Question about 2006 Mitsubishi Eclipse

Open Question

I have a2006 mitsu/eclipse 3.8 i'm trying to install an AEM cold air intake.When i install it the check engine light comes on.THe traction control turns off.What do i do to fix this.ONe more thing there is a plug for the factory intake box that is left loose.What do i do with this plug.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A 98 Lincoln town car and when I reach 35/40mph my car does not keep going. The track light comes on. And when I'm going up hill it also drops in speed quickly. The car has back fired twice on me


Possible plugged catalytic converter ! is the check engine light on ? You should take it an have scan tool hooked up to see if any codes are stored in any control modules ! An have exhaust system pressure tested !

Aug 30, 2015 | Lincoln Cars & Trucks

1 Answer

My traction control light came on after installing an Volant cold air intake on my 2006 CADILLAC XLR V HELP ME PLEASE


Most likely the air induction probably needs to be programmed into the ECM. But also you may have jounced a wire that has a connection to traction control and it is setting it off. Otherwise, you may have a standard trAction control problem that has to be addressed in the shop.

Dec 18, 2013 | Cars & Trucks

2 Answers

2000 Mitsubishi Eclipse Problem TCL


2 concern for you when check engine light comes on your TCL (traction control) is disabled,so you get the light,and if TCL is disabled so is the ABS (anti lock brakes) you first step is get the Check engine light code,If it was just a TCL light on the ABS code will need to be gathered,You need a scan tool

Dec 08, 2012 | 2000 Mitsubishi Eclipse

1 Answer

When i brake on my 2003 supercrew, it sounds almost as if a horn is blowing. very annoying


Hello, You may have a bad brake booster, there can be a check valve in the feed line to the booster. You need to have a pressure check done on the brake booster. Be careful not to use any chemical which can dissolve rubber or plastic if you use a spray around the booster. A water spray may indicate a leaking booster if you test it with the engine running. The rpm will change from a leak.

The ABS system should show a "check light" if it is malfunctioning. The modulation inside the brake unit possibly could make noise.

The Traction control, if equipped, can activate a control valve in the intake system to limit engine RPM. When this system works, it shuts off intake air to slow down the engine when the system detects slippage in the rear wheels. If you have a toggle button on the dash to switch off the Traction control, turn the sytem off and try driving it and see if the noise goes away. Debris in the rear rotor "drum" brake could possibly blind a wheel sensor counting the revs and activate the Traction control

Idle speed control "motor" is a type of intake air control used to smooth out the engine. It operates in a air chamber and its the last thing I can think of that even remotely could make a noise.

Jun 23, 2011 | 2003 Ford F150 Regular Cab

1 Answer

What does the tcl dash light on a 2002 mitsubishi gallant ls mean


tcl is traction control. Google eclipse tcl and you will find your answer. Sounds like it is a common problem with the MAP sensor when people put on aftermarket air intakes.

Apr 04, 2010 | 2004 Mitsubishi Eclipse

2 Answers

Transmission rebuilt 5 years ago on a 1997 Eclipse RS. Now, the RPM levels are extremely high even without full acceleration.


The likely cause for your high RPM may be caused by a vacuum leak in the engine. You can open the hood and check your hoses for cracks and leaks. This is a good place to start, but may no be a full solution.

Feb 03, 2010 | 1996 Mitsubishi Eclipse

1 Answer

Starts but dies when engine warms up


Ok, i have a 93 mitsubishi eclipse, so same motor as mine. I had a similar problem after replacing my battery. In removing the intake tube, it split for about 3 inches on the underside of the tube, allowing air to bypass the air intake sensor ( the place where the tube connects to the filter housing). Check this and let me know :)

Apr 30, 2009 | 1992 Eagle Talon

1 Answer

Pi4oo MSP trouble code mitsu eclipse 1995


The error is actually P1400 Manufacture Controlled Auxillary Emissions Controls. I'm having that issue with my 2001 Mitsubishi Eclipse right now. Not to mention the bad paint job.

Jan 16, 2009 | 1995 Mitsubishi Eclipse

Not finding what you are looking for?
2006 Mitsubishi Eclipse Logo

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...