Question about 1990 Toyota 4Runner

1 Answer

Need to remove fender trim to get to wheel well to expose power antenna can't remove outer fender trim ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

There are several screws inside the fender well that have to be removed and one in the pinch molding of the car that has to be removed the ones near the engine are snap in plugs and can be removed if you use a flat tip screw driver to remove the plastic push in locks. Remove them to get to the antenna.

Posted on Sep 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove antenna 84 cutlass


Take the inner fender off to expose the screw that holds the bottom of the antenna. Then take off the escutcheon ring that holds the antenna to the fender.

May 25, 2015 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Remove a rear fender from a 2007 rav 4


The short answer is that it is not bolted on and it isn't meant to be removed. The vehicle is uni-body construction, meaning that it is all welded together to form a unit structure and anything that changes the structure could be life threatening. Here is s picture of a Rav4 with the tail light out:
$_57.jpg
To get the outer sheet metal off you need to take out the interior trim and covers to expose the welded structure. The spot welds can be drilled out with a spot weld cutter. Not a job for most people. If it isn't welded back in place correctly, it will affect wheel alignment, rear door sealing and worst case the rear suspension could fall out on the highway. I suggest only a trusted body repair shop handle something like this.

Jan 30, 2015 | 2007 Toyota RAV4

1 Answer

How change front fender f150 2000


Fender -Front Removal
  1. Remove the radiator grille opening panel reinforcement (8A284).
  1. If equipped, remove the front wheel opening moulding.
    1. Remove the pin-type retainer.
    1. Remove the screws.
    1. Remove the wheel opening moulding.
    sy1~us~en~file=n12124a.gif~gen~ref.gif
  1. Remove the front fender splash shield (16103).
    1. Remove the screws.
    1. Remove the pin-type retainers.
    1. Remove the front fender splash shield.
    sy1~us~en~file=gn2615a.gif~gen~ref.gif
  1. Remove the cowl grille.
  1. On RH front fender, remove the antenna mast.
    sy1~us~en~file=k21762b.gif~gen~ref.gif
  1. On RH front fender, remove the antenna base.
    1. Remove the radio antenna base cap (18A927) by gently inserting a thin straight-edged screwdriver underneath the cap and carefully following inside the perimeter until both snaps are free.
    1. Remove the screws.
    1. Lift the antenna base.
    1. Disconnect the radio antenna lead-in cable (18812) and remove the antenna base.
    sy1~us~en~file=k22299b.gif~gen~ref.gif
  1. Remove the fender stuffer.
  1. Remove the stone guard.
    1. Remove the pin-type retainers.
    1. Remove the stone guard.
    sy1~us~en~file=gn2618a.gif~gen~ref.gif
  1. Remove the front fender.
    • Remove the bolts.

Sep 17, 2014 | 2000 Ford F150 Flareside SuperCab

1 Answer

Do I have to remove fender to replace Electric antenna on 1992 Chevrolet Caprice Classic?


if this is in a front fender ,probably not . remove the plastic inner liner around the wheel arch and you will probably get it from there . You may have to take a wheel off to get in. If it is a rear fender the it should be accessible from in the boot after you remove the trim on that side.

Aug 13, 2014 | Cars & Trucks

1 Answer

How to replace a1985 rx7 antenna


you have to remove the tail light assemble to get the antenna and motor out. Remove the 10mm nuts and unplug the harness from the lamp assembly. Carefully remove the assembly, to save the seal. It has to slide to the outside a little to clear the two outer studs.
Remove the back and right side quarter panels. loosen two 10mm nuts for the antenna, remove the retaining ring fender; remove 10mm nuts; unplug power and antenna leads; move bottom of assembly forward to clear fender; remove through tail light hole.

May 29, 2014 | 1985 Mazda RX-7

1 Answer

HOW DO I CHANGE the power antenna on a 1995 chevy impala ss


I will assume its in the trunk? Either way, VERY easy to change! Remove the inside trunk panel to expose the motor. there may be one or two nuts holding it in place! First disconnect the power wire plug. then remove the one or two nuts, holding it in place. Last unscrew the ring on top and it should drop right into your trunk. Install in reverse order. IF its in your front fender, you may be able to get to it from the wheel well. You would have to remove the splash guard from the outside part of fender!

Aug 15, 2012 | Cars & Trucks

2 Answers

Where is the power antenna motor located for a 1992 buick regal?


I have not owned a buick for years. However, the one I did have trouble with the power antenna motor was located directly under the antenna. It was in the rear fender housing. I have to remove the trunk lining on the side of the fender. It was mounted a bracket. It was easy to replace as it all comes as a complete assembly. Hope that helped

Feb 21, 2012 | 1992 Buick Regal

2 Answers

My antena wont go down ,and the motor wont go off , even when the car is shut off .


Unplug the harness to the ant.It will not go off,until you replace the whole ant.mass.The gear(plastic)are stripped out,and the motor can not sense that the any.is moving.

Jan 19, 2010 | 1991 Oldsmobile Eighty Eight

2 Answers

Problem removing broken antenna mast


you have to pull out the trunk interior trim panels on the left side to access it.
there will a few 10mm bolts and a connector.

May 07, 2009 | 2006 Hyundai Sonata

1 Answer

97 F-350 Headlight door removal


The front couple bolts (enough to fold the inner fender wells) on the fender wells (plastic part around inside the wheel well). Take them out, I think i did 6. Basically, just do what you have to do to fold the front part of that plastic inner fender well enough to see behind the parking light, then you need to remove the parking light/corner light assy. and once they are out you can reach the final screws required to remove the headlight trim rings. Also there are a few people on EBAY that are selling replacement headlight/parking/corner light assemblys that have clear outer lenses that dont get all yellow and foggy as the stock ones do. I bought smoked ones that have a light tint to it and they have projector caps so you can use HID kits and get a nice beam. something you might want to look into if your going to do the trim rings since its kind of a p.i.t.a.

Oct 15, 2008 | 1997 Ford F350 Crew Cab

Not finding what you are looking for?
1990 Toyota 4Runner Logo

Related Topics:

369 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...