Question about Hyundai Sonata

1 Answer

I have 2006 Hyundai Sonata 3.3 v6 Engine, it has a check engine light is on and the scanner shows ( crankshaft, camshaft position sensor) mt technicians says it is a timing chain problem specially it make a noise when you start it in the morning. what is your advise to fix it as cheap as possible.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 435 Answers

Hi,i advise you to change the timing,its really .As if you miss to change the timing chain,unlucky that brake,this can cost you 10 times more if that happen,so man i advise you to change it as soon as possible,its really important.....

Posted on Sep 05, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Camshaft Position sensor located on a 2000 Hyundai Sonata V6


normally that is inside the distributor housing or on its shaft . though im an old mechanic an just guessing

Oct 21, 2014 | Cars & Trucks

3 Answers

Sonata engine cranking but not firing


Proceed like this :
(1) Check the fuel flow , could be problem of fuel pump.
(2) Check the camshaft and crank shaft position sensor , there must MIL light glowing because of it. If yes , The Camshaft Position sensor is typically located in the cylinder head of the engine and has a cylindrical portion that inserts into the head. The Crankshaft Position sensor is normally located in the timing cover or on the side of the block with a cylindrical portion that inserts into the block.
If No, fuel pump could be the only problem.

Apr 25, 2014 | 2006 Hyundai Sonata

1 Answer

WEAR IS THE CAMSHAFT POSTION SENSOR ON A 2005 HYUNDIA SONATA V6 2.7L


It is buried under fuel hoses and vacuum lines follow top radiator hose to engine under fuel line between air cleaner box and head

Apr 23, 2012 | 2000 Hyundai Sonata

1 Answer

How do you replace a 2006 crankshaft position sensor?


The 2006 came with a 4 cyl and a 6 cly engine - the crank position sensor is in a different location on each. On the 4 cyl, it's on the back side of the engine block (firewall side) behind a heat shield. on the V6 it's below the exhaust manifold (LH side - Radiator side) in the engine block near the transmission. Both are attached with a 10mm bolt.

Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop manuals, service bulletins, illustrations and procedures, etc.

Sep 01, 2011 | 2006 Hyundai Sonata

2 Answers

I can't find the location of the crankshaft postion sensor in my 2000 Hyundai sonata


My online Sonata manual shows these possibilities, but does not identify which applies specifically to 2000 Sonata.
Also, when you talk to the dealership parts counter, you'll need to know whether your 2000 Sonata is (a) 4-cylinder 2.4L MFI DOHC engine, or (b) 6-cylinder 2.5L MFI DOHC engine.
Its easy to tell - just count your spark plug wires.

-- begine excerpt from 2000 Hyundai Sonata Repair guide --

The crankshaft position sensor is located next to the flywheel.
The crankshaft position sensor is located next to the flywheel/torque converter.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The crankshaft position sensor is located on the driver-s side of the vehicle, down by the lower radiator hose.
The crankshaft position sensor is located on the engine near the crankshaft pulley.
The crankshaft position sensor is located at the front of the engine near the timing belt.

--- end excerpt from 2000 Hyundai Sonata repai guide ---

Dec 29, 2010 | 2000 Hyundai Sonata

1 Answer

I have a 2000 hyundai Sonata, 6 cylinder eng. My


The sensor is located on the left hand rear side of the block (near the bell housing). It is held in place by a 10mm bolt. It's to the right of the exhaust manifold (LH - radiator side) on the V6. Once you purchase the new sensor you'll be able to identify it on the engine. The connector to this sensor is located in the illustration.
2cb09a4.jpg A word to the wise... replace the O2 snsr as well.

Sep 24, 2009 | 2000 Hyundai Sonata

2 Answers

1995 hyundai sonata turns over but will not start


sounds like a crank position sensor. Whenever the "Check Engine" light comes on, there is always a DTC (Diagnostic Trouble Code) stored in the ECM (Engine Control Module). You'll need an OBDI/II (On-Board-Diagnostics) scanner to retrieve any codes recorded/set in ECM. Once you do this and let us know what, if any codes are set, then we can go from there.

Jun 11, 2009 | 1995 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8825 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...