Question about 1990 Nissan Pulsar

Open Question

1992 nissan pulsar trying to remove passenger door panel have removed all the obvious screws cant see how to get past the door opening lever

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 nissan 350z. Passenger door electric locks only unlock half way. Problem is I can get door panel off being door is shut and cant open from outside/inside.....What now lol


Remove the front seat can give you access to remove the panel. But if it has screws around the outer perimeter, most likely will have to tear it out. Best to find a replacement first. Look at the drivers door, if it has screws, so does the passenger side. There are screws around the arm rest and door handle to remove, then it pops off. Again the seat has to be out of the way.

Oct 30, 2016 | 2003 Nissan 350Z

1 Answer

How do I remove front pasenger door panel? cant get past door lever opening mechanism. It's a nissan micra which is not on model options list - so I just picked murana without knowing what a murano is.


Hi,
when removing most vehicle interior door panels, a little jiggling is often required. However, double check and ensure that you have removed all securing screws and GENTLY pulled the panel and the plastic push-studs that secure it to the door sheet metal.
Check that there is not a "finishing" piece at the door lever opening which will have to be GENTLY removed and there may be a panel securing screw hidden behind it. Sometimes it is just easier to remove the securing screws from the actual door lever which should result in more area to work with.

Lift the fully released door panel up slightly, then rotate it untill you see the aperture is diagonal to the door lever opening, then carefully ease the panel out past the door lever.

A word of warning all modern carts use plastic securing / holding sevices, like push-studs, clips, 1/2 clip[s etc. They are extremely brittle and break very easily. Exercise extreme caution when removing the panel and even more when re-fitting it to the door. Do NOT force any fitting into it's receptacle unless you are POSITIVE it is in alignment. You might like to put some liquid soap on the plastic securing pins /studs/etc. The soap will ease the entry and will not harm any fittings and will eject it's self in a short period of time.

You may wish to invest in a trim removal tool. They are inexpensive and will pay for it's self the first time that you use it.

Good luck.

Jan 31, 2011 | Nissan Murano Cars & Trucks

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

Passenger door does not unlock


your going to have to get that panel off with out opening the door.
remove screws ffrom door panel and try to pull up from bottom. put the passenger seat all the way back. be careful and take your time it can be done

Jul 24, 2010 | 1993 Nissan Altima

1 Answer

I own a 1993 nissan pulsar, i think also known as...


Have you checked whether you removed the screw door handle? It's accessible when you pry off the plastic of the door handle carefully..

May 17, 2010 | Cars & Trucks

1 Answer

How do i remove door panel to get window runner


The panel is usually a pop button type retainers holding the panel on, Obviously all screws will have to be removed ie; grab handle, internal door opening lever, and the window winder,
TIP remove window winder handle with a shoe lace or a lenght of thin material , it's a horseshoe shaped spring clip holding the winder handle on and pulling the shoe lace or material in the opposite direction of clip will easily remove clip (don't loose ) Good luck

Apr 10, 2010 | 2003 Nissan Se R

1 Answer

Window on driver side will not go up. Nissan stanza 1992 model. Electric window. How to remove door panel


There are a number of screws and clips holding that particular door panel onto the door. Recommend you get a service manual with a detailed diagram showing how to disassemble that panel, else you might destroy most of the clips trying to remove the panel.

Jan 30, 2010 | 1992 Nissan Stanza

2 Answers

Temp gauge reads half but there is no heat blowing


the door inside the heater control box unit may be stuck shut. It runs off a vacuum port to open

Jan 24, 2010 | 1992 Nissan Stanza

1 Answer

Removal of Front Door Handle Pintara Nissan


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.

Sep 21, 2009 | 1983 Nissan Pulsar

Not finding what you are looking for?

Open Questions:

See all 1990 Nissan Pulsar Questions

1990 Nissan Pulsar Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...