Question about 2001 GMC Jimmy

Open Question

Installing a dash assembly for a 2001 GMC Jimmy

Installing the dash assembly for a 2001 GMC Jimmy

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2001 gmc jimmy engine warm but heater blows cold air

Disconnect the heater hoses from the water pump and the intake manifold. Get a compressor and blow out the hose (put the air hose into the the hose that came off the mainfold. then flush the system and replace the antifreeze.

Posted on Dec 12, 2008

Ad
picatudo
  • 239 Answers

SOURCE: 2001 gmc jimmy defroster-heater blower will not direct heat

you have a vacuum leak

Posted on Jan 07, 2009

  • 366 Answers

SOURCE: install wheel hub assembly

take frt tire off,brake calyper and bracket,disc rotor,undo cv shaft bolt,unplug abs sensor under rubber splash guard ,undo 4bolts for hub bearing assembly from steer. knuckle.

Posted on Feb 22, 2009

  • 3 Answers

SOURCE: 2001 GMC Jimmy - Wheel bearings

if u have to replace the whole hub asym it will come all togather.. or as a set of bearings that just sit in the hub.

Posted on Apr 03, 2009

  • 91 Answers

SOURCE: 2001 GMC Jimmy break lights not working but all

Check the brake light switch should be a orange wire with 12v then a white wire with 12v when the pedal is pressed.If htat cks good then ck the hazard switch by moving it up and down and wiggeling the knob with the brake pedal pressed if they start working then your multifunction switch is bad and needs to be replaced.

Posted on Feb 20, 2010

Testimonial: "We check and you were right on the money. It's the hazard switch carrier. Thanks for you help."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

No power of any kind on 2001 GMC JImmy looking for fusible link


check fuses under hood for the main power coming from battery

Aug 26, 2012 | 2001 GMC Jimmy

1 Answer

I have a 2001 GMC jimmy sport(2door)..4.3 ,,The fuel pump quit working and fuel gauge was off , So i bought a whole new pump assy and installed it in tank,, Now i got no fuel reading or pump working Took...


I would replace the harness going to the pump assembly. They are notorious for going bad. A lot of the new pumps come with it. Hope this helps, TJ

Aug 06, 2011 | 2001 GMC Jimmy

2 Answers

Where is the GMC Jimmy 2001 fuel pump relay located in the car?


under relay box . some models is under dash near center of dash

Dec 12, 2010 | 2001 GMC Jimmy

2 Answers

Where is the release for the hood on a 2001 GMC Jimmy


The hood release is located above where the drivers left leg would be on the dash board.

May 17, 2010 | 2001 GMC Jimmy

1 Answer

2001 GMC Jimmy 2D won't pass inspection because the parking brake won't stay down. Is this an expensive fix?


No, it's not that expensive. I have the same problem and am fixing it now.
Basically you need to replace the parking brake assembly that is held on with 3 bolts, and the 2 cables. ( brake cable and release handle )
The Brake cable has three flared tabs you need to squeeze to get it out of the assembly.
Get a replacement brake assembly at your local wreckers, Mine will cost $22.00
Re-install the large cable with the flanges and then bolt it in, then attach the release cable.
Done!

Apr 10, 2010 | 2001 GMC Jimmy

1 Answer

I have a 2001 gmc jimmy the altenator has a plug with 2 wires i whant to no what the wires are and wher they go


one wire is to excite ( turn on ) the voltage regulator the other is for the gauge or warning lamp on the dash

Nov 07, 2009 | 2001 GMC Jimmy

1 Answer

2001 GMC Jimmy - Wheel bearings


if u have to replace the whole hub asym it will come all togather.. or as a set of bearings that just sit in the hub.

Apr 03, 2009 | 2001 GMC Jimmy

1 Answer

Heat not working right


close the firewall damper under the dash

Mar 22, 2009 | 2001 GMC Jimmy

1 Answer

Install wheel hub assembly


take frt tire off,brake calyper and bracket,disc rotor,undo cv shaft bolt,unplug abs sensor under rubber splash guard ,undo 4bolts for hub bearing assembly from steer. knuckle.

Jan 04, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
2001 GMC Jimmy Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...