Question about 2000 Chevrolet Corvette

1 Answer

I need ti install a air pump on a 2000 corvette. Do you have a break down of what needs to be removed to get to the part

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 103 Answers

  1. Raise the vehicle.
  2. Remove the left hand side lower close-out panel.
  3. Remove the hoses from the AIR pump.
  4. Disconnect the electrical connector from the AIR pump.
  5. Remove the AIR pump mounting bolts from the bracket.
  6. Remove the AIR pump.
I need ti install a air pump on a 2000 corvette. - 9ba648f.gif

Posted on Sep 05, 2009

  • longbow243
    longbow243 Sep 05, 2009


    1. Raise the vehicle.
    2. Remove the left hand side lower close-out panel.

    3. Remove the hoses from the AIR pump.
    4. Disconnect the electrical connector from the AIR pump.
    5. Remove the AIR pump mounting bolts from the bracket.
    6. Remove the AIR pump.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram for the serpentine belt


dak408_39.gif

  1. Disconnect battery ground cable.
  2. Remove air intake duct from throttle body extension.
  3. Using a 1/2 inch ratchet, retract serpentine drive belt tensioner.
  4. Lift belt rearward, off water pump pulley, then remove belt from vehicle.
  5. Reverse procedure to install. Refer to Fig. 29 for serpentine belt routing.

Nov 19, 2010 | 1995 Chevrolet Corvette

1 Answer

1965 corvette fuel pump breather


It is a diaphram pump with a rubber diaphram. The rubber has more than likely dry rotted letting the gas go through it. When you take it off, there is a "lifter/pushrod?" that go's from the camshaft to the pump. And it will slide down, but there is a cover that holds it in. So it shouldnt fall all way out. When you install the pump pick the shaft up and make sure the fuel pump arm slides under it before putting it in place. Also make sure and lube the arm and lifter real good with duralube or another soft grease or at least lots of oil.
Start and run your car at least once a month and that will keep most of the parts from dryrotting as bad. Engines are made for running, not sitting.

I hope this helps.

Jul 26, 2010 | 1965 Chevrolet Corvette

1 Answer

How do i replace front drivers side brake caliper?


Jack the van up, remove the tire. Then you will see the caliper. There will be 2 bolts that hold it on to the rotor. Remove the bolts and pry it off with a screw driver or what ever works. Then disconnect the break line from the caliper. After you get the new one use a c-clamp to press the piston down into the caliper and install the brake pads. Bolt the caliper back into place and install the line. Loosen up the bleed valve on the caliper 1/2 turn and have someone pump the breaks until no air bubbles come out. Once you have a smooth stream of brake fluid coming out the valve have that person pump once more and hold the pedal all the way to the floor. Then tighten the valve.

Dec 29, 2009 | 2000 Dodge Caravan

2 Answers

Fuel tank sending unit needs replacing. The


the sending unit is in the tank. jack it up make sure fuels low disconnect lines and filler hose and wireing to pump drop straps lower tank.undo bolt to tank top unlock locking ring.take out sending unit and pump replace and reverse.involved but not that complicated unless your exhaust is in the way.hope that helps

Nov 25, 2009 | 1998 Chevrolet Corvette

2 Answers

2000 corvette convertible top rear window came


This is a common problem with many cars. It is delamination. If the window is loose in spots, it can often be repaired with urethane adhesive like glass shops use for windshields. If the glass is more than 30% delaminated, chances of fixing it are slim. With the glass all the way out, you need a new top. Karl at topgunwon.com

Oct 15, 2009 | 2000 Chevrolet Corvette

2 Answers

Where is the frost plug installed on a 2000 plymouth neon?


there are several.4-6 or more?? if the coolant is rusty, plan on doing all of them or sell the car. BIG $$$$...If you have not kept up with the coolant service,you will have much bigger problems later on. how many miles? at 90k miles replace the timing belt, tensioner and water pump, use factory chrysler parts only. if you dont and the belt breaks, or water pump siezes, the engine will be trashed.

Oct 02, 2009 | 2000 Dodge Neon

1 Answer

INSTRUCTIONS TO INSTALL FUEL PUMP ON 1989 CORVETTE


REMOVAL
  1. Relieve fuel system pressure.
  2. Disconnect battery ground cable.
  3. Remove fuel filler door.
  4. Remove fuel cap.
  5. Remove fuel tank filler neck housing and disconnect drain hose.
  6. Remove screws attaching fuel meter/fuel pump to tank.
  7. Disconnect fuel lines, fuel vapor line and electrical connector.
  8. Remove fuel meter/fuel pump and gasket.
  9. Replace fuel pump.
INSTALLATION
  1. Reverse procedure to install.

Jul 27, 2009 | 1989 Chevrolet Corvette

2 Answers

1985 corvette wont start


NEVER use either!! EVER! It burns very dry and can destroy a gas engine! Just give it a bit of gas down the intake.But keep the can away after each try! Far away! Not sure how you are getting 32v?? That can't be volts! Silly question, but is there fuel in the tank?? Have seen this before! It would be great to learn how this all started?? [or should i say stopped] lol Check the fuel line for a pin hole. It sounds like it is sucking air. Really need a bit more info. OK Frankster016

Oct 23, 2008 | 1985 Chevrolet Corvette

Not finding what you are looking for?
2000 Chevrolet Corvette Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...