hoses. In-addition to the water pump, heater hoses...Check the transmission system, exhaust system, fuel system, radiator system, A/C system, secondary fan (located above the water pump housing), and thermostat.Also, check all electrical connections....Hummm....This is almost the entire workings of the vehicle.

NOTE: "It seems to be an infinity kinda thing... Once one thing starts to fail and is ignored, you are bound to be fixing a chain of event failures. Therefore, Do not ignore even the smallest problem or you'll be bound for life in repairs...."

on Jun 25, 2010 | Ford Expedition Cars & Trucks

1 Answer

What does the intake have to do with a car overheating?


The intake manifold has a water passage that takes water from one side of the engine and moves it to the other side in a V6 engine. Your engine has a plastic tube that does this job. That tube can leak which leads to water and pressure loss and that leads to overheating. Ask him if he is referring to the water crossover tube in the intake manifold. If that is what he is referring to the that is a 6 hour replacement job. You should have the water pump and belts replaced at the same time along with upper and lower radiator hoses. That price is a bit high but not that out of line.

Aug 03, 2012 | 1998 Oldsmobile Bravada

1 Answer

Surging idle 2003 nissan altima s


I think you have an air leak, a vacuum line loose, or possible intake manifold gasket leaking, maybe your big air intake hose is leaking. spray carb cleaner or soapy water around mating surface of intake and on vacuum lines and connections. If idle changes, there is your leak. good luck.

Oct 27, 2011 | 2005 Nissan Altima

1 Answer

1999 Alero : Fuel leaking at a fitting where fuel line goes under intake manifold. Does manifold have to be removed to remove or tighten this fitting?


IF FUEL LINE FITTING LEAKING UNDER INTAKE YOU HAVE TO REMOVE TOP INTAKE MANIFOLD TO REPLACE FUEL LINE FITTING O RING.

Sep 15, 2011 | 1999 Oldsmobile Alero

2 Answers

Car has uncontrollable idle and wants to shut off and reads no codes


check for vacuum leaks on intake manifolds vacuum lines intake etc.
I have used a spray bottle of soapy water on intake manifold to find a leaky manifold.

Jul 27, 2011 | 2005 Ford Focus

2 Answers

Need to replace the intake manifold


3.8L Engine (most common) Upper Intake Manifold To Remove:
  1. Drain the cooling system.
  2. Remove or disconnect the following:
    • Negative battery cable.
    • Fuel injector sight shield.
    • Air cleaner intake duct.
    • Right spark plug wires from the ignition control module and reposition.
  3. Relieve the fuel pressure.
  4. Remove or disconnect the following:
    • Fuel rail assembly.
    • Brake booster hose from the vacuum source manifold in the upper intake manifold.
    • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
    • Throttle body support bracket upper bolt.
  5. Disconnect the electrical connectors from the following:
    • EVAP purge solenoid
    • Throttle Position (T/P) sensor
    • Idle Air Control (IAC) valve
    • Manifold Absolute Pressure (MAP) sensor
    • Mass Air Flow (MAF) sensor
    • EVAP purge solenoid vacuum line from the throttle body.
    • Accelerator and the cruise control cables with the bracket from the throttle body.
  6. Remove or disconnect the following:
    • Upper intake manifold bolts and stud.
    • Clean the upper intake manifold bolt threads.
  7. Remove or disconnect the following:
    • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
    • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
  8. If the upper intake manifold is being replaced, remove the following:
    • Throttle body assembly.
    • Manifold Absolute Pressure (MAP) sensor.
    • Positive Crankcase Ventilation (PCV) valve.
    • Vacuum source manifold.
Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

To Install:
  1. If the manifold was replaced, install or connect the following:
    • Vacuum source manifold.
    • Positive Crankcase Ventilation (PCV) valve.
    • Manifold Absolute Pressure (MAP) sensor.
    • Throttle body assembly.
    • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
  2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
  3. Install or connect the following:
    • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
    • Accelerator and the cruise control cables with the bracket to the throttle body.
    • EVAP purge solenoid vacuum line to the throttle body.
  4. Connect the electrical connectors to the following:
    • Mass Air Flow (MAF) sensor
    • Manifold Absolute Pressure (MAP) sensor
    • Idle Air Control (IAC) valve
    • Throttle Position (T/P) sensor
    • EVAP purge solenoid
  5. Install or connect the following:
    • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
    • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
    • Brake booster hose to the vacuum source manifold.
    • Fuel rail assembly.
    • Right spark plug wires.
    • Air cleaner intake duct.
    • Fuel injector sight shield.
  6. Connect the negative battery cable.
  7. Fill the cooling system.
  8. Inspect for fluid or vacuum leaks.
Lower Intake Manifold (W/O Supercharger) To Remove:
  1. Remove or disconnect the following:
    • Upper intake manifold.
    • Generator brace.
    • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
    • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
    • Radiator inlet hose from the water outlet housing.
    • ECT sensor electrical connector.
    • Right upper engine mount strut bracket.
    • Generator brace bracket bolts.
    • Generator brace bracket.
    • Lower intake manifold bolts.
    • Lower intake manifold.
    • Lower intake manifold seals.
    • Lower intake manifold gaskets.
  2. If replacing the lower intake manifold, Remove or disconnect:
    • Water outlet housing bolt and stud
    • Water outlet housing
    • Gasket and the thermostat.
    • ECT sensor.
  3. Inspect the flatness of inlet flanges.
  4. Clean the intake manifold mating surfaces.
  5. Clean the intake manifold bolts and bolt holes of adhesive compound.
To Install:
  1. If removed, install the ECT sensor.
    • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
  2. If removed, install the thermostat, the gasket, and the water outlet housing.
  3. If removed, install the water outlet housing bolt and the stud.
    • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
  4. Install or connect the following:
    • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
    • Lower intake manifold seals.
    • Lower intake manifold.
    • Lower intake manifold bolts.
    NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
  5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

  6. Install or connect the following:
    • Generator brace bracket.
    • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
    • Right upper engine mount strut bracket.
    • ECT sensor electrical connector.
    • Radiator inlet hose to the water outlet housing.
    • EGR outlet pipe to the lower intake manifold.
    • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
    • Drive belt tensioner.
    • Generator brace.
    • Upper intake manifold.
  7. Inspect for leaks.
Lower Intake Manifold (W/ Supercharger) To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the supercharger.
  4. Remove the thermostat housing.
  5. Remove the EGR pipe at the intake manifold.
  6. Disconnect the electrical connection at the temperature sensor.
  7. Remove the intake manifold and gaskets.
NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
To Install:
  1. Clean the gasket sealing surfaces.
  2. Install the intake manifold gaskets.
  3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
  4. Install the electrical connector to the temperature sensor.
  5. Install the EGR pipe to the intake manifold.
  6. Install the thermostat housing.
  7. Install the supercharger.
  8. Fill the cooling system.
  9. Connect the negative battery cable.

Aug 05, 2010 | 1997 Pontiac Grand Prix

2 Answers

Motor races to 2500rpm when idling and stays there


You have a vaccum leak. Check all vaccum hoses and connections for hissing or leaks.

Jan 18, 2010 | 1991 Ford F150

2 Answers

My 1999 chevy tahoe is leaking antifreeze. I


it could but- check passenger side front where heater core line go into manifold right behind alternator the hose line is connected by a press clip into an alloy fitting this fitting gets eaten away by anti freeze and hose angle pulls back on fitting the part is $18 at dealer and is screwed into manifold use caution if ur r going to replace at very edge of aluminum manifold---and check ur water pump bolts the 2 longer ones should have a lock sealant on them they bolt in thru a water jacket

Oct 24, 2009 | Chevrolet Tahoe Cars & Trucks

3 Answers

Water leaking from intake manifold


the chev are fames for intake manifold seeping. it will have to be replaced soon good luck

Mar 24, 2009 | Chevrolet 3500 Cars & Trucks

Not finding what you are looking for?
1996 Lincoln Town Car Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...