Question about Oldsmobile Delta 88

Open Question

Need to replace electric window device. I have the part and looking for step by step instrcutions.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 buick lacrosse 3.8LV6 .. All power windows dont work and radio wont turn on ..what can this be



You would need to test the electrical circuit to find out what this could be . Videos on youtube for basic electrical trouble shooting !
2

Are all the power windows inoperative?
YES - Go to Step 3
NO - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
3

    Disconnect the driver window switch C2 harness connector.
  1. Turn ON the ignition, with the engine OFF.
  2. Probe the power window switch voltage supply circuit of the harness connector with a test lamp that is connected to ground.
Does the test lamp illuminate?
Yes - Go to Step 4
NO - Go to Step 5
Connect the test lamp between the power window switch voltage supply circuit and the ground circuit of the harness connector.
Does the test lamp illuminate?
Go to Step 6
Go to Step 8

5

Test for an open or a short to ground in the power window switch voltage supply circuits of the driver window and front passenger window switches. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

6
Test the power window master switch lockout signal circuit for a short to ground. Refer to
Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 7

Jul 21, 2016 | 2005 Buick LaCrosse

1 Answer

Unable to start/ 2000 F250 V10


Try first unplugging battery cable for five minutes, this sometimes fix the problem. If it does not replace electric windows relay and electric windows fuse.

Jul 26, 2008 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Toyota avalon drivers side power window broke


glass broke, lot of parts in electric windows to break.

glass.
remove door car.
remove glass holding bracket
remove glass.
its far more complex but
you can read on ALLdata.com
or the FSM.
its all there, read it.
lots of steps. and pitfalls.
on some cars upper door seals need go come out.

Dec 27, 2013 | 2005 Toyota Avalon

1 Answer

Need steps on putting the motor together....torcking steps really


If your rebuilding you need to buy a new bolt kit. you should not use the old bolts and on the kit instrcution it should tell you the torque

Oct 05, 2011 | 1997 Pontiac Sunfire

3 Answers

1997 mercury grand Marquis driverside rear window motor works but window won't go up. Inner door panel off. Metal cable with a black foam cover and pink plastic clip off. Can't figure what it fits to.


usually this means you need a new window regulator.

Section 01-11: Glass, Frames and Mechanisms 1997 Crown Victoria, Grand Marquis Workshop Manual
REMOVAL AND INSTALLATION Window Regulator, Power Front Door
Removal
  1. If front door window glass (21410) is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2.
    1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05 .
    2. Disconnect battery ground cable (14301). Refer to Section 14-01 .
    3. Disconnect window regulator electric drive harness connector.
    4. sva~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Be careful not to strike or scratch front door window glass because it can break.
      Remove window regulator electric drive retaining screws through holes.
    5. Remove window regulator electric drive (23394) from front door power window regulator.
    6. Raise front door window glass to full up position by hand and secure with tape.
    7. Go to Step 5.

  2. Remove front door trim panel and front door trim shield. Refer to Section 01-05 .
  3. Remove front door window glass as described.
  4. Disconnect window regulator electric drive harness connector.
  5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel.

    Remove two 1/4-inch rivets retaining lower bracket of front door power window regulator to inner panel. Use drift punch to knock out center pins for each rivet. Using a 1/4-inch diameter drill, drill out remainder of rivet.
  6. Remove three window regulator electric drive retaining screws from inside door to remove window regulator electric drive from front door power window regulator.
  7. Remove two window regulator retaining nuts.
  8. Remove front door power window regulator from front door (20124).
Installation
  1. Lubricate regulator mechanism with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A.
  1. Install front door power window regulator minus motor (23208) into access hole in inner panel.
  1. Position front door power window regulator using upper studs and tabs on window regulator electric drive mounting bracket.
  1. Install rivets retaining front door power window regulator to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used).
  1. Install two upper front door power window regulator retaining nuts.
  1. Install window regulator electric drive with three screws. Do not overtighten screws.
  1. Connect the window regulator electric drive harness connector.
  1. Install front door window glass.
  1. Adjust front door window glass as described.
  1. Install front door trim shield and front door trim panel. Refer to Section 01-05 snorkelbobby_38.gif

Feb 14, 2011 | 1997 Mercury Grand Marquis

1 Answer

How to replace a electric motor for power window in 1994 honda accord


How to Replace a Window Regulator (with Motor)
(DIY Complexity: Moderate / DIY Time: 2.8 hours)

Parts:
1. Window Regulator

1ed581e.jpg


Tools:
1. Screwdriver
2. Trim Panel Removal Tool
3. 3/8 in. Drive Ratchet
4. Socket Set
5. Riveter Kit

Steps:
Step 1 Remove the door panel by removing the handles and switches. It is required to unscrew or unclip the panel.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.
o Tip: Refer to the vehicle specific service manual if available. There are several fragile plastic clips and hidden screws on the door panel that will break if removed improperly.

Step 2 Remove the vapor barrier.

Step 3 Disconnect the glass from window regulator.

Step 4 Tape the glass to door frame. The glass should not require removal.
o Tip: Tape the glass out of the way to allow access to the window regulator and window lift motor assembly.

Step 5 Disconnect the electrical connector from the window motor.

Step 6 Remove the window regulator mounting bolts. Slide the regulator assembly out through the interior access opening of the door. Remove the motor.

Step 7 Attach the original motor to the new window regulator and install the regulator assembly. Tighten the mounting bolts.

Step 8 Reconnect the electrical connector to the window motor.

Step 9 Install the window back onto the window regulator.

Step 10 Re-install the vapor barrier.

Step 11 Re-install the door trim panel and handles/switches.

Step 12 Test the power window for proper operation by rolling the window up and down in complete cycles for proper testing.
o Tip: After re-installing a window lift motor and regulator, it may be necessary to re-program it following manufacturer specific instructions. Not following or performing this step may result in improper power window function.


Hope helps (remember comment and rated this).

Jun 18, 2010 | 1994 Honda Accord

1 Answer

How to remove a drivers side window motor for


Hello there:
Here is a link to the removal and installation procedures for the window motor and even the switch ok?
I hope that this is very helpful for you
Best regards michael
  1. Chevy Avalanche Fan Club Power Window Sw Replacement - Driver ... Home for Chevrolet Avalanche enthusiasts to learn, discuss, share, and meet. ... Topic: Power Window Sw Replacement - Driver Door ... Installation Procedure ...chevyavalanchefanclub.com/.../index.php/topic,41833.0.html - Cached
  2. Car maintenance, car safety reports at Edmunds TSB Quick Look. 2004 Chevrolet Avalanche 1500 4dr Crew Cab Rwd (5.3L 8cyl 4A) ... POWER WINDOW MOTOR NOW AVAILABLE SEPARATELY FROM THE POWER WINDOW REGULATORY ...edmunds.com/maintenance/recalltsb.do?step=tsb&year=2004&... - 506k - Cached

Nov 09, 2009 | 2004 Chevrolet Avalanche

1 Answer

Driver side rear window doesn't move (electric)


the regulator inside the door has either broken its cable or came loose have to remove door panel inner plastic sheet and look usually u have to replace regulator requiring drill ratchets and silicon about 2-3 hours for semi experienced mechanic can find step by step help in chiltons manual for car availible at most auto parts stores

Jul 07, 2009 | 2004 Pontiac Grand Prix

1 Answer

Remote keyless entry


I assume you are talking about the key fob. First, pry it open and change the battery. Watch which way the + goes.
If your key fob works, and the battery did not fix it, try reprogramming following the instrcutions in the owner manual. May need both fobs present at the same time.
Note; This is different than programming the anti-theft key.

May 27, 2009 | 2003 Ford Windstar

1 Answer

Removing back seats of colorado 2005?


YOU HAVE A BAD SEAL ON THE BRAKE LIGHT OVER THE CAB REPLACE OR RESEAL

Sep 25, 2008 | 2005 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...