Question about 2003 Ford E150

1 Answer

I have 2002 econoline 150 and need to replace or disable the shift interlock actuator, I have replaced the relay. I am having to replace fuse #11 I have to put shifter in N to keep from blowing fuse when i start the van. It also seems to be intermittent sometimes it will take a couple of days before the fuse blows if I forget and stsrt it up. If you can send a picture and wiring diagram It would be helpful. Thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 24 Answers

If you look on your brake pedal there is a switch that has two green wires. Inspect that and make sure it is not melted or burned, causing you to blow your fuse.

Posted on Sep 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 merc grandmarkee wont go into park wont start will start if you wiggle in nutral


Park neutral safety switch could be bad , also the shift interlock safety system .
Shift Interlock System A brake/shifter interlock system consists of the following:
  • ignition switch (11572)
  • brake pedal stoplight switch (13480)
  • brake shift interlock module
  • brake shift interlock solenoid assembly (attached to key interlock assembly)
  • necessary wiring
On floor-shift vehicles, the ignition/shifter interlock cable (3F719):
  • locks the floor shift transaxle range selector lever in the PARK position when the ignition switch is in the LOCK position.
  • requires the floor shift transaxle range selector lever to be in the PARK position to turn the ignition switch to the LOCK position.
Condition Possible Source Action
  • Shift Interlock System Does Not Release or Lock Properly
  • Circuitry open/shorted.
  • Blown fuse.
  • Damaged stoplight switch.
  • Damaged shift lock actuator.
  • GO to Pinpoint Test A .

PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE OR LOCK PROPERLY A1 CHECK ELECTRON IGN FUSE
  • Check Fuse 5 (5A) located in fuse junction panel.
Is fuse OK?
Yes No GO to A3 . GO to A2 . A2 CHECK FOR SHORT TO GROUND
  • Turn ignition switch OFF.
  • Remove Fuse 5 (5A).
  • Disconnect shift-lock actuator connector C203 located to the right of steering column.
  • Measure resistance of the Circuit 1003 (GY/Y) between the correct terminal of Fuse 5 (5A) and ground.
Is resistance greater than 10,000 ohms?
Yes No REPLACE Fuse 5 (5A). GO to A3 . SERVICE Circuit 1003 (GY/Y) wire between fuse junction panel and shift-lock actuator. A3 CHECK POWER SUPPLY FROM FUSE 5 (5A)
  • Reinstall Fuse 5 (5A).
  • Turn ignition switch to RUN.
  • Measure voltage on Circuit 1003 (GY/Y) wire and ground.
Is voltage greater than 10 volts?
Yes No GO to A4 . SERVICE Circuit 1003 (GY/Y) wire between interior fuse panel and shift-lock actuator. A4 CHECK POWER SUPPLY FROM FUSE 28 (15A)
  • Turn ignition switch OFF.
  • Disconnect connector C2016.
  • Turn ignition switch ON.
  • Measure voltage on Circuit 10 (LG/R) and ground.
Is voltage B+?
Yes No GO to A5 . SERVICE Circuit 10 (LG/R) for open. RESTORE vehicle and RETEST system. A5 CHECK WIRE BETWEEN STOPLIGHT SWITCH AND SHIFT-LOCK ACTUATOR
  • Turn ignition switch OFF.
  • Disconnect shift-lock actuator connector C203.
  • Apply brake pedal.
  • Measure voltage on Circuit 810 (R/LG) wire and ground.
Is voltage greater than 10 volts with brake pedal applied and less than 1 volt with brake pedal released?
Yes No GO to A6 . SERVICE Circuit 810 (R/LG) wire between stoplight switch and shift-lock actuator. A6 CHECK SHIFT-LOCK ACTUATOR GROUND
  • Measure resistance of Circuit 57 (BK) and ground.
Is resistance less than 5 ohms?
Yes No REPLACE shift-lock actuator. SERVICE BK wire.

Mar 30, 2017 | Cars & Trucks

1 Answer

Shifter stuck in park 02 ford explore.


Most likely a problem with the
Shift Interlock System
The shift interlock system prevents the shifting from PARK unless the brake pedal (2455) is depressed. The shift interlock system consists of a shift lock actuator (3Z719) mounted at the base of the steering column tube (3514). If the ignition switch (11572) is in the RUN position, the shift lock actuator is continually on unless the brake pedal is depressed.
Could have a bad brake switch , do the brake lights work ?
Inspection and Verification
  1. Verify the customer concern by operating the transmission external control.
  1. Visually inspect for obvious signs of mechanical and electrical damage, incorrect component installation, and component misalignment. Verify that all circuit-related systems are functioning correctly. Refer to the following chart:

    Visual Inspection Chart Mechanical Electrical
    • Damaged shift lock actuator
    • Damaged brake pedal position switch
    • Damaged steering column
    • Damaged transmission control switch
    • Damaged instrument cluster
    • Damaged shift cable and bracket
    • Failed fuse(s)
    • Damaged wiring harness
    • Loose or corroded connections
  1. If the fault is not visually evident, proceed to the Symptom Chart
SYMPTOM CHART Condition Possible Sources Action
  • Shift Interlock System Does Not Release/Lock Properly
  • Circuit(s).
  • Fuse(s).
  • Shift lock actuator.
  • Brake pedal position (BPP) switch.
  • GO to Pinpoint Test A .
PINPOINT TEST A: THE SHIFT INTERLOCK SYSTEM DOES NOT RELEASE/LOCK CORRECTLY CONDITIONS DETAILS/RESULTS/ACTIONS A1 TEST FUSE 10 (7.5A)
Fuse 10 (7.5A)
Measure the resistance of fuse 10.


  • Is the resistance 5 ohms or less?
Yes GO to A2 .

No GO to A3 . A2 CHECK THE POWER SUPPLY TO THE SHIFT LOCK ACTUATOR-CIRCUIT 1003 (GY/YE)
Shift Lock Actuator C289
Measure the voltage between the shift lock actuator C289 pin 3, circuit 1003 (GY/YE), harness side and ground.
  • Is the voltage greater than 10 volts?
Yes GO to A5 .

No GO to A4 . A3 TEST CIRCUIT 1003 (GY/YE) FOR SHORT TO GROUND
Shift Lock Actuator C289
Measure the resistance at C289 pin 3, circuit 1003 (GY/YE).
  • Is the resistance 10 K ohms or less?
Yes REPAIR circuit 1003 (GY/YE) for short to ground. TEST the system for normal operation.

No INSTALL a new shift lock actuator. TEST the system for normal operation. A4 TEST CIRCUIT 1003 (GY/YE) FOR OPEN Measure the resistance of circuit 1003 (GY/YE) between the output side of fuse 10 (7.5A) and the shift lock actuator C289 pin 3.
  • Is the resistance 5 ohms or less?
Yes GO to A5 .

No REPAIR circuit 1003 (GY/YE) for open. TEST the system for normal operation. A5 CHECK FUSE 9 (7.5A)
Fuse 9 (7.5A)
Measure the resistance of fuse 9 (7.5A).
  • Is the resistance 5 ohms or less?
Yes GO to A8 .

No GO to A6 . A6 TEST CIRCUIT 276 (BN) FOR SHORT TO GROUND.
Brake Pedal Position (BPP) Switch C224
Measure the resistance of circuit 276 (BN) between C224 pin 3 and ground.
  • Is the resistance 10 K ohms or less?
Yes REPAIR circuit 276 (BN) for short to ground. TEST the system for normal operation.

No GO to A7 . A7 TEST CIRCUIT 810 (RD/LG) FOR SHORT TO GROUND
Shift Lock Actuator C289
Depress the brake pedal and measure the resistance between C289 pin 1 and ground.
  • Is the resistance 10 K ohms or less?
Yes REPAIR circuit 810 (RD/LG) for short to ground. TEST the system for normal operation.

No INSTALL a new shift lock actuator. TEST the system for normal operation. A8 CHECK FOR B+ ON CIRCUIT 810 (RD/LG)
Shift Lock Actuator C289
Depress the brake pedal and measure voltage at C289 pin 1.
  • Is the voltage 10 volts or greater?
Yes GO to A12 .

No GO to A9 . A9 TEST CIRCUIT 276 (BN) FOR OPEN
Brake Pedal Position (BPP) Switch C224
Measure the resistance between the output side of fuse 9 (7.5A) and the brake pedal position switch pin 3, circuit 276 (BN).
  • Is the resistance 5 ohms or less?
Yes GO to A10 .

No REPAIR circuit 276 (BN) for open. TEST the system for normal operation. A10 TEST BRAKE PEDAL POSITION SWITCH Measure the resistance of the brake pedal position switch, while open (OFF) and closed (ON), between pin 2 and pin 3 of C224.
  • Is the resistance of the switch greater than 10 K ohms while OFF and 5 ohms or less while ON?
Yes GO to A11 .

No INSTALL a new switch. TEST the system for normal operation. A11 TEST CIRCUIT 810 (RD/LG) FOR OPEN
Brake Pedal Position (BPP) Switch C224

Shift Lock Actuator C289
Measure the resistance between C224 pin 2 and C289 pin 1.
  • Is the resistance 5 ohms or less?
Yes INSTALL a new shift lock actuator. TEST the system for normal operation

No REPAIR circuit 810 (RD/LG) for open. TEST the system for normal operation. A12 CHECK CIRCUIT 57 (BK) FOR AN OPEN Measure the resistance between the shift lock actuator C289 pin 2, circuit 57 (BK), harness side and ground.
  • Is the resistance less than 5 ohms?
Yes INSTALL a new shift lock actuator. REFER to Brake Shift Interlock Actuator in this section. TEST the system for normal operation.

No REPAIR circuit 57 (BK). RECONNECT all components. TEST the system for normal

Mar 28, 2017 | 2002 Ford Explorer

1 Answer

2010 merc gm shift lever stuck in park car will start steering wheel turns


You have a shift interlock problem . What kind of vehicle ? a mercury what ?
Shift Interlock System
The shift interlock system prevents shifting from PARK unless the brake pedal is depressed. The shift interlock system consists of a shift lock actuator mounted on the selector lever. If the ignition switch is in the RUN position, the shift lock actuator is disabled when the brake pedal is depressed.
If the selector lever will not move out of PARK with the key in the ON position and the brake pedal depressed, it will need to be unlocked manually.
Do the brake lights work ?
Visually inspect for obvious signs of mechanical and electrical damage; refer to the following chart:

Visual Inspection Chart Mechanical Electrical
  • Damaged shift lock actuator
  • Damaged transmission control (TC) switch
  • Damaged shift interlock switch
  • Failed fuse(s):
    • F20 (10A)
    • F22 (15A)
  • Damaged wiring harness
  • Loose or corroded connections
  • Damaged shift interlock switch
Symptom Chart Condition Possible Sources Action
  • Shift interlock system does not release/lock correctly
  • Circuitry
  • Fuse(s):
    • F20 (10A)
    • F22 (15A)
  • Brake pedal position (BPP) switch
  • Brake shift interlock actuator
  • Brake shift interlock actuator module
  • Go To Pinpoint Test A .
PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE/LOCK CORRECTLY Test Step Result / Action to Take A1 TEST THE BRAKE LIGHTS
  • Apply brake pedal and view brake lights.
  • Do brake lights illuminate?
Yes
GO to A7 .

No
GO to A2 . A2 TEST FUSE F22 (15A)
  • Key in OFF position.
  • Check fuse: Smart Junction Box (SJB) Fuse F22 (15A).
  • Is the resistance less than 5 ohms?
Yes
GO to A4 .

No
GO to A3 . A3 TEST THE CIRCUIT FOR A SHORT TO GROUND
  • Key in OFF position.
  • Disconnect: Brake Pedal Position (BPP) Switch.
  • Measure the resistance between pin 1 and ground.
    s7n~tr~en~file=n0039468.gif~gen~ref.gif
  • Is the resistance greater than 10,000 ohms?
Yes
GO to A4 .

No
REPAIR circuit for short to ground. TEST the system for normal operation
Do

Jun 19, 2016 | 2010 Mercury Grand Marquis

2 Answers

Can't shift out of park, no brake lights


This is a problem with the brake sensor lockout. Most likely it is out of place or broken and shorting. It is on the brake pedal lever.

Dec 09, 2015 | 2002 Ford Escape

1 Answer

Brake shift interlock solenoid


column or floor shifter ?
Brake Shift Interlock Actuator - Floor Shift Removal and Installation
NOTE: The brake shift interlock actuator is not serviced individually. If replacement is required, install a new floor shift selector lever assembly.
For additional information, refer to Selector Lever - Floor Shift in this section.
Brake Shift Interlock Actuator - Column Shift Removal and Installation
  1. Set the parking brake.
  1. Remove the steering column shrouds.
  1. Turn the ignition to the accessory position and apply the brake or actuate the brake shift interlock actuator (BSIA) override.
  1. Put the selector lever into the NEUTRAL position.
  1. Disconnect the BSIA electrical connector.
  1. Remove the BSIA screw.
  1. Gently pry the clip up and remove the BSIA.
  1. NOTE: During installation, verify that the BSIA override has been activated and the slider is fully rearward. Before rotating the selector lever from NEUTRAL into PARK, align the selector lever tab into the BSIA. To install, reverse the removal procedure.

May 26, 2017 | Ford Expedition Cars & Trucks

1 Answer

My mechanic tells me I need a new interlock shift in my 2002 GMC Envoy. On ocassion, I need to pump my brakes a few times before I am able to move my gear from park to drive. The shifter is cheap but the...


Before any parts are replaced, it needs to be determined if the brake pedal switch is being actuated properly and functioning properly. After that, the interlock solenoid needs to be checked, as well as the linkage.

Jan 03, 2013 | 2002 GMC Envoy

1 Answer

Hi, I have a 96 windstar. One of the wires on the brake light switch down at the brake pedal has broke at the plug and then when I went to repair it touched the steering bar and sparks flew. Once I...


fuse #7 - 15 amp , Fuse #21 - 10 amp.

Maybe you blew solid state module. There is a manual bypass.

Shift Interlock System A shift interlock mechanism prevents shifting the transaxle out of the PARK position unless the brake pedal (2455) is applied. The shift lock actuator is energized when the ignition switch is turned to the RUN position.
  • This locks the shifter in the PARK position.
  • When the brake pedal is applied and the stoplight switch (13480) is activated, the shift lock actuator is deactivated and the shifter can be moved out of the PARK position.
-----------------------------------------------------
  • Shift Interlock System Does Not Release or Lock Properly
  • Fuse.
  • Circuit.
  • Shift lock actuator.
  • Gearshift lever adjustment.
  • Stoplight switch.

----------------------------------------------------------

1c38cb8.gif

Oct 30, 2010 | 1996 Ford Windstar

2 Answers

Fuel Pump isnt running. will not start. Its not the collision reset. Simply no elec going to the pump at all. Ran fine yesterday.


Fuel Pump Relay can cause this, so can a bad ground or a dead pump. I would also check the fuse for the Fuel Pump.

Jun 20, 2010 | 1989 Ford Econoline

1 Answer

Ford Expedition 2001 that wont shift out of Park


Shift Interlock System
The shift interlock system prevents the shifting from PARK unless the brake pedal (2455) is depressed. The shift interlock system consists of a shift lock actuator (3Z719) mounted at the base of the steering column tube (3514). If the ignition switch (11572) is in the RUN position, the shift lock actuator is continually on unless the brake pedal is depressed.

Thier is also the shift lock actuator ! plus wiring . You have a short to ground on that circuit . Do you know how to Find a short ? videos on youtube .
None of the power windows work ? Check for broken wires inside the rubber boot from the body to drivers door !
Videos on youtube for testing power window circuits .
How to test power window switch motor 1985 2001 Toyota

May 03, 2017 | 2001 Ford Expedition

1 Answer

I want to disable the fuel pump to replace filter on a 99 econoline v6. My fuse box is missing the diagram so I have no idea which fuse or relay controls the pump. Can someone show me the diagram?


i would just diconnect the positve cable on the battery, or just dont leave the keys in it when you change it , reliev the pressure from the line from the shder valve under the hood in the fuel rail is all,

May 10, 2009 | 1999 Ford Econoline

Not finding what you are looking for?
Cars & Trucks Logo

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...