Question about 1990 Chevrolet K2500

1 Answer

Were is thefuel pump located on a 1989 chevy 1/2 ton 2 wheel drive truck

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 285 Answers

This vehicle should be throttle body injected so the pump should be in the gas tank

Posted on Sep 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can anyone tell me if my F150 1987 is half ton or 3/4 ?


It is real simple. If it is an F-150 it is a half ton. If it was a 3/4 ton, it would be an F-250.

Dec 15, 2011 | 1989 Ford F 150

1 Answer

4 wheeldrive dose not engage on my 1989 1/2 ton chevy,i have changed front actuator and the switch on top of the transfer and neither one made a diffrence


Check the wiring, look for abrasions where wiring meets the frame, it may take a bit of searching to locate the problem. The wire doesn't necessarily need to be broken to not work, just shorted.

Dec 27, 2010 | 1989 Chevrolet C1500

1 Answer

1986 chevy pu 1/2 ton.2 wheel drive 4.3 litre v-6. My Truck sometimes starts,sometimes runs sometimes just turns over but won't start..I have replaced cap,wires.plugs,rotor,coil,battery and ignition...


Check your fuel pressure. This will tell you if you are getting enough fuel. If you are not getting the proper pressure either your fuel filter is clogged or your fuel pump is failing and needs to be replaced.

Sep 23, 2010 | 1986 Chevrolet Chevy

2 Answers

I need a service manual with wiring diagrams for a 1989 ford f150 1/2 ton 2 wheel drive 5.0L


http://cgi.ebay.com/ebaymotors/1989-89-Ford-F150-Truck-Repair-Manual-NEW-_W0QQcmdZViewItemQQhashZitem3a5e4465edQQitemZ250689644013QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories
Copy and paste that in your browser. Or go to ebay and type in 1989 ford f-150 repair manual. Or go to Autozone and sometimes they have it.

Sep 04, 2010 | 1989 Ford F 150

1 Answer

What motor came stock in a 1989 chevrolet


The eighth digit in the VIN number on the trucks dash (view from outside the truck on the drivers side) is the engine code. I believe M is a 350 and P is a 305.

May 27, 2010 | 1989 Chevrolet Suburban

2 Answers

Bleed brakes on 96 chevy 1/2 ton


YOUR TRUCK HAS KELSEY HAYES FOUR WHEEL DRIVE ANTI LOCK BRAKES EBC 310. YOU CAN BLEED BRAKES MANUAL STARTING AT - RR- LR RF- LF. THIS IS BLEEDING SEQUENCE.BUT YOU NEED A TECH 1 OR 2 SCANNER BECAUSE IF YOU REPLACED THE BPVM OR BRAKE PRESSURE MODULATOR VALVE.BECAUSE AIR TRAPPED IN VALVE ASSEMBLY.THE TECH 1 OR 2 SCANNER YOU HAVE PUT IN THE FUNCTIONAL TEST BLEED AIR OUT OF VALVE ASSEMBLY.THEN YOU CAN BLEED BRAKES MANUAL.

Mar 27, 2010 | 1996 Chevrolet K1500

1 Answer

1989 Chevy 1 ton wont start


It is likely the electronic ignition control module. When they go, they just go bad and usually when you are driving.

If it was a smaller vehicle it could also be a timing belt but your's has a heavy duty valve train so no worries there.

Mar 17, 2010 | 1989 Chevrolet C/K 3500

1 Answer

Truck will not go into 4 wheel drive


it sound like it is going in to 4low rang but it may only be low 2wheel power brake it a little on dirt if the tires sin in the rear it was only low ranged 2 wheel u can get this by putting it in 4low and unlocking the hubs it may be a hub prob as it is common

Dec 06, 2009 | 1989 Chevrolet K1500

1 Answer

89 Chevy 1/2 ton cruise control turned truck off


1989 20yrs old ,well it must have an ignition module ,but as i have never seen a truck like this i couldnt tell you the location ,its either by the coil or inside the distributor ,could evan be screwed to the outside of distributor .Iam sure this is your problem

Feb 19, 2009 | 1989 Chevrolet K1500

1 Answer

Trying to put a tranny (4L60E) from a 1995 chevy suburban 1/2 ton, 2 wheel drive into a 1993 chevy 1/2 ton 4x4, but the end piece is different and not able to hook up transferr case ?


If the overall length of the tailshafts are the same, If I remember correctly, you can just swap the tailshaft housings.In some cases though, the output shaft needs to be swapped as well. Check with any transmission shop and they can tell you for sure!

Dec 29, 2008 | 1995 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...